MRVINREACH (page 2 of 2) - SNMP MIB Browser

OID symbolic	OID numeric	Type	Access	Description
CTR ipxIfFramesIn	1.3.6.1.4.1.33.15.2.1.1.5	Counter	read-only	The number of IPX frames received on this interface.
CTR ipxIfFramesOut	1.3.6.1.4.1.33.15.2.1.1.6	Counter	read-only	The number of IPX frames sent on this interface.
CTR ipxIfErrors	1.3.6.1.4.1.33.15.2.1.1.7	Counter	read-only	The number of IPX errors seen on this interface.
INT ipxIfTransitDelay	1.3.6.1.4.1.33.15.2.1.1.8	INTEGER	read-write	The number of 55 millisecond ticks it takes for a packet to travel from one destination to another on the interface. A value of 0 means that the system will calculate this value based on the measured speed of the interface.
INT ipxIfTransitDelayActual	1.3.6.1.4.1.33.15.2.1.1.9	INTEGER	read-only	The number of 55 millisecond ticks it takes for a packet to travel from one destination to another on the interface.
INT ipxIfProtocolPriority	1.3.6.1.4.1.33.15.2.1.1.10	INTEGER	read-write	This value defines the priority at which all Internet Routed packets will be placed on the WAN output queue.
INT ipxIfWatchdogSpoof	1.3.6.1.4.1.33.15.2.1.1.11	INTEGER	read-write	Control for whether or not this router responds to IPX watchog requests on this interface.
INT ipxIfStatusNetwork	1.3.6.1.4.1.33.15.2.1.1.12	INTEGER	read-only	The IPX network number that is actually in use on the attached interface. This value may have been learned via listening to the attached network.
xIpxNetbios	1.3.6.1.4.1.33.15.3
INT ipxNetbiosHopLimit	1.3.6.1.4.1.33.15.3.1	INTEGER	read-write	Maximum number of hops that an IPX Netbios packet may make.
ipxNetbiosIfTable	1.3.6.1.4.1.33.15.3.2		not-accessible	A list of IPX interface entries.
ipxNetbiosIfEntry	1.3.6.1.4.1.33.15.3.2.1		not-accessible	IPX interface parameters and counters.
INT ipxNetbiosIfIndex	1.3.6.1.4.1.33.15.3.2.1.1	INTEGER	read-only	An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT ipxIfNetbiosForwarding	1.3.6.1.4.1.33.15.3.2.1.2	INTEGER	read-write	Control whether Netbios packet will be forwarded in or out on this interface.
CTR ipxIfNetbiosIn	1.3.6.1.4.1.33.15.3.2.1.3	Counter	read-only	The number of IPX Netbios frames received on this interface.
CTR ipxIfNetbiosOut	1.3.6.1.4.1.33.15.3.2.1.4	Counter	read-only	The number of IPX Netbios frames sent on this interface.
xIpxRip	1.3.6.1.4.1.33.15.4
ipxRipIfTable	1.3.6.1.4.1.33.15.4.1		not-accessible	A list of IPX interface entries.
ipxRipIfEntry	1.3.6.1.4.1.33.15.4.1.1		not-accessible	IPX interface parameters and counters.
INT ipxRipIfIndex	1.3.6.1.4.1.33.15.4.1.1.1	INTEGER	read-only	An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT ipxIfRipBcst	1.3.6.1.4.1.33.15.4.1.1.2	INTEGER	read-write	Control whether RIP packets will be broadcasted out this interface.
INT ipxIfRipBcstDiscardTimeout	1.3.6.1.4.1.33.15.4.1.1.3	INTEGER	read-write	The number of seconds to wait before discarding information learned from a RIP broadcast.
INT ipxIfRipBcstTimer	1.3.6.1.4.1.33.15.4.1.1.4	INTEGER	read-write	The number of seconds to wait between sending out RIP broadcasts.
CTR ipxIfRipIn	1.3.6.1.4.1.33.15.4.1.1.5	Counter	read-only	The number of RIP broadcasts received on this interface.
CTR ipxIfRipOut	1.3.6.1.4.1.33.15.4.1.1.6	Counter	read-only	The number of RIP broadcasts sent on this interface.
CTR ipxIfRipAgedOut	1.3.6.1.4.1.33.15.4.1.1.7	Counter	read-only	The number of entries timed out and discarded on this interface.
ipxRipTable	1.3.6.1.4.1.33.15.4.2		not-accessible	A list of RIP entries.
ipxRipEntry	1.3.6.1.4.1.33.15.4.2.1		not-accessible	IPX interface parameters and counters.
INT ipxRipNetwork	1.3.6.1.4.1.33.15.4.2.1.1	INTEGER	read-only	An IPX network number to which this router knows a path.
OCT ipxRipRouter	1.3.6.1.4.1.33.15.4.2.1.2	OCTET STRING	read-only	The Ethernet address of an IPX router on this network.
INT ipxRipInterface	1.3.6.1.4.1.33.15.4.2.1.3	INTEGER	read-only	The interface to reach the router. A value of ifIndex.
INT ipxRipHops	1.3.6.1.4.1.33.15.4.2.1.4	INTEGER	read-only	The number of hops to reach the router.
INT ipxRipTransTime	1.3.6.1.4.1.33.15.4.2.1.5	INTEGER	read-only	The number of 55 millisecond ticks it takes for a packet to travel to the router.
INT ipxRipAge	1.3.6.1.4.1.33.15.4.2.1.6	INTEGER	read-only	The age of the RIP entry in seconds.
ipxRipRtTable	1.3.6.1.4.1.33.15.4.3		not-accessible	A list of RIP Routing entries.
ipxRipRtEntry	1.3.6.1.4.1.33.15.4.3.1		not-accessible	IPX Routing Entry information
INT ipxRipRtNetwork	1.3.6.1.4.1.33.15.4.3.1.1	INTEGER	read-only	An IPX network number to which this router knows a path.
OCT ipxRipRtRouter	1.3.6.1.4.1.33.15.4.3.1.2	OCTET STRING	read-only	The Ethernet address of an IPX router on this network.
INT ipxRipRtInterface	1.3.6.1.4.1.33.15.4.3.1.3	INTEGER	read-only	The interface to reach the router. A value of ifIndex.
INT ipxRipRtHops	1.3.6.1.4.1.33.15.4.3.1.4	INTEGER	read-write	The number of hops to reach the router.
INT ipxRipRtTransTime	1.3.6.1.4.1.33.15.4.3.1.5	INTEGER	read-write	The number of 55 millisecond ticks it takes for a packet to travel to the router.
INT ipxRipRtOrigin	1.3.6.1.4.1.33.15.4.3.1.6	INTEGER	read-only	The source of the RIP entry, either Learned via RIP or Static.
INT ipxRipRtRowStatus	1.3.6.1.4.1.33.15.4.3.1.7	INTEGER	read-write	Create or Delete RIP routing table entries.
xIpxSap	1.3.6.1.4.1.33.15.5
ipxSapIfTable	1.3.6.1.4.1.33.15.5.1		not-accessible	A list of IPX interface entries.
ipxSapIfEntry	1.3.6.1.4.1.33.15.5.1.1		not-accessible	IPX interface parameters and counters.
INT ipxSapIfIndex	1.3.6.1.4.1.33.15.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT ipxIfSapBcst	1.3.6.1.4.1.33.15.5.1.1.2	INTEGER	read-write	Control whether SAP packets will be broadcasted out this interface.
INT ipxIfSapBcstDiscardTimeout	1.3.6.1.4.1.33.15.5.1.1.3	INTEGER	read-write	The number of seconds to wait before discarding information learned from a SAP broadcast.
INT ipxIfSapBcstTimer	1.3.6.1.4.1.33.15.5.1.1.4	INTEGER	read-write	The number of seconds to wait between sending out SAP broadcasts.
CTR ipxIfSapIn	1.3.6.1.4.1.33.15.5.1.1.5	Counter	read-only	The number SAP broadcasts received on this interface.
CTR ipxIfSapOut	1.3.6.1.4.1.33.15.5.1.1.6	Counter	read-only	The number SAP broadcasts sent on this interface.
CTR ipxIfSapAgedOut	1.3.6.1.4.1.33.15.5.1.1.7	Counter	read-only	The number entries for this interface discarded due to aging timeout.
ipxSapTable	1.3.6.1.4.1.33.15.5.2		not-accessible	A list of SAP entries.
ipxSapEntry	1.3.6.1.4.1.33.15.5.2.1		not-accessible	IPX interface parameters and counters.
STR ipxSapName	1.3.6.1.4.1.33.15.5.2.1.1	DisplayString	read-only	The name of the service, null filled.
INT ipxSapNetwork	1.3.6.1.4.1.33.15.5.2.1.2	INTEGER	read-only	The IPX network number on which the service's host resides.
OCT ipxSapHost	1.3.6.1.4.1.33.15.5.2.1.3	OCTET STRING	read-only	The Ethernet address of the IPX host of the service.
INT ipxSapSocket	1.3.6.1.4.1.33.15.5.2.1.4	INTEGER	read-only	The socket number of the service on the host.
INT ipxSapInterface	1.3.6.1.4.1.33.15.5.2.1.5	INTEGER	read-only	The interface of the router in the direction of the service. A value of ifIndex.
INT ipxSapType	1.3.6.1.4.1.33.15.5.2.1.6	INTEGER	read-only	The type of the service. The enumeration is an incomplete set of all possible values.
INT ipxSapAge	1.3.6.1.4.1.33.15.5.2.1.7	INTEGER	read-only	The age of the Sap entry in seconds.
ipxSapSvTable	1.3.6.1.4.1.33.15.5.3		not-accessible	A list of SAP entries.
ipxSapSvEntry	1.3.6.1.4.1.33.15.5.3.1		not-accessible	IPX interface parameters and counters.
STR ipxSapSvName	1.3.6.1.4.1.33.15.5.3.1.1	DisplayString	read-only	The name of the service.
INT ipxSapSvNetwork	1.3.6.1.4.1.33.15.5.3.1.2	INTEGER	read-only	The IPX network number on which the service's host resides.
OCT ipxSapSvHost	1.3.6.1.4.1.33.15.5.3.1.3	OCTET STRING	read-only	The Ethernet address of the IPX host of the service.
INT ipxSapSvSocket	1.3.6.1.4.1.33.15.5.3.1.4	INTEGER	read-only	The socket number of the service on the host.
INT ipxSapSvInterface	1.3.6.1.4.1.33.15.5.3.1.5	INTEGER	read-only	The interface of the router in the direction of the service. A value of ifIndex.
INT ipxSapSvOrigin	1.3.6.1.4.1.33.15.5.3.1.6	INTEGER	read-only	The source of the RIP entry, either Learned via RIP or Static.
INT ipxSapSvType	1.3.6.1.4.1.33.15.5.3.1.7	INTEGER	read-only	The type of the service. The enumeration is an incomplete set of all possible values.
INT ipxSapSvHops	1.3.6.1.4.1.33.15.5.3.1.8	INTEGER	read-write	The number of hops to the Service.
INT ipxSapSvRowStatus	1.3.6.1.4.1.33.15.5.3.1.9	INTEGER	read-write	Create or Delete SAP Service table entries.
INT ipxSapSvAge	1.3.6.1.4.1.33.15.5.3.1.10	INTEGER	read-only	The age of the Sap entry in seconds.
xIpxFilter	1.3.6.1.4.1.33.15.6
ipxIfFilterTable	1.3.6.1.4.1.33.15.6.1		not-accessible	A list of IPX interface Source and Destination address Filter entries.
ipxIfFilterEntry	1.3.6.1.4.1.33.15.6.1.1		not-accessible	IPX Source and Destination interface Filters.
INT ipxIfFilterIndex	1.3.6.1.4.1.33.15.6.1.1.1	INTEGER	read-only	The interface to which this IPX Address filter applies. A value of ifIndex.
INT ipxIfFilterDestNetwork	1.3.6.1.4.1.33.15.6.1.1.2	INTEGER	read-only	The destination IPX network to be filtered.
OCT ipxIfFilterDestNode	1.3.6.1.4.1.33.15.6.1.1.3	OCTET STRING	read-only	The destination IPX node to be filtered.
INT ipxIfFilterSourceNetwork	1.3.6.1.4.1.33.15.6.1.1.4	INTEGER	read-only	The destination IPX network to be filtered.
OCT ipxIfFilterSourceNode	1.3.6.1.4.1.33.15.6.1.1.5	OCTET STRING	read-only	The destination IPX node to be filtered.
INT ipxIfFilterPacketType	1.3.6.1.4.1.33.15.6.1.1.6	INTEGER	read-only	The IPX packet type to be filtered.
INT ipxIfFilterAction	1.3.6.1.4.1.33.15.6.1.1.7	INTEGER	read-write	The IPX filter action to be taken, either Forward or Discard.
INT ipxIfFilterRowStatus	1.3.6.1.4.1.33.15.6.1.1.8	INTEGER	read-write	The IPX Filter create or delete function.
INT ipxIfFilterStatusDestNetworkAll	1.3.6.1.4.1.33.15.6.1.1.9	INTEGER	read-only	The IPX Filter flag meaning ALL destination networks.
INT ipxIfFilterStatusDestNodeAll	1.3.6.1.4.1.33.15.6.1.1.10	INTEGER	read-only	The IPX Filter flag meaning ALL destination nodes.
INT ipxIfFilterStatusSourceNetworkAll	1.3.6.1.4.1.33.15.6.1.1.11	INTEGER	read-only	The IPX Filter flag meaning ALL source networks.
INT ipxIfFilterStatusSourceNodeAll	1.3.6.1.4.1.33.15.6.1.1.12	INTEGER	read-only	The IPX Filter flag meaning ALL source nodes.
INT ipxIfFilterStatusPacketTypeAll	1.3.6.1.4.1.33.15.6.1.1.13	INTEGER	read-only	The IPX Filter flag meaning ALL packet types.
ipxIfRipFilterTable	1.3.6.1.4.1.33.15.6.2		not-accessible	A list of IPX interface RIP Filter entries.
ipxIfRipFilterEntry	1.3.6.1.4.1.33.15.6.2.1		not-accessible	IPX RIP interface Filters.
INT ipxIfRipFilterNetwork	1.3.6.1.4.1.33.15.6.2.1.1	INTEGER	read-only	The IPX RIP network to be filtered.
INT ipxIfRipFilterType	1.3.6.1.4.1.33.15.6.2.1.2	INTEGER	read-only	The IPX RIP filter type, either IMPORT or EXPORT.
INT ipxIfRipFilterAction	1.3.6.1.4.1.33.15.6.2.1.3	INTEGER	read-write	The IPX RIP filter action to be taken, either ALLOW or DENY.
INT ipxIfRipFilterRowStatus	1.3.6.1.4.1.33.15.6.2.1.4	INTEGER	read-write	The IPX RIP Filter create or delete function.
INT ipxIfRipFilterNetworkAll	1.3.6.1.4.1.33.15.6.2.1.5	INTEGER	read-only	The IPX RIP Filter flag meaning filter ALL networks.
OCT ipxIfRipFilterHost	1.3.6.1.4.1.33.15.6.2.1.6	OCTET STRING	read-only	The RIP Filter IPX Host Address from which RIP will ALLOW/DENY IMPORT of routes.
ipxIfSapFilterTable	1.3.6.1.4.1.33.15.6.3		not-accessible	A list of IPX interface SAP Filter entries.
ipxIfSapFilterEntry	1.3.6.1.4.1.33.15.6.3.1		not-accessible	IPX SAP interface Filters.
INT ipxIfSapFilterNetwork	1.3.6.1.4.1.33.15.6.3.1.1	INTEGER	read-only	The IPX SAP network to be filtered.
INT ipxIfSapFilterType	1.3.6.1.4.1.33.15.6.3.1.2	INTEGER	read-only	The IPX SAP filter type, either IMPORT or EXPORT.
INT ipxIfSapFilterServiceType	1.3.6.1.4.1.33.15.6.3.1.3	INTEGER	read-only	The IPX SAP service type to which this filter applies.
INT ipxIfSapFilterAction	1.3.6.1.4.1.33.15.6.3.1.4	INTEGER	read-write	The IPX SAP filter action to be taken, either ALLOW or DENY.
INT ipxIfSapFilterRowStatus	1.3.6.1.4.1.33.15.6.3.1.5	INTEGER	read-write	The IPX SAP Filter create or delete function.
INT ipxIfSapFilterNetworkAll	1.3.6.1.4.1.33.15.6.3.1.6	INTEGER	read-only	The IPX SAP Filter flag meaning filter ALL networks.
INT ipxIfSapFilterServiceTypeAll	1.3.6.1.4.1.33.15.6.3.1.7	INTEGER	read-only	The IPX SAP Filter flag meaning filter ALL service types.
