All MIBs › Printer-MIB › prtInputMediaDimFeedDirChosen
prtInputMediaDimFeedDirChosen
Module: Printer-MIB
OID (symbolic): Printer-MIB::prtInputMediaDimFeedDirChosen
OID (numeric): 1.3.6.1.2.1.43.8.2.1.6
Node type: OBJECT-TYPE
Type: Integer32
Access: read-only
Description: The printer will act as if media of the chosen dimension (in the feed direction) is present in this input source. Note that this value will be used even if the input tray is empty. Feed dimension measurements are taken relative to the feed direction associated with that sub-unit and are in input sub-unit dimensional units (controlled by prtInputDimUnit, which uses PrtMediaUnitTC). If the printer supports the declared dimension,the granted dimension is the same as the declared dimension. If not, the granted dimension is set to the closest dimension that the printer supports when the declared dimension is set. The value (-1) means other and specifically indicates that this sub-unit places no restriction on this parameter. The value (-2)indicates unknown.
What is prtInputMediaDimFeedDirChosen?
This object specifies the media dimension (height or width) in the paper feed direction that the printer assumes is loaded in the input tray, measured in units defined by prtInputDimUnit. Even if the tray is empty, the printer uses this dimension for printing. Network print administrators use this to configure page size handling for automated paper selection.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.2.1.43.8.2.1.6 snmpwalk -v2c -c public <target> Printer-MIB::prtInputMediaDimFeedDirChosen
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.2.1.43.8.2.1.6.1 snmpget -v2c -c public <target> Printer-MIB::prtInputMediaDimFeedDirChosen.1
Start monitoring vendor-neutral, standards-based MIB, network-attached printers and MFPs from any vendor (RFC 3805) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Printer-MIB::prtInputMediaDimFeedDirChosen OID value, configure state conditions and alerts, and monitor any vendor-neutral, standards-based MIB, network-attached printers and MFPs from any vendor (RFC 3805) from a single console.
OID Breakdown
Upper-level ancestors (6 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.2 | mgmt | AXON-MIB |
| 1.3.6.1.2.1 | mib_2 | AXON-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.2.1.43 | printmib | Printer-MIB |
| 1.3.6.1.2.1.43.8 | prtInput | Printer-MIB |
| 1.3.6.1.2.1.43.8.2 | prtInputTable | Printer-MIB |
| 1.3.6.1.2.1.43.8.2.1 | prtInputEntry | Printer-MIB |
| 1.3.6.1.2.1.43.8.2.1.6 | prtInputMediaDimFeedDirChosen | Printer-MIB |