All MIBs › CISCO-ATM2-MIB › ciscoatmSigEmitCldPtyEvents
ciscoatmSigEmitCldPtyEvents
Module: CISCO-ATM2-MIB
OID (symbolic): CISCO-ATM2-MIB::ciscoatmSigEmitCldPtyEvents
OID (numeric): 1.3.6.1.4.1.9.10.23.1.1.1.14
Node type: OBJECT-TYPE
Type: Counter32
Access: read-only
Description: Number of Called Party Responsible For Unsuccessful Call transmitted from this interface. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction (CLIR) 27 destination out of order 31 normal, unspecified 88 incompatible destination
NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.
What is ciscoatmSigEmitCldPtyEvents?
This counter increments when this interface itself transmits a message attributing a call failure to the called party. This is this switch relaying that failure verdict back toward whoever originated the call, confirming the called-party-attributable cause was generated toward the far end, useful for distinguishing whether this switch detected the bad news itself or is simply passing it along from further downstream. This counter rising in tandem with ciscoatmSigDetectCldPtyEvents on the same interface for the same call pattern confirms this switch is both seeing and relaying genuine called-party failures rather than manufacturing them.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.23.1.1.1.14 snmpwalk -v2c -c public <target> CISCO-ATM2-MIB::ciscoatmSigEmitCldPtyEvents
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.23.1.1.1.14.1 snmpget -v2c -c public <target> CISCO-ATM2-MIB::ciscoatmSigEmitCldPtyEvents.1
Start monitoring Cisco routers/switches with ATM interfaces with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-ATM2-MIB::ciscoatmSigEmitCldPtyEvents OID value, configure state conditions and alerts, and monitor any Cisco routers/switches with ATM interfaces from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.23 | ciscoAtm2MIB | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1 | ciscoatm2MIBObjects | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1 | ciscoatmSigStatTable | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1.1 | ciscoatmSigStatEntry | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1.1.14 | ciscoatmSigEmitCldPtyEvents | CISCO-ATM2-MIB |