STR ipxIfSapFilterName	1.3.6.1.4.1.33.15.6.3.1.8	DisplayString	read-only	The name of the service to be filtered.
OCT ipxIfSapFilterHost	1.3.6.1.4.1.33.15.6.3.1.9	OCTET STRING	read-only	The IPX Host address from which SAP will ALLOW/DENY IMPORT of services .
xIpxPrinter	1.3.6.1.4.1.33.15.8
ipxPrinterPortTable	1.3.6.1.4.1.33.15.8.1		not-accessible	A list of IPX printer character port entries.
ipxPrinterPortEntry	1.3.6.1.4.1.33.15.8.1.1		not-accessible	IPX printer parameter values for a character port.
INT ipxPrinterPortIndex	1.3.6.1.4.1.33.15.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
INT ipxPrinterPortStatus	1.3.6.1.4.1.33.15.8.1.1.2	INTEGER	read-write	Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
STR ipxPrinterPortServer	1.3.6.1.4.1.33.15.8.1.1.3	DisplayString	read-write	The name of an active print server on the network.
INT ipxPrinterPortPrinter	1.3.6.1.4.1.33.15.8.1.1.4	INTEGER	read-write	An available remote printer on ixpPrinterPortServer.
INT ipxTimeout	1.3.6.1.4.1.33.15.8.1.1.5	INTEGER	read-write	A control to set the the time at which a print job from a print server will be timed out and the port freed.
INT ipxPrinterEthernet	1.3.6.1.4.1.33.15.8.2	INTEGER	read-write	Control for use of Ethernet-style message framing, with the IPX protocol type. Mutually exclusive with ipxPrinterMac, ipxPrinterMac802_2_Snap, and ipxPrinterMac802_2.
INT ipxPrinterMac	1.3.6.1.4.1.33.15.8.3	INTEGER	read-write	Control for use of MAC-only message framing, with no protocol type. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac802_2_Snap, and ipxPrinterMac802_2.
INT ipxPrinterMac802_2	1.3.6.1.4.1.33.15.8.4	INTEGER	read-write	Control for use of MAC message framing with 802.2 framing. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac, and ipxPrinterMac802_2_Snap.
INT ipxPrinterMac802_2_Snap	1.3.6.1.4.1.33.15.8.5	INTEGER	read-write	Control for use of MAC-only message framing with 802 Snap framing. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac, and ipxPrinterMac802_2.
xChassis	1.3.6.1.4.1.33.16
xChassisBasic	1.3.6.1.4.1.33.16.1
MAC basicBase802Address	1.3.6.1.4.1.33.16.1.1	MacAddress	read-only	Base IEEE 802 global address for the chassis.
INT basicSlot	1.3.6.1.4.1.33.16.1.2	INTEGER	read-only	Chassis slot number (slotIndex) of the system whose agent is supplying this MIB.
INT basicSlotNumber	1.3.6.1.4.1.33.16.1.3	INTEGER	read-only	Number of slots in the chassis.
MAC basicNewBase802Address	1.3.6.1.4.1.33.16.1.4	MacAddress	read-write	New base IEEE 802 global address for the chassis. Must be set in conjunction with featType 'changeEthernetAddress' and featKey from the MRV In-Reach System MIB.
xSegment	1.3.6.1.4.1.33.16.2
segmentTable	1.3.6.1.4.1.33.16.2.1		not-accessible	A list of segment entries, one for each segment of each type on the chassis.
segmentEntry	1.3.6.1.4.1.33.16.2.1.1		not-accessible	Values for a chassis segment.
NET segmentType	1.3.6.1.4.1.33.16.2.1.1.1	NetworkType	read-only	The segment type.
LET segmentIndex	1.3.6.1.4.1.33.16.2.1.1.2	Letter	read-only	An index value that uniquely identifies a segment.
xPort	1.3.6.1.4.1.33.16.3
IOT portIOCardType	1.3.6.1.4.1.33.16.3.1	IOType	read-only	The hardware type of the I/O card in this slot.
SER portIOCardSerialNumber	1.3.6.1.4.1.33.16.3.2	SerialNumber	read-only	The MRV In-Reach serial number of the I/O card in this slot.
INT portIOCardOperStatus	1.3.6.1.4.1.33.16.3.3	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
portTable	1.3.6.1.4.1.33.16.3.4		not-accessible	A list of port entries, one for each port of each type on the slots I/O card.
portEntry	1.3.6.1.4.1.33.16.3.4.1		not-accessible	Values for an I/O card port.
NET portType	1.3.6.1.4.1.33.16.3.4.1.1	NetworkType	read-only	The port type.
INT portIndex	1.3.6.1.4.1.33.16.3.4.1.2	INTEGER	read-only	An index value that uniquely identifies a port.
xController	1.3.6.1.4.1.33.16.4
controllerTable	1.3.6.1.4.1.33.16.4.1		not-accessible	A list of controller entries, one for each controller of each type on the local system.
controllerEntry	1.3.6.1.4.1.33.16.4.1.1		not-accessible	Values for a controller.
NET controllerType	1.3.6.1.4.1.33.16.4.1.1.1	NetworkType	read-only	The controller type.
INT controllerIndex	1.3.6.1.4.1.33.16.4.1.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID controllerNetwork	1.3.6.1.4.1.33.16.4.1.1.3	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this controller is to use, that is, segmentType, portType or controllerType.
xInterface	1.3.6.1.4.1.33.16.5
interfaceTable	1.3.6.1.4.1.33.16.5.1		not-accessible	A list of interface entries, corresponding to the MIB II Interface group. These are directly equivalent to hardware network controllers, and must be the lowest numbered interfaces on the system.
interfaceEntry	1.3.6.1.4.1.33.16.5.1.1		not-accessible	Values for an interface.
INT interfaceIndex	1.3.6.1.4.1.33.16.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID interfaceNetwork	1.3.6.1.4.1.33.16.5.1.1.2	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this interface is to use, that is, segmentType, portType, or controllerType.
xSlotBootControl	1.3.6.1.4.1.33.16.6
slotBootControlTable	1.3.6.1.4.1.33.16.6.1		not-accessible	A list of slot boot control entries.
slotBootControlEntry	1.3.6.1.4.1.33.16.6.1.1		not-accessible	Values for a chassis slot.
INT slotBootControlSlot	1.3.6.1.4.1.33.16.6.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlIndex	1.3.6.1.4.1.33.16.6.1.1.2	INTEGER	read-only	An index value that uniquely identifies a boot control entry, from 1 to the number of entries for the slot.
INT slotBootControlStatus	1.3.6.1.4.1.33.16.6.1.1.3	INTEGER	read-write	The status of the entry. Set to 'disabled' to disable the entry.
OID slotBootControlController	1.3.6.1.4.1.33.16.6.1.1.4	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the controller this entry selects for bootstrap operation, that is, controllerType. This entry must be compatible with slotBootControlNetwork, including being of the same network type. The value 0.0 indicates default action.
OID slotBootControlNetwork	1.3.6.1.4.1.33.16.6.1.1.5	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment or port this entry selects for bootstrap operation, that is, segmentType or portType. This entry must be compatible with slotBootControlController, including being of the same network type. The value 0.0 indicates default action.
STR slotBootControlMopFile	1.3.6.1.4.1.33.16.6.1.1.6	DisplayString	read-write	The software file name to request for down-line load of the server via MOP or XMOP.
STR slotBootControlInternetFile	1.3.6.1.4.1.33.16.6.1.1.7	DisplayString	read-write	The filename to request when loading an image via TFTP.
IP slotBootControlInternetAddress	1.3.6.1.4.1.33.16.6.1.1.8	IpAddress	read-write	The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetServer	1.3.6.1.4.1.33.16.6.1.1.9	IpAddress	read-write	The internet address of the server to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetGateway	1.3.6.1.4.1.33.16.6.1.1.10	IpAddress	read-write	The internet address of the gateway to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
STR slotBootControlInternetDelimiter	1.3.6.1.4.1.33.16.6.1.1.11	DisplayString	read-write	The character separating the load file directory name from the file name.
slotBootControlFlagTable	1.3.6.1.4.1.33.16.6.2		not-accessible	A list of slot boot control source flag entries.
slotBootControlFlagEntry	1.3.6.1.4.1.33.16.6.2.1		not-accessible	Values for a boot control flag.
INT slotBootControlFlagLoadBootpTftp	1.3.6.1.4.1.33.16.6.2.1.1	INTEGER	read-write	Control for performing load over BOOTP/TFTP.
INT slotBootControlFlagParamBootpTftp	1.3.6.1.4.1.33.16.6.2.1.2	INTEGER	read-write	Control for performing parameter load over BOOTP/TFTP.
INT slotBootControlFlagDumpBootpTftp	1.3.6.1.4.1.33.16.6.2.1.3	INTEGER	read-write	Control for performing dump over BOOTP/TFTP.
INT slotBootControlFlagLoadTftpDirect	1.3.6.1.4.1.33.16.6.2.1.4	INTEGER	read-write	Control for performing load over direct TFTP.
INT slotBootControlFlagParamTftpDirect	1.3.6.1.4.1.33.16.6.2.1.5	INTEGER	read-write	Control for performing parameter load over direct TFTP.
INT slotBootControlFlagDumpTftpDirect	1.3.6.1.4.1.33.16.6.2.1.6	INTEGER	read-write	Control for performing dump over direct TFTP.
INT slotBootControlFlagLoadLocal	1.3.6.1.4.1.33.16.6.2.1.7	INTEGER	read-write	Control for performing load from a local device.
INT slotBootControlFlagParamLocal	1.3.6.1.4.1.33.16.6.2.1.8	INTEGER	read-write	Control for performing parameter load from a local device.
INT slotBootControlFlagDumpLocal	1.3.6.1.4.1.33.16.6.2.1.9	INTEGER	read-write	Control for performing dump from a local device.
INT slotBootControlFlagLoadMop	1.3.6.1.4.1.33.16.6.2.1.10	INTEGER	read-write	Control for performing load over Digital's MOP.
INT slotBootControlFlagParamMop	1.3.6.1.4.1.33.16.6.2.1.11	INTEGER	read-write	Control for performing parameter load over Digital's MOP.
INT slotBootControlFlagDumpMop	1.3.6.1.4.1.33.16.6.2.1.12	INTEGER	read-write	Control for performing dump over Digital's MOP.
INT slotBootControlFlagLoadXmop	1.3.6.1.4.1.33.16.6.2.1.13	INTEGER	read-write	Control for performing load over MRV In-Reach extended MOP.
INT slotBootControlFlagParamXmop	1.3.6.1.4.1.33.16.6.2.1.14	INTEGER	read-write	Control for performing parameter load over MRV In-Reach extended MOP.
INT slotBootControlFlagDumpXmop	1.3.6.1.4.1.33.16.6.2.1.15	INTEGER	read-write	Control for performing dump over MRV In-Reach extended MOP.
INT slotBootControlFlagLoadRarpTftp	1.3.6.1.4.1.33.16.6.2.1.16	INTEGER	read-write	Control for performing load over RARP/TFTP.
INT slotBootControlFlagParamRarpTftp	1.3.6.1.4.1.33.16.6.2.1.17	INTEGER	read-write	Control for performing parameter load over RARP/TFTP.
INT slotBootControlFlagDumpRarpTftp	1.3.6.1.4.1.33.16.6.2.1.18	INTEGER	read-write	Control for performing dump over RARP/TFTP.
slotBootControlStorageTable	1.3.6.1.4.1.33.16.6.3		not-accessible	A list of slot boot control Storage entries.
slotBootControlStorageEntry	1.3.6.1.4.1.33.16.6.3.1		not-accessible	Values for a chassis slot.
INT slotBootControlStorageClientSlot	1.3.6.1.4.1.33.16.6.3.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlStorageServerSlot	1.3.6.1.4.1.33.16.6.3.1.2	INTEGER	read-only	An index value that uniquely identifies the slot in which the Storage record resides, with the same values as slotIndex.
INT slotBootControlStorageStatus	1.3.6.1.4.1.33.16.6.3.1.3	INTEGER	read-only	The status of the entry.
CTR slotBootControlStorageFailures	1.3.6.1.4.1.33.16.6.3.1.4	Counter	read-only	The number of times a read from or write to a given Storage location failed
xSlot	1.3.6.1.4.1.33.16.7
slotTable	1.3.6.1.4.1.33.16.7.1		not-accessible	A list of slot entries.
slotEntry	1.3.6.1.4.1.33.16.7.1.1		not-accessible	Values for a chassis slot.
INT slotIndex	1.3.6.1.4.1.33.16.7.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as basicSlot. As the objects found at instance zero are duplicates, that instance does not appear in responses a get-next, that is, the lowest numbered slotIndex returned by get-next is 1.
INT slotAdminAction	1.3.6.1.4.1.33.16.7.1.1.2	INTEGER	read-write	Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of slotOperStatus.
INT slotOperStatus	1.3.6.1.4.1.33.16.7.1.1.3	INTEGER	read-only	Relative to the chassis, the current operating status of the system in the slot.
GAU slotSecondsSinceReset	1.3.6.1.4.1.33.16.7.1.1.4	Gauge	read-only	The number of seconds since the system in the slot was last reset by hardware or software.
HAR slotHardwareType	1.3.6.1.4.1.33.16.7.1.1.5	HardwareType	read-only	The type of hardware in the slot.
SER slotHardwareSerialNumber	1.3.6.1.4.1.33.16.7.1.1.6	SerialNumber	read-only	The MRV In-Reach serial number of the function card hardware in this slot.
INT slotHardwareRevision	1.3.6.1.4.1.33.16.7.1.1.7	INTEGER	read-only	This revision level of the function card hardware in the slot.
IOT slotIOCardType	1.3.6.1.4.1.33.16.7.1.1.8	IOType	read-only	The hardware type of the I/O card in this slot.
SER slotIOCardSerialNumber	1.3.6.1.4.1.33.16.7.1.1.9	SerialNumber	read-only	The MRV In-Reach serial number of the I/O card in this slot.
INT slotIOCardOperStatus	1.3.6.1.4.1.33.16.7.1.1.10	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
INT slotBootstrapFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.11	INTEGER	read-only	The firmware revision level of the bootstrap ROM installed in the system in the slot.
