All MIBs › CISCO-DOT11-RADIO-DIAGNOSTIC-MIB › cDot11RadioDiagMode
cDot11RadioDiagMode
Module: CISCO-DOT11-RADIO-DIAGNOSTIC-MIB
OID (symbolic): CISCO-DOT11-RADIO-DIAGNOSTIC-MIB::cDot11RadioDiagMode
OID (numeric): 1.3.6.1.4.1.9.10.105.1.1.1.1.3
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Test mode as carried by the Cisco Radio Management Extensions in the 802.11 beacon frame.
The semantics are described as follows.
normal - Indicates that the station is operating in non-test mode.
apRadioDiscovery - Indicates that this station is operating in AP Discovery mode. In this mode, APs transmit and measure each other's beacons. APs measure signal strength as received from other APs, levels of RF interference experienced during transmission / reception and report back the same to the NM.
siteSurveyTempSettings - Indicates that the station is operating in AP assisted site survey mode with temporary channel and transmit power settings applied to the dot11 interface identified by ifIndex.
siteSurveyNonTempSettings - Indicates that station is operating in AP assisted site survey mode with it's original channel and transmit power with the temporary settings not applied to the dot11 interface identified by ifIndex.
What is cDot11RadioDiagMode?
A read-write setting that controls the diagnostic test mode advertised in Cisco Radio Management Extensions within 802.11 beacon frames, such as normal operation versus AP radio discovery mode.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.105.1.1.1.1.3 snmpwalk -v2c -c public <target> CISCO-DOT11-RADIO-DIAGNOSTIC-MIB::cDot11RadioDiagMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.105.1.1.1.1.3.1 snmpget -v2c -c public <target> CISCO-DOT11-RADIO-DIAGNOSTIC-MIB::cDot11RadioDiagMode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.105.1.1.1.1.3.1 i <value>
Start monitoring Cisco 802.11a/b/g access points and wireless bridges with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-DOT11-RADIO-DIAGNOSTIC-MIB::cDot11RadioDiagMode OID value, configure state conditions and alerts, and monitor any Cisco 802.11a/b/g access points and wireless bridges from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.105 | ciscoDot11RadioDiagMIB | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |
| 1.3.6.1.4.1.9.10.105.1 | cDot11RadioDiagMIBObjects | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |
| 1.3.6.1.4.1.9.10.105.1.1 | cDot11RadioDiagConfigGlobal | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |
| 1.3.6.1.4.1.9.10.105.1.1.1 | cDot11RadioDiagTable | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |
| 1.3.6.1.4.1.9.10.105.1.1.1.1 | cDot11RadioDiagEntry | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |
| 1.3.6.1.4.1.9.10.105.1.1.1.1.3 | cDot11RadioDiagMode | CISCO-DOT11-RADIO-DIAGNOSTIC-MIB |