All MIBs › CISCO-ATM2-MIB › ciscoatmSigDetectClgPtyEvents
ciscoatmSigDetectClgPtyEvents
Module: CISCO-ATM2-MIB
OID (symbolic): CISCO-ATM2-MIB::ciscoatmSigDetectClgPtyEvents
OID (numeric): 1.3.6.1.4.1.9.10.23.1.1.1.17
Node type: OBJECT-TYPE
Type: Counter32
Access: read-only
Description: Number of Calling Party Events detected on this interface. This counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only)
NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
What is ciscoatmSigDetectClgPtyEvents?
This counter monitors error events that occur due to the originating user doing something wrong, incrementing when a RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, or STATUS message with a matching cause code is received. Unlike the called-party events counter, this attributes call failures to a mistake made by the party originating the call, such as an invalid address format, so a rising count points troubleshooting toward the calling device's configuration rather than the network or the destination. A misconfigured CPE repeatedly sending malformed SETUP requests would drive up this counter without any corresponding network or called-party issue.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.23.1.1.1.17 snmpwalk -v2c -c public <target> CISCO-ATM2-MIB::ciscoatmSigDetectClgPtyEvents
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.23.1.1.1.17.1 snmpget -v2c -c public <target> CISCO-ATM2-MIB::ciscoatmSigDetectClgPtyEvents.1
SNMPv3 example:
snmpget -v3 -l authPriv -u snmpv3-user -a SHA -A "AuthPassword1" -x AES -X "PrivPassword1" <target> ciscoatmSigDetectClgPtyEvents.1
Start monitoring Cisco routers/switches with ATM interfaces with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-ATM2-MIB::ciscoatmSigDetectClgPtyEvents OID value, configure state conditions and alerts, and monitor any Cisco routers/switches with ATM interfaces from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.23 | ciscoAtm2MIB | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1 | ciscoatm2MIBObjects | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1 | ciscoatmSigStatTable | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1.1 | ciscoatmSigStatEntry | CISCO-ATM2-MIB |
| 1.3.6.1.4.1.9.10.23.1.1.1.17 | ciscoatmSigDetectClgPtyEvents | CISCO-ATM2-MIB |