INT slotElementalFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.12	INTEGER	read-only	The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot.
INT slotMemorySize	1.3.6.1.4.1.33.16.7.1.1.13	INTEGER	read-only	The number of bytes of memory installed in the system in the slot.
GAU slotLedNumber	1.3.6.1.4.1.33.16.7.1.1.14	Gauge	read-only	The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable.
OCT slotLedStatus	1.3.6.1.4.1.33.16.7.1.1.15	OCTET STRING	read-only	The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the first byte of the value, proceeding to the low-order bit, then to then next byte. On the system hardware, the first LED is at the top, left, front, proceeding left to right, top to bottom, and front to back.
MAC slotBase802Address	1.3.6.1.4.1.33.16.7.1.1.16	MacAddress	read-only	Base IEEE 802 global address for the slot.
IP slotIpAddress	1.3.6.1.4.1.33.16.7.1.1.17	IpAddress	read-only	An internet address to which the system in this slot might respond. May be one of many.
INT slotPlus5Status	1.3.6.1.4.1.33.16.7.1.1.18	INTEGER	read-only	Status of the +5 volt power to the slot.
INT slotPlus12Status	1.3.6.1.4.1.33.16.7.1.1.19	INTEGER	read-only	Status of the +12 volt power to the slot.
INT slotMinus12Status	1.3.6.1.4.1.33.16.7.1.1.20	INTEGER	read-only	Status of the -12 volt power to the slot.
GAU slotPlus5Watts	1.3.6.1.4.1.33.16.7.1.1.21	Gauge	read-only	Tenths of watts of +5 volt power currently drawn by the slot.
GAU slotPlus12Watts	1.3.6.1.4.1.33.16.7.1.1.22	Gauge	read-only	Tenths of watts of +12 volt power currently drawn by the slot.
GAU slotMinus12Watts	1.3.6.1.4.1.33.16.7.1.1.23	Gauge	read-only	Tenths of watts of -12 volt power currently drawn by the slot.
INT slotIOCardHardwareVersion	1.3.6.1.4.1.33.16.7.1.1.24	INTEGER	read-only	Version number of I/O card in the slot.
INT slotRestoreNVS	1.3.6.1.4.1.33.16.7.1.1.25	INTEGER	read-write	Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' has no effect.
INT slotDefaultNVS	1.3.6.1.4.1.33.16.7.1.1.26	INTEGER	read-write	Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect.
slotBootTable	1.3.6.1.4.1.33.16.7.2		not-accessible	A list of slot bootstrap status entries. A given slot has an entry in this table only when slotOperStatus is one of: loadRequested, loading, dumpRequested, dumping, paramRequested, paramLoading
slotBootEntry	1.3.6.1.4.1.33.16.7.2.1		not-accessible	Bootstrap status values for a chassis slot.
INT slotBootIndex	1.3.6.1.4.1.33.16.7.2.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootIfIndex	1.3.6.1.4.1.33.16.7.2.1.2	INTEGER	read-only	An index value that uniquely identifies the interface in use for bootstrap functions. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID slotBootNetwork	1.3.6.1.4.1.33.16.7.2.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this interface is using, that is, segmentType or portType.
INT slotBootProtocol	1.3.6.1.4.1.33.16.7.2.1.4	INTEGER	read-only	The protocol in use for bootstrap operation.
MAC slotBoot802Address	1.3.6.1.4.1.33.16.7.2.1.5	MacAddress	read-only	IEEE 802 global address in use for bootstrap operation.
ADR slotBootAddressType	1.3.6.1.4.1.33.16.7.2.1.6	AddressType	read-only	The type of network address contained in slotBootAddress.
OCT slotBootAddress	1.3.6.1.4.1.33.16.7.2.1.7	OCTET STRING	read-only	The network address the system in the slot is using to identify itself for bootstrap operation.
ADR slotBootServerAddressType	1.3.6.1.4.1.33.16.7.2.1.8	AddressType	read-only	The type of network address contained in slotBootServerAddress.
OCT slotBootServerAddress	1.3.6.1.4.1.33.16.7.2.1.9	OCTET STRING	read-only	The network address of the system supplying bootstrap services to the system in the slot.
IP slotBootGatewayAddress	1.3.6.1.4.1.33.16.7.2.1.10	IpAddress	read-only	The internet address of the router in use for bootstrap operation.
STR slotBootFileName	1.3.6.1.4.1.33.16.7.2.1.11	DisplayString	read-only	The full name of the file in use for bootstrap operation.
GAU slotBootBlockNumber	1.3.6.1.4.1.33.16.7.2.1.12	Gauge	read-only	The current block number being transferred for bootstrap operation, zero if unknown or not applicable.
OCT slotBootCrashCode	1.3.6.1.4.1.33.16.7.2.1.13	OCTET STRING	read-only	If slotOperStatus is dumpRequested or dumping, a code number to identify the crash reason; otherwise zero length.
slotControllerTable	1.3.6.1.4.1.33.16.7.3		not-accessible	A list of controller entries, one for each controller of each type in each slot.
slotControllerEntry	1.3.6.1.4.1.33.16.7.3.1		not-accessible	Values for a controller.
NET slotControllerType	1.3.6.1.4.1.33.16.7.3.1.1	NetworkType	read-only	The controller type.
INT slotControllerIndex	1.3.6.1.4.1.33.16.7.3.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID slotControllerNetwork	1.3.6.1.4.1.33.16.7.3.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this controller is to use, that is, segmentType or portType.
xPowerSupply	1.3.6.1.4.1.33.16.8
powerSupplyTable	1.3.6.1.4.1.33.16.8.1		not-accessible	A list of power supply entries.
powerSupplyEntry	1.3.6.1.4.1.33.16.8.1.1		not-accessible	Values for a chassis power supply.
INT powerSupplyIndex	1.3.6.1.4.1.33.16.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a power supply, in the range 1 to the number of power supply slots in the chassis.
INT powerSupplyAdminAction	1.3.6.1.4.1.33.16.8.1.1.2	INTEGER	read-write	Control to cause reset of the power supply. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of powerSupplyRedundancyStatus.
INT powerSupplyFirmwareVersion	1.3.6.1.4.1.33.16.8.1.1.3	INTEGER	read-only	Version number of power supply firmware.
INT powerSupplyRedundancyStatus	1.3.6.1.4.1.33.16.8.1.1.4	INTEGER	read-only	The current redundancy status of the power supply.
INT powerSupplyPlus5Status	1.3.6.1.4.1.33.16.8.1.1.5	INTEGER	read-only	Status of the +5 volt power from the power supply.
INT powerSupplyPlus12Status	1.3.6.1.4.1.33.16.8.1.1.6	INTEGER	read-only	Status of the +12 volt power from the power supply.
INT powerSupplyMinus12Status	1.3.6.1.4.1.33.16.8.1.1.7	INTEGER	read-only	Status of the -12 volt power from the power supply.
INT powerSupplyThermalWarningStatus	1.3.6.1.4.1.33.16.8.1.1.8	INTEGER	read-only	The current thermal warning status of the power supply.
INT powerSupplyThermalShutdownStatus	1.3.6.1.4.1.33.16.8.1.1.9	INTEGER	read-only	The current thermal shutdown status of the power supply.
INT powerSupplyFanStatus	1.3.6.1.4.1.33.16.8.1.1.10	INTEGER	read-only	The current status of the power supply's fan.
INT powerSupplyHardwareInhibitStatus	1.3.6.1.4.1.33.16.8.1.1.11	INTEGER	read-only	The current status of the power supply's hardware inhibit.
INT powerSupplyPlus5History	1.3.6.1.4.1.33.16.8.1.1.12	INTEGER	read-only	History of the +5 volt power from the power supply.
INT powerSupplyPlus12History	1.3.6.1.4.1.33.16.8.1.1.13	INTEGER	read-only	History of the +12 volt power from the power supply.
INT powerSupplyMinus12History	1.3.6.1.4.1.33.16.8.1.1.14	INTEGER	read-only	History of the -12 volt power from the power supply.
INT powerSupplyThermalWarningHistory	1.3.6.1.4.1.33.16.8.1.1.15	INTEGER	read-only	The thermal warning history of the power supply.
INT powerSupplyThermalShutdownHistory	1.3.6.1.4.1.33.16.8.1.1.16	INTEGER	read-only	The thermal shutdown history of the power supply.
INT powerSupplyFanHistory	1.3.6.1.4.1.33.16.8.1.1.17	INTEGER	read-only	The status history of the power supply's fan.
INT powerSupplyHardwareInhibitHistory	1.3.6.1.4.1.33.16.8.1.1.18	INTEGER	read-only	The status history of the power supply's hardware inhibit.
GAU powerSupplyPlus5Volts	1.3.6.1.4.1.33.16.8.1.1.19	Gauge	read-only	In hundredths, volts of +5 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyPlus12Volts	1.3.6.1.4.1.33.16.8.1.1.20	Gauge	read-only	In hundredths, volts of +12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyMinus12Volts	1.3.6.1.4.1.33.16.8.1.1.21	Gauge	read-only	In hundredths, volts of -12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyWatts	1.3.6.1.4.1.33.16.8.1.1.22	Gauge	read-only	Watts of power currently drawn from this power supply. A value of 0 indicates unknown.
GAU powerSupplyWattsMax	1.3.6.1.4.1.33.16.8.1.1.23	Gauge	read-only	Maximum watts of power available from this power supply. A value of 0 indicates unknown.
GAU powerSupplyChassisWatts	1.3.6.1.4.1.33.16.8.1.1.24	Gauge	read-only	Total watts of power currently drawn by the entire chassis. A value of 0 indicates unknown.
GAU powerSupplyChassisWattsMax	1.3.6.1.4.1.33.16.8.1.1.25	Gauge	read-only	Total maximum watts of power available from all the power supplies in the chassis. A value of 0 indicates unknown.
INT powerSupplyHardwareType	1.3.6.1.4.1.33.16.8.1.1.26	INTEGER	read-only	The type of power supply.
xFirmwareUpdate	1.3.6.1.4.1.33.16.9
firmwareUpdateTable	1.3.6.1.4.1.33.16.9.1		not-accessible	Table of descriptive and status information concerning the writing of firmware to a target I/O card.
firmwareUpdateEntry	1.3.6.1.4.1.33.16.9.1.1		not-accessible	An entry in the table concerning the writing of firmware to a target I/O card.
INT firmwareUpdateSlotIndex	1.3.6.1.4.1.33.16.9.1.1.1	INTEGER	read-only	This variable identifies the slot to which is to be the target of the firmware update.
STR firmwareUpdateDefaultFileName	1.3.6.1.4.1.33.16.9.1.1.2	DisplayString	read-only	This variable when read will obtain the default file name from the target.
STR firmwareUpdateFileName	1.3.6.1.4.1.33.16.9.1.1.3	DisplayString	read-write	This variable contains the name of the file to be read from the flash memory card and written to the target.
INT firmwareUpdateStatus	1.3.6.1.4.1.33.16.9.1.1.4	INTEGER	read-write	This variable is used to start the update process. The agent always 'ready' for this value. Setting this value to 'execute' causes the agent to write the file specified by firmwareUpdateFileName to be written to the taget. Setting this value to 'execute' when firmwareUpdateFileName has not been written or when firmwareUpdateState is 'writing' causes bad value to be returned.
INT firmwareUpdateState	1.3.6.1.4.1.33.16.9.1.1.5	INTEGER	read-only	This variable indicates the current state of firmware update, 'idle' indicates that firmware update may be initiated, and 'writing' indicates that an update is in process.
INT firmwareUpdateCompletionStatus	1.3.6.1.4.1.33.16.9.1.1.6	INTEGER	read-only	This variable indicates the completion status of the the last firmware update attempt. 'none' indicates that no firmware update has yet been attempted.
INT firmwareUpdateMethod	1.3.6.1.4.1.33.16.9.1.1.7	INTEGER	read-write	This variable indicates the method of update of the firmware update attempt.
xApple	1.3.6.1.4.1.33.21
xAppleSystem	1.3.6.1.4.1.33.21.1
INT appleState	1.3.6.1.4.1.33.21.1.1	INTEGER	read-write	Controls whether the router will perform AppleTalk routing.
INT appleStatus	1.3.6.1.4.1.33.21.1.2	INTEGER	read-only	Indicates whether the router is performing AppleTalk routing.
INT appleStatusIf	1.3.6.1.4.1.33.21.1.3	INTEGER	read-only	The ifIndex of the bad interface if appleStatus is 'badConfig'.
xApplePort	1.3.6.1.4.1.33.21.2
applePortTable	1.3.6.1.4.1.33.21.2.1		not-accessible	Table of fields indexed by interface.
applePortEntry	1.3.6.1.4.1.33.21.2.1.1		not-accessible	A particular entry.
INT applePortIndex	1.3.6.1.4.1.33.21.2.1.1.1	INTEGER	read-only	The index of the interface; same as IfIndex.
INT applePortProtocolPriority	1.3.6.1.4.1.33.21.2.1.1.2	INTEGER	read-write	This value defines the priority at which all Apple routed packets will be placed on the WAN output queue.
INT applePortArpInterval	1.3.6.1.4.1.33.21.2.1.1.3	INTEGER	read-write	The interval at which ARP messages should be sent during the process of selecting a network address.
INT applePortArpRetransmitCount	1.3.6.1.4.1.33.21.2.1.1.4	INTEGER	read-write	The number of ARP messages that should be sent during the process of selecting a network address.
INT applePortChecksum	1.3.6.1.4.1.33.21.2.1.1.5	INTEGER	read-write	Controls whether checksums are generated on all DDP packets sent out the interface.
CTR applePortPacketsIn	1.3.6.1.4.1.33.21.2.1.1.6	Counter	read-only	The number of AppleTalk packets received on this interface.
CTR applePortPacketsOut	1.3.6.1.4.1.33.21.2.1.1.7	Counter	read-only	The number of AppleTalk packets transmitted on this interface.
CTR applePortForwardsIn	1.3.6.1.4.1.33.21.2.1.1.8	Counter	read-only	The number of AppleTalk packets received on this interface which were not addressed to this router.
CTR applePortForwardsOut	1.3.6.1.4.1.33.21.2.1.1.9	Counter	read-only	The number of AppleTalk packets transmitted on this interface which were not originated by this router.
ADR applePortNetAddress	1.3.6.1.4.1.33.21.2.1.1.10	DdpAddress	read-only	The actual address used by this port.
OCT applePortNetStart	1.3.6.1.4.1.33.21.2.1.1.11	OCTET STRING	read-only	The start of the actual network range used by this port.
OCT applePortNetEnd	1.3.6.1.4.1.33.21.2.1.1.12	OCTET STRING	read-only	The end of the actual network range used by this port.
CTR applePortErrors	1.3.6.1.4.1.33.21.2.1.1.13	Counter	read-only	The number of AppleTalk packets received in error.
INT applePortLastError	1.3.6.1.4.1.33.21.2.1.1.14	INTEGER	read-only	The type of the most recent error counted in applePortErrors. A value of zero means no error.
TIK applePortLastErrorTime	1.3.6.1.4.1.33.21.2.1.1.15	TimeTicks	read-only	The value of sysUptime when applePortLastError last occured.
OCT applePortLastErrorData	1.3.6.1.4.1.33.21.2.1.1.16	OCTET STRING	read-only	The first 22 bytes of the packet from applePortLastError.
INT applePortBringBackTime	1.3.6.1.4.1.33.21.2.1.1.17	INTEGER	read-write	The number of seconds to shut down an interface while waiting for a manager-initiated configuration change to propagate.
INT applePortUseNeighborNotify	1.3.6.1.4.1.33.21.2.1.1.18	INTEGER	read-write	Controls generation of neighbor notify messages when an interface is disabled or system is shut down.
INT applePortRouterType	1.3.6.1.4.1.33.21.2.1.1.19	INTEGER	read-write	Type of router operation over this port.
applePortZoneTable	1.3.6.1.4.1.33.21.2.2		not-accessible	Table of fields indexed by interface and zone.
applePortZoneEntry	1.3.6.1.4.1.33.21.2.2.1		not-accessible	A particular entry.
INT applePortZoneIndex	1.3.6.1.4.1.33.21.2.2.1.1	INTEGER	read-only	The index of the interface; same as IfIndex.
OCT applePortZoneName	1.3.6.1.4.1.33.21.2.2.1.2	OCTET STRING	read-only	The name of the zone.
INT applePortZoneStatus	1.3.6.1.4.1.33.21.2.2.1.3	INTEGER	read-write	The status of the entry. Set to 'invalid' to remove the entry.
xApplePolicy	1.3.6.1.4.1.33.21.3
applePortExportTable	1.3.6.1.4.1.33.21.3.1		not-accessible	Table of fields indexed by interface and zone.
applePortExportEntry	1.3.6.1.4.1.33.21.3.1.1		not-accessible	A particular entry.
INT applePortExportIndex	1.3.6.1.4.1.33.21.3.1.1.1	INTEGER	read-only	The index of the interface; same as IfIndex.
OCT applePortExportZone	1.3.6.1.4.1.33.21.3.1.1.2	OCTET STRING	read-only	The name of the zone.
OCT applePortExportName	1.3.6.1.4.1.33.21.3.1.1.3	OCTET STRING	read-only	The name of the name.
OCT applePortExportType	1.3.6.1.4.1.33.21.3.1.1.4	OCTET STRING	read-only	The name of the type.
INT applePortExportAction	1.3.6.1.4.1.33.21.3.1.1.5	INTEGER	read-write	Control whether the data will be hidden or advertised.
INT applePortExportStatus	1.3.6.1.4.1.33.21.3.1.1.6	INTEGER	read-write	The status of the entry. Set to 'invalid' to remove the entry.
applePortImportTable	1.3.6.1.4.1.33.21.3.2		not-accessible	Table of fields indexed by interface and zone.
applePortImportEntry	1.3.6.1.4.1.33.21.3.2.1		not-accessible	A particular entry.
INT applePortImportIndex	1.3.6.1.4.1.33.21.3.2.1.1	INTEGER	read-only	The index of the interface; same as IfIndex.
OCT applePortImportZone	1.3.6.1.4.1.33.21.3.2.1.2	OCTET STRING	read-only	The name of the zone.
OCT applePortImportName	1.3.6.1.4.1.33.21.3.2.1.3	OCTET STRING	read-only	The name of the name.
OCT applePortImportType	1.3.6.1.4.1.33.21.3.2.1.4	OCTET STRING	read-only	The name of the type.
INT applePortImportAction	1.3.6.1.4.1.33.21.3.2.1.5	INTEGER	read-write	Control whether the data will be discarded or accepted.
INT applePortImportStatus	1.3.6.1.4.1.33.21.3.2.1.6	INTEGER	read-write	The status of the entry. Set to 'invalid' to remove the entry.
xAppleNbp	1.3.6.1.4.1.33.21.4
appleNbpTable	1.3.6.1.4.1.33.21.4.1		not-accessible	Table of fields indexed by interface and zone.
appleNbpEntry	1.3.6.1.4.1.33.21.4.1.1		not-accessible	A particular entry.
OCT appleNbpZone	1.3.6.1.4.1.33.21.4.1.1.1	OCTET STRING	read-only	The name of the zone.
OCT appleNbpName	1.3.6.1.4.1.33.21.4.1.1.2	OCTET STRING	read-only	The name of the name.
OCT appleNbpType	1.3.6.1.4.1.33.21.4.1.1.3	OCTET STRING	read-only	The name of the type.
ADR appleNbpNode	1.3.6.1.4.1.33.21.4.1.1.4	DdpAddress	read-only	The address of the node who offers the service associated with this entry.
INT appleNbpSocket	1.3.6.1.4.1.33.21.4.1.1.5	INTEGER	read-only	The socket of the service associated with this entry. The value 0 means no socket.
xAppleTraffic	1.3.6.1.4.1.33.21.5
INT appleTrafficSort	1.3.6.1.4.1.33.21.5.1	INTEGER	read-write	Setting to EXECUTE causes the most recent traffic information to be sorted into the appleTrafficTable. The sorting precedence is: decreasing percentage, increasing destination address, increasing source address, and increasing interface number. Setting to READY has no effect.
appleTrafficTable	1.3.6.1.4.1.33.21.5.2		not-accessible	A list of traffic entries, sorted in the order specified by appleTrafficSort.
appleTrafficEntry	1.3.6.1.4.1.33.21.5.2.1		not-accessible	Parameter values for an Filter filter.
INT appleTrafficIndex	1.3.6.1.4.1.33.21.5.2.1.1	INTEGER	read-only	Identification of a traffic entry.
INT appleTrafficPercent	1.3.6.1.4.1.33.21.5.2.1.2	INTEGER	read-only	The percent of total traffic that this traffic entryrepresents, in tenths of a percent.
ADR appleTrafficDst	1.3.6.1.4.1.33.21.5.2.1.3	DdpAddress	read-only	The destination to which the traffic entry applies.
ADR appleTrafficSrc	1.3.6.1.4.1.33.21.5.2.1.4	DdpAddress	read-only	The source to which the traffic entry applies.
INT appleTrafficIntf	1.3.6.1.4.1.33.21.5.2.1.5	INTEGER	read-only	The inbound interface to which the traffic entry applies.
INT appleTrafficMonitoring	1.3.6.1.4.1.33.21.5.3	INTEGER	read-write	Controls whether internet traffic information will be recorded.
xAppleRemoteAccess	1.3.6.1.4.1.33.21.6
STR arapPassword	1.3.6.1.4.1.33.21.6.1	DisplayString	read-write	The server's ARAP password. To increase security, Gets of this object return the NULL string.
STR arapDefaultZoneName	1.3.6.1.4.1.33.21.6.2	DisplayString	read-write	The name of the AppleTalk zone that the server should try to choose at boot time.
arapPortTable	1.3.6.1.4.1.33.21.6.3		not-accessible	A list of ARAP port entries.
arapPortEntry	1.3.6.1.4.1.33.21.6.3.1		not-accessible	ARAP parameter values for a port.
INT arapPortEnabled	1.3.6.1.4.1.33.21.6.3.1.1	INTEGER	read-write	Indicates if ARAP connections are allowed on this port.
INT arapPortZoneAccess	1.3.6.1.4.1.33.21.6.3.1.2	INTEGER	read-write	Indicates the AppleTalk zones that ARAP connections on this port may access: none, local, all, or named zone.
STR arapPortZoneName	1.3.6.1.4.1.33.21.6.3.1.3	DisplayString	read-write	If this port's arapPortZoneAccess field indicates a named zone, this field contains the zone name.
INT arapPortMaxConnectTime	1.3.6.1.4.1.33.21.6.3.1.4	INTEGER	read-write	Maximum number of minutes a single ARAP connection may exist on the port before a server initiated disconnect. To set no limit on the amount of time that an ARAP user may be connected, set this object to -1.
INT arapPortGuestLoginsOk	1.3.6.1.4.1.33.21.6.3.1.5	INTEGER	read-write	Indicates if 'Guest' logins (with no password) are allowed on the port.
INT arapPortTimeConnected	1.3.6.1.4.1.33.21.6.3.1.6	INTEGER	read-only	Indicates the number of minutes the current ARAP connection has been established on the port, rounded up to the nearest minute. Gets return -1 if no ARAP user is currently connected on the port or if ARAP is not enabled on the port.
INT arapPortTimeRemaining	1.3.6.1.4.1.33.21.6.3.1.7	INTEGER	read-write	Indicates the number of minutes the current ARAP connection may remain on the port before a server initiated disconnect will occur, rounded up to the nearest minute. To set no limit on the amount of time that the current ARAP user may continue to be connected, set this object to the maximum value in the range. Gets return -1 if no ARAP user is currently connected on the port or if ARAP is not enabled on the port. Gets also return -1 if there is a user connected and there is no limit on the amount of time that the current user may be connected.
xPpp	1.3.6.1.4.1.33.22
xPppBasic	1.3.6.1.4.1.33.22.1
xPppConfigTable	1.3.6.1.4.1.33.22.1.1		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppConfigEntry	1.3.6.1.4.1.33.22.1.1.1		not-accessible	Management information about a particular PPP.
INT xPppConfigOpen	1.3.6.1.4.1.33.22.1.1.1.1	INTEGER	read-write	Determines if PPP is configured on this port.
INT xPppConfigActive	1.3.6.1.4.1.33.22.1.1.1.2	INTEGER	read-write	Determines if LCP will actively open or wait passively.
INT xPppConfigDefaults	1.3.6.1.4.1.33.22.1.1.1.3	INTEGER	read-write	Revert to factory default PPP parameters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' sets PPP parameters to factory defaults.
INT xPppConfigRestartTimer	1.3.6.1.4.1.33.22.1.1.1.4	INTEGER	read-write	The number of seconds waited before retransmitting during option negotiation.
INT xPppConfigConfLimit	1.3.6.1.4.1.33.22.1.1.1.5	INTEGER	read-write	Maximum number of times a configuration request will be sent to the peer without receiving a response.
INT xPppConfigFailLimit	1.3.6.1.4.1.33.22.1.1.1.6	INTEGER	read-write	Maximum number of times a peer's proposed option will be NAKed before REJECTing the option.
INT xPppConfigPacketLogging	1.3.6.1.4.1.33.22.1.1.1.7	INTEGER	read-write	Determines the level of packet logging to accounting on this port.
INT xPppConfigKATimer	1.3.6.1.4.1.33.22.1.1.1.8	INTEGER	read-write	Determines the number of seconds between transmission of LCP Echo Keepalive packets.
INT xPppConfigKATimeout	1.3.6.1.4.1.33.22.1.1.1.9	INTEGER	read-write	Determines the number of seconds to wait to hear LCP Echo Replies to our Echo Request Keepalive packets before giving up and shutting down the link.
xPppStatusTable	1.3.6.1.4.1.33.22.1.2		not-accessible	A table containing basic PPP status info.
xPppStatusEntry	1.3.6.1.4.1.33.22.1.2.1		not-accessible	Status information about a particular PPP.
INT xPppStatusState	1.3.6.1.4.1.33.22.1.2.1.1	INTEGER	read-only	Displays whether PPP is enabled or disabled on this port.
INT xPppLinkOpen	1.3.6.1.4.1.33.22.1.2.1.2	INTEGER	read-only	Displays open status of the link.
CTR xPppHdlcRxTotalPkts	1.3.6.1.4.1.33.22.1.2.1.3	Counter	read-only	Total of all packets received on PPP link.
CTR xPppHdlcTxTotalPkts	1.3.6.1.4.1.33.22.1.2.1.4	Counter	read-only	Total of all packets transmitted on PPP link.
CTR xPppHdlcRxFrameErrs	1.3.6.1.4.1.33.22.1.2.1.5	Counter	read-only	Number of framing errors received on PPP link.
CTR xPppHdlcRxNoBuffer	1.3.6.1.4.1.33.22.1.2.1.6	Counter	read-only	Number of times a buffer was not available to receive packet into.
CTR xPppHdlcTxNoBuffer	1.3.6.1.4.1.33.22.1.2.1.7	Counter	read-only	Number of times a buffer was not available to transmit a packet from.
CTR xPppHdlcRxBadFcs	1.3.6.1.4.1.33.22.1.2.1.8	Counter	read-only	Number of packets received with a bad checksum.
CTR xPppHdlcVJDiscards	1.3.6.1.4.1.33.22.1.2.1.9	Counter	read-only	Number of packets received that failed VJ decompression.
xPppLcp	1.3.6.1.4.1.33.22.2
xPppLcpConfigTable	1.3.6.1.4.1.33.22.2.1		not-accessible	A table containing PPP LCP specific variables for this PPP implementation.
xPppLcpConfigEntry	1.3.6.1.4.1.33.22.2.1.1		not-accessible	Management information about a particular PPP LCP session.
INT xPppLcpConfigAuth	1.3.6.1.4.1.33.22.2.1.1.1	INTEGER	read-write	Authentication protocol used for authenticating peers.
INT xPppLcpConfigChapAuth	1.3.6.1.4.1.33.22.2.1.1.2	INTEGER	read-write	Authentication CHAP protocol used for authenticating peers.
xPppLcpStatusTable	1.3.6.1.4.1.33.22.2.2		not-accessible	A table containing PPP LCP status info.
xPppLcpStatusEntry	1.3.6.1.4.1.33.22.2.2.1		not-accessible	Status information about a particular PPP LCP session.
INT xPppLcpStatusState	1.3.6.1.4.1.33.22.2.2.1.1	INTEGER	read-only	The current state of LCP.
INT xPppLcpStatusRxAuth	1.3.6.1.4.1.33.22.2.2.1.2	INTEGER	read-only	The authentication protocol currently in use from the peer to us.
INT xPppLcpStatusTxAuth	1.3.6.1.4.1.33.22.2.2.1.3	INTEGER	read-only	The authentication protocol currently in use from us to the peer.
CTR xPppLcpStatusRxConReq	1.3.6.1.4.1.33.22.2.2.1.4	Counter	read-only	The count of LCP Configure Requests received from the peer.
CTR xPppLcpStatusTxConReq	1.3.6.1.4.1.33.22.2.2.1.5	Counter	read-only	The count of LCP Configure Requests transmitted to the peer.
CTR xPppLcpStatusRxConNak	1.3.6.1.4.1.33.22.2.2.1.6	Counter	read-only	The count of LCP Configure Naks received from the peer.
CTR xPppLcpStatusTxConNak	1.3.6.1.4.1.33.22.2.2.1.7	Counter	read-only	The count of LCP Configure Naks transmitted to the peer.
CTR xPppLcpStatusRxConAck	1.3.6.1.4.1.33.22.2.2.1.8	Counter	read-only	The count of LCP Configure Acks received from the peer.
CTR xPppLcpStatusTxConAck	1.3.6.1.4.1.33.22.2.2.1.9	Counter	read-only	The count of LCP Configure Acks transmitted to the peer.
CTR xPppLcpStatusRxConRej	1.3.6.1.4.1.33.22.2.2.1.10	Counter	read-only	The count of LCP Configure Rejects received from the peer.
CTR xPppLcpStatusTxConRej	1.3.6.1.4.1.33.22.2.2.1.11	Counter	read-only	The count of LCP Configure Rejects transmitted to the peer.
CTR xPppLcpStatusRxTrmReq	1.3.6.1.4.1.33.22.2.2.1.12	Counter	read-only	The count of LCP Terminate Requests received from the peer.
CTR xPppLcpStatusTxTrmReq	1.3.6.1.4.1.33.22.2.2.1.13	Counter	read-only	The count of LCP Terminate Requests transmitted to the peer.
CTR xPppLcpStatusRxTrmAck	1.3.6.1.4.1.33.22.2.2.1.14	Counter	read-only	The count of LCP Terminate Acks received from the peer.
CTR xPppLcpStatusTxTrmAck	1.3.6.1.4.1.33.22.2.2.1.15	Counter	read-only	The count of LCP Terminate Acks transmitted to the peer.
CTR xPppLcpStatusRxEcoReq	1.3.6.1.4.1.33.22.2.2.1.16	Counter	read-only	The count of LCP Echo Requests received from the peer.
CTR xPppLcpStatusTxEcoReq	1.3.6.1.4.1.33.22.2.2.1.17	Counter	read-only	The count of LCP Echo Requests transmitted to the peer.
CTR xPppLcpStatusRxEcoRep	1.3.6.1.4.1.33.22.2.2.1.18	Counter	read-only	The count of LCP Echo Reply received from the peer.
CTR xPppLcpStatusTxEcoRep	1.3.6.1.4.1.33.22.2.2.1.19	Counter	read-only	The count of LCP Echo Reply transmitted to the peer.
CTR xPppLcpStatusRxCodRej	1.3.6.1.4.1.33.22.2.2.1.20	Counter	read-only	The count of LCP Code Rejects received from the peer.
CTR xPppLcpStatusTxCodRej	1.3.6.1.4.1.33.22.2.2.1.21	Counter	read-only	The count of LCP Code Rejects transmitted to the peer.
CTR xPppLcpStatusRxProRej	1.3.6.1.4.1.33.22.2.2.1.22	Counter	read-only	The count of LCP Protocol Rejects received from the peer.
CTR xPppLcpStatusTxProRej	1.3.6.1.4.1.33.22.2.2.1.23	Counter	read-only	The count of LCP Protocol Rejects transmitted to the peer.
INT xPppLcpStatusState2	1.3.6.1.4.1.33.22.2.2.1.24	INTEGER	read-only	The current state of LCP.
xPppIpcp	1.3.6.1.4.1.33.22.3
xPppIpcpConfigTable	1.3.6.1.4.1.33.22.3.1		not-accessible	A table containing PPP IPCPspecific variables for this PPP implementation.
xPppIpcpConfigEntry	1.3.6.1.4.1.33.22.3.1.1		not-accessible	Management information about a particular PPP IPCP session.
IP xPppIpcpConfigLocalAddress	1.3.6.1.4.1.33.22.3.1.1.1	IpAddress	read-write	IP Address of the local PPP interface.
IP xPppIpcpConfigRemoteAddress	1.3.6.1.4.1.33.22.3.1.1.2	IpAddress	read-write	IP Address of the peer PPP interface.
INT xPppIpcpConfigVJCompSlots	1.3.6.1.4.1.33.22.3.1.1.3	INTEGER	read-write	Number of slots to be used by VJ compression.
IP xPppIpcpConfigRangeStart	1.3.6.1.4.1.33.22.3.1.1.4	IpAddress	read-write	Start of acceptable address range in which the negotiated remote IP address must fall.
IP xPppIpcpConfigRangeEnd	1.3.6.1.4.1.33.22.3.1.1.5	IpAddress	read-write	End of acceptable address range in which the negotiated remote IP address must fall.
INT xPppIpcpConfigState	1.3.6.1.4.1.33.22.3.1.1.6	INTEGER	read-write	Controls whether IPCP is allowed to run on this port.
IP xPppIpcpConfigLocalRangeStart	1.3.6.1.4.1.33.22.3.1.1.7	IpAddress	read-write	Start of acceptable address range in which the negotiated local IP address must fall.
IP xPppIpcpConfigLocalRangeEnd	1.3.6.1.4.1.33.22.3.1.1.8	IpAddress	read-write	End of acceptable address range in which the negotiated local IP address must fall.
IP xPppIpcpConfigPppIpMask	1.3.6.1.4.1.33.22.3.1.1.9	IpAddress	read-write	The subnet mask to use for a PPP operation on the port. Corresponds directly to the value labeled 'IP Mask:' in the PPP PORT IP CHARACTERISTICS display.
xPppIpcpAsyncConfigTable	1.3.6.1.4.1.33.22.3.2		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppIpcpAsyncConfigEntry	1.3.6.1.4.1.33.22.3.2.1		not-accessible	Management information about a particular PPP Asynchronous LCP.
INT xPppIpcpAsyncConfigBrdcast	1.3.6.1.4.1.33.22.3.2.1.1	INTEGER	read-write	Determines whether to forward an IP Broadcast or not.
xPppIpcpStatusTable	1.3.6.1.4.1.33.22.3.3		not-accessible	A table containing basic PPP IPCP status info.
xPppIpcpStatusEntry	1.3.6.1.4.1.33.22.3.3.1		not-accessible	Status information about a particular PPP IPCP session.
INT xPppIpcpStatusState	1.3.6.1.4.1.33.22.3.3.1.1	INTEGER	read-only	The current state of IPCP.
IP xPppIpcpStatusLocalAddress	1.3.6.1.4.1.33.22.3.3.1.2	IpAddress	read-only	The IP Address currently being used by the local IPCP.
IP xPppIpcpStatusRemoteAddress	1.3.6.1.4.1.33.22.3.3.1.3	IpAddress	read-only	The IP Address currently being used by the Remote IPCP.
CTR xPppIpcpRxPkts	1.3.6.1.4.1.33.22.3.3.1.4	Counter	read-only	Total number of IP packets received.
CTR xPppIpcpTxPkts	1.3.6.1.4.1.33.22.3.3.1.5	Counter	read-only	Total number of IP packets transmitted.
CTR xPppIpcpRxConReq	1.3.6.1.4.1.33.22.3.3.1.6	Counter	read-only	The count of IPCP Configure Requests received from the peer.
CTR xPppIpcpTxConReq	1.3.6.1.4.1.33.22.3.3.1.7	Counter	read-only	The count of IPCP Configure Requests transmitted to the peer.
CTR xPppIpcpRxConNak	1.3.6.1.4.1.33.22.3.3.1.8	Counter	read-only	The count of IPCP Configure Naks received from the peer.
CTR xPppIpcpTxConNak	1.3.6.1.4.1.33.22.3.3.1.9	Counter	read-only	The count of IPCP Configure Naks transmitted to the peer.
CTR xPppIpcpRxConAck	1.3.6.1.4.1.33.22.3.3.1.10	Counter	read-only	The count of IPCP Configure Acks received from the peer.
CTR xPppIpcpTxConAck	1.3.6.1.4.1.33.22.3.3.1.11	Counter	read-only	The count of IPCP Configure Acks transmitted to the peer.
CTR xPppIpcpRxConRej	1.3.6.1.4.1.33.22.3.3.1.12	Counter	read-only	The count of IPCP Configure Rejects received from the peer.
CTR xPppIpcpTxConRej	1.3.6.1.4.1.33.22.3.3.1.13	Counter	read-only	The count of IPCP Configure Rejects transmitted to the peer.
CTR xPppIpcpRxTrmReq	1.3.6.1.4.1.33.22.3.3.1.14	Counter	read-only	The count of IPCP Terminate Requests received from the peer.
CTR xPppIpcpTxTrmReq	1.3.6.1.4.1.33.22.3.3.1.15	Counter	read-only	The count of IPCP Terminate Requests transmitted to the peer.
CTR xPppIpcpRxTrmAck	1.3.6.1.4.1.33.22.3.3.1.16	Counter	read-only	The count of IPCP Terminate Acks received from the peer.
CTR xPppIpcpTxTrmAck	1.3.6.1.4.1.33.22.3.3.1.17	Counter	read-only	The count of IPCP Terminate Acks transmitted to the peer.
INT xPppIpcpStatusState2	1.3.6.1.4.1.33.22.3.3.1.18	INTEGER	read-only	The current state of IPCP.
xPppAuth	1.3.6.1.4.1.33.22.4
OCT xPppPapPassword	1.3.6.1.4.1.33.22.4.1	OCTET STRING	read-write	The password to use for PAP authentication.
xPppAuthConfigTable	1.3.6.1.4.1.33.22.4.2		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppAuthConfigEntry	1.3.6.1.4.1.33.22.4.2.1		not-accessible	Management information about a particular PPP.
INT xPppAuthChapChallengeTimer	1.3.6.1.4.1.33.22.4.2.1.4	INTEGER	read-write	Length of time in minutes between CHAP reauthentication challenges. A value of zero disables the timer.
INT xPppAuthPapConfigState	1.3.6.1.4.1.33.22.4.2.1.5	INTEGER	read-write	Controls the type of Pap authentication required for this port, and whether it is combined with another authentication mechanism such as Radius.
INT xPppAuthChapConfigState	1.3.6.1.4.1.33.22.4.2.1.6	INTEGER	read-write	Controls the type of Chap authentication required for this port, and whether it is combined with another authentication mechanism such as Radius.
xPppAuthStatusTable	1.3.6.1.4.1.33.22.4.3		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppAuthStatusEntry	1.3.6.1.4.1.33.22.4.3.1		not-accessible	Management information about a particular PPP.
INT xPppPapStatusState	1.3.6.1.4.1.33.22.4.3.1.4	INTEGER	read-only	The current state of PAP.
INT xPppChapStatusState	1.3.6.1.4.1.33.22.4.3.1.5	INTEGER	read-only	The current state of CHAP.
OCT xPppChapPassword	1.3.6.1.4.1.33.22.4.4	OCTET STRING	read-write	The password to use for CHAP authentication.
xPppIpxcp	1.3.6.1.4.1.33.22.5
xPppIpxcpConfigTable	1.3.6.1.4.1.33.22.5.1		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppIpxcpConfigEntry	1.3.6.1.4.1.33.22.5.1.1		not-accessible	Management information about a particular PPP.
INT xPppIpxcpCipxCompression	1.3.6.1.4.1.33.22.5.1.1.1	INTEGER	read-write	Controls whether CIPX compression will be negotiated on the interface.
OCT xPppIpxcpConfigRemoteNode	1.3.6.1.4.1.33.22.5.1.1.2	OCTET STRING	read-write	The IPX Node address which can be offered to the peer if it does not know a Node number but requires one.
xPppIpxcpStatusTable	1.3.6.1.4.1.33.22.5.2		not-accessible	A table containing PPP specific variables for this PPP implementation.
xPppIpxcpStatusEntry	1.3.6.1.4.1.33.22.5.2.1		not-accessible	Management information about a particular PPP.
INT xPppIpxcpStatusState	1.3.6.1.4.1.33.22.5.2.1.1	INTEGER	read-only	The current state of IPXCP.
INT xPppIpxcpCipxInCompression	1.3.6.1.4.1.33.22.5.2.1.2	INTEGER	read-only	The current state of CIPX compression inbound.
INT xPppIpxcpCipxOutCompression	1.3.6.1.4.1.33.22.5.2.1.3	INTEGER	read-only	The current state of CIPX compression outbound.
INT xPppIpxcpCipxInSlots	1.3.6.1.4.1.33.22.5.2.1.4	INTEGER	read-only	The current number of CIPX compression inbound slots.
INT xPppIpxcpCipxOutSlots	1.3.6.1.4.1.33.22.5.2.1.5	INTEGER	read-only	The current number of CIPX compression outbound slots.
OCT xPppIpxcpStatusRemoteNode	1.3.6.1.4.1.33.22.5.2.1.6	OCTET STRING	read-only	The IPX Node address currently being used by the Remote IPX peer.
xPppIpxcpCountersTable	1.3.6.1.4.1.33.22.5.3		not-accessible	A table containing basic PPP IPXCP status info.
xPppIpxcpCountersEntry	1.3.6.1.4.1.33.22.5.3.1		not-accessible	Counter information about a particular PPP IPXCP session.
CTR xPppIpxcpRxConReq	1.3.6.1.4.1.33.22.5.3.1.1	Counter	read-only	The count of IPXCP Configure Requests received from the peer.
CTR xPppIpxcpTxConReq	1.3.6.1.4.1.33.22.5.3.1.2	Counter	read-only	The count of IPXCP Configure Requests transmitted to the peer.
CTR xPppIpxcpRxConNak	1.3.6.1.4.1.33.22.5.3.1.3	Counter	read-only	The count of IPXCP Configure Naks received from the peer.
CTR xPppIpxcpTxConNak	1.3.6.1.4.1.33.22.5.3.1.4	Counter	read-only	The count of IPXCP Configure Naks transmitted to the peer.
CTR xPppIpxcpRxConAck	1.3.6.1.4.1.33.22.5.3.1.5	Counter	read-only	The count of IPXCP Configure Acks received from the peer.
CTR xPppIpxcpTxConAck	1.3.6.1.4.1.33.22.5.3.1.6	Counter	read-only	The count of IPXCP Configure Acks transmitted to the peer.
CTR xPppIpxcpRxConRej	1.3.6.1.4.1.33.22.5.3.1.7	Counter	read-only	The count of IPXCP Configure Rejects received from the peer.
CTR xPppIpxcpTxConRej	1.3.6.1.4.1.33.22.5.3.1.8	Counter	read-only	The count of IPXCP Configure Rejects transmitted to the peer.
CTR xPppIpxcpRxTrmReq	1.3.6.1.4.1.33.22.5.3.1.9	Counter	read-only	The count of IPXCP Terminate Requests received from the peer.
CTR xPppIpxcpTxTrmReq	1.3.6.1.4.1.33.22.5.3.1.10	Counter	read-only	The count of IPXCP Terminate Requests transmitted to the peer.
CTR xPppIpxcpRxTrmAck	1.3.6.1.4.1.33.22.5.3.1.11	Counter	read-only	The count of IPXCP Terminate Acks received from the peer.
CTR xPppIpxcpTxTrmAck	1.3.6.1.4.1.33.22.5.3.1.12	Counter	read-only	The count of IPXCP Terminate Acks transmitted to the peer.
xRadius	1.3.6.1.4.1.33.35
xRadiusPort	1.3.6.1.4.1.33.35.1
xRadiusPortTable	1.3.6.1.4.1.33.35.1.1		not-accessible	Table of fields indexed by port.
xRadiusPortEntry	1.3.6.1.4.1.33.35.1.1.1		not-accessible	A particular entry.
INT xRadiusPortIndex	1.3.6.1.4.1.33.35.1.1.1.1	INTEGER	read-only	The index of the port.
INT xRadiusPortStatus	1.3.6.1.4.1.33.35.1.1.1.2	INTEGER	read-only	Indicates the state of Radius Authentication on the port.
INT xRadiusPortSolicitStatus	1.3.6.1.4.1.33.35.1.1.1.3	INTEGER	read-write	Indicates the state of Radius solicitation mode on the port.
INT xRadiusAcctPortStatus	1.3.6.1.4.1.33.35.1.1.1.4	INTEGER	read-only	Indicates the state of Radius Accounting on the port.
xRadiusCircuit	1.3.6.1.4.1.33.35.2
xRadiusConfig	1.3.6.1.4.1.33.35.3
INT xRadiusAuthServerPort	1.3.6.1.4.1.33.35.3.1	INTEGER	read-write	The UDP port on which the Radius authentication request will be made.
INT xRadiusAcctServerPort	1.3.6.1.4.1.33.35.3.2	INTEGER	read-write	The UDP port on which the Radius accounting request will be made.
INT xRadiusTimeout	1.3.6.1.4.1.33.35.3.3	INTEGER	read-write	The period of time that the Radius client will wait for a reply from the server.

CTR ipxIfFramesIn

1.3.6.1.4.1.33.15.2.1.1.5

Counter

read-only

The number of IPX frames received on this interface.

CTR ipxIfFramesOut

1.3.6.1.4.1.33.15.2.1.1.6

Counter

read-only

The number of IPX frames sent on this interface.

CTR ipxIfErrors

1.3.6.1.4.1.33.15.2.1.1.7

Counter

read-only

The number of IPX errors seen on this interface.

INT ipxIfTransitDelay

1.3.6.1.4.1.33.15.2.1.1.8

INTEGER

read-write

The number of 55 millisecond ticks it takes for a packet to travel from one destination to another on the interface. A value of 0 means that the system will calculate this value based on the measured speed of the interface.

INT ipxIfTransitDelayActual

1.3.6.1.4.1.33.15.2.1.1.9

INTEGER

read-only

The number of 55 millisecond ticks it takes for a packet to travel from one destination to another on the interface.

INT ipxIfProtocolPriority

1.3.6.1.4.1.33.15.2.1.1.10

INTEGER

read-write

This value defines the priority at which all Internet Routed packets will be placed on the WAN output queue.

INT ipxIfWatchdogSpoof

1.3.6.1.4.1.33.15.2.1.1.11

INTEGER

read-write

Control for whether or not this router responds to IPX watchog requests on this interface.

INT ipxIfStatusNetwork

1.3.6.1.4.1.33.15.2.1.1.12

INTEGER

read-only

The IPX network number that is actually in use on the attached interface. This value may have been learned via listening to the attached network.

xIpxNetbios

1.3.6.1.4.1.33.15.3

INT ipxNetbiosHopLimit

1.3.6.1.4.1.33.15.3.1

INTEGER

read-write

Maximum number of hops that an IPX Netbios packet may make.

ipxNetbiosIfTable

1.3.6.1.4.1.33.15.3.2

not-accessible

A list of IPX interface entries.

ipxNetbiosIfEntry

1.3.6.1.4.1.33.15.3.2.1

not-accessible

IPX interface parameters and counters.

INT ipxNetbiosIfIndex

1.3.6.1.4.1.33.15.3.2.1.1

INTEGER

read-only

An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT ipxIfNetbiosForwarding

1.3.6.1.4.1.33.15.3.2.1.2

INTEGER

read-write

Control whether Netbios packet will be forwarded in or out on this interface.

CTR ipxIfNetbiosIn

1.3.6.1.4.1.33.15.3.2.1.3

Counter

read-only

The number of IPX Netbios frames received on this interface.

CTR ipxIfNetbiosOut

1.3.6.1.4.1.33.15.3.2.1.4

Counter

read-only

The number of IPX Netbios frames sent on this interface.

xIpxRip

1.3.6.1.4.1.33.15.4

ipxRipIfTable

1.3.6.1.4.1.33.15.4.1

not-accessible

A list of IPX interface entries.

ipxRipIfEntry

1.3.6.1.4.1.33.15.4.1.1

not-accessible

IPX interface parameters and counters.

INT ipxRipIfIndex

1.3.6.1.4.1.33.15.4.1.1.1

INTEGER

read-only

An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT ipxIfRipBcst

1.3.6.1.4.1.33.15.4.1.1.2

INTEGER

read-write

Control whether RIP packets will be broadcasted out this interface.

INT ipxIfRipBcstDiscardTimeout

1.3.6.1.4.1.33.15.4.1.1.3

INTEGER

read-write

The number of seconds to wait before discarding information learned from a RIP broadcast.

INT ipxIfRipBcstTimer

1.3.6.1.4.1.33.15.4.1.1.4

INTEGER

read-write

The number of seconds to wait between sending out RIP broadcasts.

CTR ipxIfRipIn

1.3.6.1.4.1.33.15.4.1.1.5

Counter

read-only

The number of RIP broadcasts received on this interface.

CTR ipxIfRipOut

1.3.6.1.4.1.33.15.4.1.1.6

Counter

read-only

The number of RIP broadcasts sent on this interface.

CTR ipxIfRipAgedOut

1.3.6.1.4.1.33.15.4.1.1.7

Counter

read-only

The number of entries timed out and discarded on this interface.

ipxRipTable

1.3.6.1.4.1.33.15.4.2

not-accessible

A list of RIP entries.

ipxRipEntry

1.3.6.1.4.1.33.15.4.2.1

not-accessible

IPX interface parameters and counters.

INT ipxRipNetwork

1.3.6.1.4.1.33.15.4.2.1.1

INTEGER

read-only

An IPX network number to which this router knows a path.

OCT ipxRipRouter

1.3.6.1.4.1.33.15.4.2.1.2

OCTET STRING

read-only

The Ethernet address of an IPX router on this network.

INT ipxRipInterface

1.3.6.1.4.1.33.15.4.2.1.3

INTEGER

read-only

The interface to reach the router. A value of ifIndex.

INT ipxRipHops

1.3.6.1.4.1.33.15.4.2.1.4

INTEGER

read-only

The number of hops to reach the router.

INT ipxRipTransTime

1.3.6.1.4.1.33.15.4.2.1.5

INTEGER

read-only

The number of 55 millisecond ticks it takes for a packet to travel to the router.

INT ipxRipAge

1.3.6.1.4.1.33.15.4.2.1.6

INTEGER

read-only

The age of the RIP entry in seconds.

ipxRipRtTable

1.3.6.1.4.1.33.15.4.3

not-accessible

A list of RIP Routing entries.

ipxRipRtEntry

1.3.6.1.4.1.33.15.4.3.1

not-accessible

IPX Routing Entry information

INT ipxRipRtNetwork

1.3.6.1.4.1.33.15.4.3.1.1

INTEGER

read-only

An IPX network number to which this router knows a path.

OCT ipxRipRtRouter

1.3.6.1.4.1.33.15.4.3.1.2

OCTET STRING

read-only

The Ethernet address of an IPX router on this network.

INT ipxRipRtInterface

1.3.6.1.4.1.33.15.4.3.1.3

INTEGER

read-only

The interface to reach the router. A value of ifIndex.

INT ipxRipRtHops

1.3.6.1.4.1.33.15.4.3.1.4

INTEGER

read-write

The number of hops to reach the router.

INT ipxRipRtTransTime

1.3.6.1.4.1.33.15.4.3.1.5

INTEGER

read-write

The number of 55 millisecond ticks it takes for a packet to travel to the router.

INT ipxRipRtOrigin

1.3.6.1.4.1.33.15.4.3.1.6

INTEGER

read-only

The source of the RIP entry, either Learned via RIP or Static.

INT ipxRipRtRowStatus

1.3.6.1.4.1.33.15.4.3.1.7

INTEGER

read-write

Create or Delete RIP routing table entries.

xIpxSap

1.3.6.1.4.1.33.15.5

ipxSapIfTable

1.3.6.1.4.1.33.15.5.1

not-accessible

A list of IPX interface entries.

ipxSapIfEntry

1.3.6.1.4.1.33.15.5.1.1

not-accessible

IPX interface parameters and counters.

INT ipxSapIfIndex

1.3.6.1.4.1.33.15.5.1.1.1

INTEGER

read-only

An index value that uniquely identifies an IPX interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT ipxIfSapBcst

1.3.6.1.4.1.33.15.5.1.1.2

INTEGER

read-write

Control whether SAP packets will be broadcasted out this interface.

INT ipxIfSapBcstDiscardTimeout

1.3.6.1.4.1.33.15.5.1.1.3

INTEGER

read-write

The number of seconds to wait before discarding information learned from a SAP broadcast.

INT ipxIfSapBcstTimer

1.3.6.1.4.1.33.15.5.1.1.4

INTEGER

read-write

The number of seconds to wait between sending out SAP broadcasts.

CTR ipxIfSapIn

1.3.6.1.4.1.33.15.5.1.1.5

Counter

read-only

The number SAP broadcasts received on this interface.

CTR ipxIfSapOut

1.3.6.1.4.1.33.15.5.1.1.6

Counter

read-only

The number SAP broadcasts sent on this interface.

CTR ipxIfSapAgedOut

1.3.6.1.4.1.33.15.5.1.1.7

Counter

read-only

The number entries for this interface discarded due to aging timeout.

ipxSapTable

1.3.6.1.4.1.33.15.5.2

not-accessible

A list of SAP entries.

ipxSapEntry

1.3.6.1.4.1.33.15.5.2.1

not-accessible

IPX interface parameters and counters.

STR ipxSapName

1.3.6.1.4.1.33.15.5.2.1.1

DisplayString

read-only

The name of the service, null filled.

INT ipxSapNetwork

1.3.6.1.4.1.33.15.5.2.1.2

INTEGER

read-only

The IPX network number on which the service's host resides.

OCT ipxSapHost

1.3.6.1.4.1.33.15.5.2.1.3

OCTET STRING

read-only

The Ethernet address of the IPX host of the service.

INT ipxSapSocket

1.3.6.1.4.1.33.15.5.2.1.4

INTEGER

read-only

The socket number of the service on the host.

INT ipxSapInterface

1.3.6.1.4.1.33.15.5.2.1.5

INTEGER

read-only

The interface of the router in the direction of the service. A value of ifIndex.

INT ipxSapType

1.3.6.1.4.1.33.15.5.2.1.6

INTEGER

read-only

The type of the service. The enumeration is an incomplete set of all possible values.

INT ipxSapAge

1.3.6.1.4.1.33.15.5.2.1.7

INTEGER

read-only

The age of the Sap entry in seconds.

ipxSapSvTable

1.3.6.1.4.1.33.15.5.3

not-accessible

A list of SAP entries.

ipxSapSvEntry

1.3.6.1.4.1.33.15.5.3.1

not-accessible

IPX interface parameters and counters.

STR ipxSapSvName

1.3.6.1.4.1.33.15.5.3.1.1

DisplayString

read-only

The name of the service.

INT ipxSapSvNetwork

1.3.6.1.4.1.33.15.5.3.1.2

INTEGER

read-only

The IPX network number on which the service's host resides.

OCT ipxSapSvHost

1.3.6.1.4.1.33.15.5.3.1.3

OCTET STRING

read-only

The Ethernet address of the IPX host of the service.

INT ipxSapSvSocket

1.3.6.1.4.1.33.15.5.3.1.4

INTEGER

read-only

The socket number of the service on the host.

INT ipxSapSvInterface

1.3.6.1.4.1.33.15.5.3.1.5

INTEGER

read-only

The interface of the router in the direction of the service. A value of ifIndex.

INT ipxSapSvOrigin

1.3.6.1.4.1.33.15.5.3.1.6

INTEGER

read-only

The source of the RIP entry, either Learned via RIP or Static.

INT ipxSapSvType

1.3.6.1.4.1.33.15.5.3.1.7

INTEGER

read-only

The type of the service. The enumeration is an incomplete set of all possible values.

INT ipxSapSvHops

1.3.6.1.4.1.33.15.5.3.1.8

INTEGER

read-write

The number of hops to the Service.

INT ipxSapSvRowStatus

1.3.6.1.4.1.33.15.5.3.1.9

INTEGER

read-write

Create or Delete SAP Service table entries.

INT ipxSapSvAge

1.3.6.1.4.1.33.15.5.3.1.10

INTEGER

read-only

The age of the Sap entry in seconds.

xIpxFilter

1.3.6.1.4.1.33.15.6

ipxIfFilterTable

1.3.6.1.4.1.33.15.6.1

not-accessible

A list of IPX interface Source and Destination address Filter entries.

ipxIfFilterEntry

1.3.6.1.4.1.33.15.6.1.1

not-accessible

IPX Source and Destination interface Filters.

INT ipxIfFilterIndex

1.3.6.1.4.1.33.15.6.1.1.1

INTEGER

read-only

The interface to which this IPX Address filter applies. A value of ifIndex.

INT ipxIfFilterDestNetwork

1.3.6.1.4.1.33.15.6.1.1.2

INTEGER

read-only

The destination IPX network to be filtered.

OCT ipxIfFilterDestNode

1.3.6.1.4.1.33.15.6.1.1.3

OCTET STRING

read-only

The destination IPX node to be filtered.

INT ipxIfFilterSourceNetwork

1.3.6.1.4.1.33.15.6.1.1.4

INTEGER

read-only

The destination IPX network to be filtered.

OCT ipxIfFilterSourceNode

1.3.6.1.4.1.33.15.6.1.1.5

OCTET STRING

read-only

The destination IPX node to be filtered.

INT ipxIfFilterPacketType

1.3.6.1.4.1.33.15.6.1.1.6

INTEGER

read-only

The IPX packet type to be filtered.

INT ipxIfFilterAction

1.3.6.1.4.1.33.15.6.1.1.7

INTEGER

read-write

The IPX filter action to be taken, either Forward or Discard.

INT ipxIfFilterRowStatus

1.3.6.1.4.1.33.15.6.1.1.8

INTEGER

read-write

The IPX Filter create or delete function.

INT ipxIfFilterStatusDestNetworkAll

1.3.6.1.4.1.33.15.6.1.1.9

INTEGER

read-only

The IPX Filter flag meaning ALL destination networks.

INT ipxIfFilterStatusDestNodeAll

1.3.6.1.4.1.33.15.6.1.1.10

INTEGER

read-only

The IPX Filter flag meaning ALL destination nodes.

INT ipxIfFilterStatusSourceNetworkAll

1.3.6.1.4.1.33.15.6.1.1.11

INTEGER

read-only

The IPX Filter flag meaning ALL source networks.

INT ipxIfFilterStatusSourceNodeAll

1.3.6.1.4.1.33.15.6.1.1.12

INTEGER

read-only

The IPX Filter flag meaning ALL source nodes.

INT ipxIfFilterStatusPacketTypeAll

1.3.6.1.4.1.33.15.6.1.1.13

INTEGER

read-only

The IPX Filter flag meaning ALL packet types.

ipxIfRipFilterTable

1.3.6.1.4.1.33.15.6.2

not-accessible

A list of IPX interface RIP Filter entries.

ipxIfRipFilterEntry

1.3.6.1.4.1.33.15.6.2.1

not-accessible

IPX RIP interface Filters.

INT ipxIfRipFilterNetwork

1.3.6.1.4.1.33.15.6.2.1.1

INTEGER

read-only

The IPX RIP network to be filtered.

INT ipxIfRipFilterType

1.3.6.1.4.1.33.15.6.2.1.2

INTEGER

read-only

The IPX RIP filter type, either IMPORT or EXPORT.

INT ipxIfRipFilterAction

1.3.6.1.4.1.33.15.6.2.1.3

INTEGER

read-write

The IPX RIP filter action to be taken, either ALLOW or DENY.

INT ipxIfRipFilterRowStatus

1.3.6.1.4.1.33.15.6.2.1.4

INTEGER

read-write

The IPX RIP Filter create or delete function.

INT ipxIfRipFilterNetworkAll

1.3.6.1.4.1.33.15.6.2.1.5

INTEGER

read-only

The IPX RIP Filter flag meaning filter ALL networks.

OCT ipxIfRipFilterHost

1.3.6.1.4.1.33.15.6.2.1.6

OCTET STRING

read-only

The RIP Filter IPX Host Address from which RIP will ALLOW/DENY IMPORT of routes.

ipxIfSapFilterTable

1.3.6.1.4.1.33.15.6.3

not-accessible

A list of IPX interface SAP Filter entries.

ipxIfSapFilterEntry

1.3.6.1.4.1.33.15.6.3.1

not-accessible

IPX SAP interface Filters.

INT ipxIfSapFilterNetwork

1.3.6.1.4.1.33.15.6.3.1.1

INTEGER

read-only

The IPX SAP network to be filtered.

INT ipxIfSapFilterType

1.3.6.1.4.1.33.15.6.3.1.2

INTEGER

read-only

The IPX SAP filter type, either IMPORT or EXPORT.

INT ipxIfSapFilterServiceType

1.3.6.1.4.1.33.15.6.3.1.3

INTEGER

read-only

The IPX SAP service type to which this filter applies.

INT ipxIfSapFilterAction

1.3.6.1.4.1.33.15.6.3.1.4

INTEGER

read-write

The IPX SAP filter action to be taken, either ALLOW or DENY.

INT ipxIfSapFilterRowStatus

1.3.6.1.4.1.33.15.6.3.1.5

INTEGER

read-write

The IPX SAP Filter create or delete function.

INT ipxIfSapFilterNetworkAll

1.3.6.1.4.1.33.15.6.3.1.6

INTEGER

read-only

The IPX SAP Filter flag meaning filter ALL networks.

INT ipxIfSapFilterServiceTypeAll

1.3.6.1.4.1.33.15.6.3.1.7

INTEGER

read-only

The IPX SAP Filter flag meaning filter ALL service types.

STR ipxIfSapFilterName

1.3.6.1.4.1.33.15.6.3.1.8

DisplayString

read-only

The name of the service to be filtered.

OCT ipxIfSapFilterHost

1.3.6.1.4.1.33.15.6.3.1.9

OCTET STRING

read-only

The IPX Host address from which SAP will ALLOW/DENY IMPORT of services .

xIpxPrinter

1.3.6.1.4.1.33.15.8

ipxPrinterPortTable

1.3.6.1.4.1.33.15.8.1

not-accessible

A list of IPX printer character port entries.

ipxPrinterPortEntry

1.3.6.1.4.1.33.15.8.1.1

not-accessible

IPX printer parameter values for a character port.

INT ipxPrinterPortIndex

1.3.6.1.4.1.33.15.8.1.1.1

INTEGER

read-only

An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.

INT ipxPrinterPortStatus

1.3.6.1.4.1.33.15.8.1.1.2

INTEGER

read-write

Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.

STR ipxPrinterPortServer

1.3.6.1.4.1.33.15.8.1.1.3

DisplayString

read-write

The name of an active print server on the network.

INT ipxPrinterPortPrinter

1.3.6.1.4.1.33.15.8.1.1.4

INTEGER

read-write

An available remote printer on ixpPrinterPortServer.

INT ipxTimeout

1.3.6.1.4.1.33.15.8.1.1.5

INTEGER

read-write

A control to set the the time at which a print job from a print server will be timed out and the port freed.

INT ipxPrinterEthernet

1.3.6.1.4.1.33.15.8.2

INTEGER

read-write

Control for use of Ethernet-style message framing, with the IPX protocol type. Mutually exclusive with ipxPrinterMac, ipxPrinterMac802_2_Snap, and ipxPrinterMac802_2.

INT ipxPrinterMac

1.3.6.1.4.1.33.15.8.3

INTEGER

read-write

Control for use of MAC-only message framing, with no protocol type. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac802_2_Snap, and ipxPrinterMac802_2.

INT ipxPrinterMac802_2

1.3.6.1.4.1.33.15.8.4

INTEGER

read-write

Control for use of MAC message framing with 802.2 framing. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac, and ipxPrinterMac802_2_Snap.

INT ipxPrinterMac802_2_Snap

1.3.6.1.4.1.33.15.8.5

INTEGER

read-write

Control for use of MAC-only message framing with 802 Snap framing. Mutually exclusive with ipxPrinterEthernet, ipxPrinterMac, and ipxPrinterMac802_2.

xChassis

1.3.6.1.4.1.33.16

xChassisBasic

1.3.6.1.4.1.33.16.1

MAC basicBase802Address

1.3.6.1.4.1.33.16.1.1

MacAddress

read-only

Base IEEE 802 global address for the chassis.

INT basicSlot

1.3.6.1.4.1.33.16.1.2

INTEGER

read-only

Chassis slot number (slotIndex) of the system whose agent is supplying this MIB.

INT basicSlotNumber

1.3.6.1.4.1.33.16.1.3

INTEGER

read-only

Number of slots in the chassis.

MAC basicNewBase802Address

1.3.6.1.4.1.33.16.1.4

MacAddress

read-write

New base IEEE 802 global address for the chassis. Must be set in conjunction with featType 'changeEthernetAddress' and featKey from the MRV In-Reach System MIB.

xSegment

1.3.6.1.4.1.33.16.2

segmentTable

1.3.6.1.4.1.33.16.2.1

not-accessible

A list of segment entries, one for each segment of each type on the chassis.

segmentEntry

1.3.6.1.4.1.33.16.2.1.1

not-accessible

Values for a chassis segment.

NET segmentType

1.3.6.1.4.1.33.16.2.1.1.1

NetworkType

read-only

The segment type.

LET segmentIndex

1.3.6.1.4.1.33.16.2.1.1.2

Letter

read-only

An index value that uniquely identifies a segment.

xPort

1.3.6.1.4.1.33.16.3

IOT portIOCardType

1.3.6.1.4.1.33.16.3.1

IOType

read-only

The hardware type of the I/O card in this slot.

SER portIOCardSerialNumber

1.3.6.1.4.1.33.16.3.2

SerialNumber

read-only

The MRV In-Reach serial number of the I/O card in this slot.

INT portIOCardOperStatus

1.3.6.1.4.1.33.16.3.3

INTEGER

read-only

Status of the I/O card relative to the function card in this slot.

portTable

1.3.6.1.4.1.33.16.3.4

not-accessible

A list of port entries, one for each port of each type on the slots I/O card.

portEntry

1.3.6.1.4.1.33.16.3.4.1

not-accessible

Values for an I/O card port.

NET portType

1.3.6.1.4.1.33.16.3.4.1.1

NetworkType

read-only

The port type.

INT portIndex

1.3.6.1.4.1.33.16.3.4.1.2

INTEGER

read-only

An index value that uniquely identifies a port.

xController

1.3.6.1.4.1.33.16.4

controllerTable

1.3.6.1.4.1.33.16.4.1

not-accessible

A list of controller entries, one for each controller of each type on the local system.

controllerEntry

1.3.6.1.4.1.33.16.4.1.1

not-accessible

Values for a controller.

NET controllerType

1.3.6.1.4.1.33.16.4.1.1.1

NetworkType

read-only

The controller type.

INT controllerIndex

1.3.6.1.4.1.33.16.4.1.1.2

INTEGER

read-only

An index value that uniquely identifies a controller.

OID controllerNetwork

1.3.6.1.4.1.33.16.4.1.1.3

OBJECT IDENTIFIER

read-write

The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this controller is to use, that is, segmentType, portType or controllerType.

xInterface

1.3.6.1.4.1.33.16.5

interfaceTable

1.3.6.1.4.1.33.16.5.1

not-accessible

A list of interface entries, corresponding to the MIB II Interface group. These are directly equivalent to hardware network controllers, and must be the lowest numbered interfaces on the system.

interfaceEntry

1.3.6.1.4.1.33.16.5.1.1

not-accessible

Values for an interface.

INT interfaceIndex

1.3.6.1.4.1.33.16.5.1.1.1

INTEGER

read-only

An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

OID interfaceNetwork

1.3.6.1.4.1.33.16.5.1.1.2

OBJECT IDENTIFIER

read-write

The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this interface is to use, that is, segmentType, portType, or controllerType.

xSlotBootControl

1.3.6.1.4.1.33.16.6

slotBootControlTable

1.3.6.1.4.1.33.16.6.1

not-accessible

A list of slot boot control entries.

slotBootControlEntry

1.3.6.1.4.1.33.16.6.1.1

not-accessible

Values for a chassis slot.

INT slotBootControlSlot

1.3.6.1.4.1.33.16.6.1.1.1

INTEGER

read-only

An index value that uniquely identifies a slot, defined the same as slotIndex.

INT slotBootControlIndex

1.3.6.1.4.1.33.16.6.1.1.2

INTEGER

read-only

An index value that uniquely identifies a boot control entry, from 1 to the number of entries for the slot.

INT slotBootControlStatus

1.3.6.1.4.1.33.16.6.1.1.3

INTEGER

read-write

The status of the entry. Set to 'disabled' to disable the entry.

OID slotBootControlController

1.3.6.1.4.1.33.16.6.1.1.4

OBJECT IDENTIFIER

read-write

The instance identifier of the first object in the conceptual row entry for the controller this entry selects for bootstrap operation, that is, controllerType. This entry must be compatible with slotBootControlNetwork, including being of the same network type. The value 0.0 indicates default action.

OID slotBootControlNetwork

1.3.6.1.4.1.33.16.6.1.1.5

OBJECT IDENTIFIER

read-write

The instance identifier of the first object in the conceptual row entry for the segment or port this entry selects for bootstrap operation, that is, segmentType or portType. This entry must be compatible with slotBootControlController, including being of the same network type. The value 0.0 indicates default action.

STR slotBootControlMopFile

1.3.6.1.4.1.33.16.6.1.1.6

DisplayString

read-write

The software file name to request for down-line load of the server via MOP or XMOP.

STR slotBootControlInternetFile

1.3.6.1.4.1.33.16.6.1.1.7

DisplayString

read-write

The filename to request when loading an image via TFTP.

IP slotBootControlInternetAddress

1.3.6.1.4.1.33.16.6.1.1.8

IpAddress

read-write

The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action.

IP slotBootControlInternetServer

1.3.6.1.4.1.33.16.6.1.1.9

IpAddress

read-write

The internet address of the server to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.

IP slotBootControlInternetGateway

1.3.6.1.4.1.33.16.6.1.1.10

IpAddress

read-write

The internet address of the gateway to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.

STR slotBootControlInternetDelimiter

1.3.6.1.4.1.33.16.6.1.1.11

DisplayString

read-write

The character separating the load file directory name from the file name.

slotBootControlFlagTable

1.3.6.1.4.1.33.16.6.2

not-accessible

A list of slot boot control source flag entries.

slotBootControlFlagEntry

1.3.6.1.4.1.33.16.6.2.1

not-accessible

Values for a boot control flag.

INT slotBootControlFlagLoadBootpTftp

1.3.6.1.4.1.33.16.6.2.1.1

INTEGER

read-write

Control for performing load over BOOTP/TFTP.

INT slotBootControlFlagParamBootpTftp

1.3.6.1.4.1.33.16.6.2.1.2

INTEGER

read-write

Control for performing parameter load over BOOTP/TFTP.

INT slotBootControlFlagDumpBootpTftp

1.3.6.1.4.1.33.16.6.2.1.3

INTEGER

read-write

Control for performing dump over BOOTP/TFTP.

INT slotBootControlFlagLoadTftpDirect

1.3.6.1.4.1.33.16.6.2.1.4

INTEGER

read-write

Control for performing load over direct TFTP.

INT slotBootControlFlagParamTftpDirect

1.3.6.1.4.1.33.16.6.2.1.5

INTEGER

read-write

Control for performing parameter load over direct TFTP.

INT slotBootControlFlagDumpTftpDirect

1.3.6.1.4.1.33.16.6.2.1.6

INTEGER

read-write

Control for performing dump over direct TFTP.

INT slotBootControlFlagLoadLocal

1.3.6.1.4.1.33.16.6.2.1.7

INTEGER

read-write

Control for performing load from a local device.

INT slotBootControlFlagParamLocal

1.3.6.1.4.1.33.16.6.2.1.8

INTEGER

read-write

Control for performing parameter load from a local device.

INT slotBootControlFlagDumpLocal

1.3.6.1.4.1.33.16.6.2.1.9

INTEGER

read-write

Control for performing dump from a local device.

INT slotBootControlFlagLoadMop

1.3.6.1.4.1.33.16.6.2.1.10

INTEGER

read-write

Control for performing load over Digital's MOP.

INT slotBootControlFlagParamMop

1.3.6.1.4.1.33.16.6.2.1.11

INTEGER

read-write

Control for performing parameter load over Digital's MOP.

INT slotBootControlFlagDumpMop

1.3.6.1.4.1.33.16.6.2.1.12

INTEGER

read-write

Control for performing dump over Digital's MOP.

INT slotBootControlFlagLoadXmop

1.3.6.1.4.1.33.16.6.2.1.13

INTEGER

read-write

Control for performing load over MRV In-Reach extended MOP.

INT slotBootControlFlagParamXmop

1.3.6.1.4.1.33.16.6.2.1.14

INTEGER

read-write

Control for performing parameter load over MRV In-Reach extended MOP.

INT slotBootControlFlagDumpXmop

1.3.6.1.4.1.33.16.6.2.1.15

INTEGER

read-write

Control for performing dump over MRV In-Reach extended MOP.

INT slotBootControlFlagLoadRarpTftp

1.3.6.1.4.1.33.16.6.2.1.16

INTEGER

read-write

Control for performing load over RARP/TFTP.

INT slotBootControlFlagParamRarpTftp

1.3.6.1.4.1.33.16.6.2.1.17

INTEGER

read-write

Control for performing parameter load over RARP/TFTP.

INT slotBootControlFlagDumpRarpTftp

1.3.6.1.4.1.33.16.6.2.1.18

INTEGER

read-write

Control for performing dump over RARP/TFTP.

slotBootControlStorageTable

1.3.6.1.4.1.33.16.6.3

not-accessible

A list of slot boot control Storage entries.

slotBootControlStorageEntry

1.3.6.1.4.1.33.16.6.3.1

not-accessible

Values for a chassis slot.

INT slotBootControlStorageClientSlot

1.3.6.1.4.1.33.16.6.3.1.1

INTEGER

read-only

An index value that uniquely identifies a slot, defined the same as slotIndex.

INT slotBootControlStorageServerSlot

1.3.6.1.4.1.33.16.6.3.1.2

INTEGER

read-only

An index value that uniquely identifies the slot in which the Storage record resides, with the same values as slotIndex.

INT slotBootControlStorageStatus

1.3.6.1.4.1.33.16.6.3.1.3

INTEGER

read-only

The status of the entry.

CTR slotBootControlStorageFailures

1.3.6.1.4.1.33.16.6.3.1.4

Counter

read-only

The number of times a read from or write to a given Storage location failed

xSlot

1.3.6.1.4.1.33.16.7

slotTable

1.3.6.1.4.1.33.16.7.1

not-accessible

A list of slot entries.

slotEntry

1.3.6.1.4.1.33.16.7.1.1

not-accessible

Values for a chassis slot.

INT slotIndex

1.3.6.1.4.1.33.16.7.1.1.1

INTEGER

read-only

An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as basicSlot. As the objects found at instance zero are duplicates, that instance does not appear in responses a get-next, that is, the lowest numbered slotIndex returned by get-next is 1.

INT slotAdminAction

1.3.6.1.4.1.33.16.7.1.1.2

INTEGER

read-write

Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of slotOperStatus.

INT slotOperStatus

1.3.6.1.4.1.33.16.7.1.1.3

INTEGER

read-only

Relative to the chassis, the current operating status of the system in the slot.

GAU slotSecondsSinceReset

1.3.6.1.4.1.33.16.7.1.1.4

Gauge

read-only

The number of seconds since the system in the slot was last reset by hardware or software.

HAR slotHardwareType

1.3.6.1.4.1.33.16.7.1.1.5

HardwareType

read-only

The type of hardware in the slot.

SER slotHardwareSerialNumber

1.3.6.1.4.1.33.16.7.1.1.6

SerialNumber

read-only

The MRV In-Reach serial number of the function card hardware in this slot.

INT slotHardwareRevision

1.3.6.1.4.1.33.16.7.1.1.7

INTEGER

read-only

This revision level of the function card hardware in the slot.

IOT slotIOCardType

1.3.6.1.4.1.33.16.7.1.1.8

IOType

read-only

The hardware type of the I/O card in this slot.

SER slotIOCardSerialNumber

1.3.6.1.4.1.33.16.7.1.1.9

SerialNumber

read-only

The MRV In-Reach serial number of the I/O card in this slot.

INT slotIOCardOperStatus

1.3.6.1.4.1.33.16.7.1.1.10

INTEGER

read-only

Status of the I/O card relative to the function card in this slot.

INT slotBootstrapFirmwareRevision

1.3.6.1.4.1.33.16.7.1.1.11

INTEGER

read-only

The firmware revision level of the bootstrap ROM installed in the system in the slot.

INT slotElementalFirmwareRevision

1.3.6.1.4.1.33.16.7.1.1.12

INTEGER

read-only

The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot.

INT slotMemorySize

1.3.6.1.4.1.33.16.7.1.1.13

INTEGER

read-only

The number of bytes of memory installed in the system in the slot.

GAU slotLedNumber

1.3.6.1.4.1.33.16.7.1.1.14

Gauge

read-only

The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable.

OCT slotLedStatus

1.3.6.1.4.1.33.16.7.1.1.15

OCTET STRING

read-only

The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the first byte of the value, proceeding to the low-order bit, then to then next byte. On the system hardware, the first LED is at the top, left, front, proceeding left to right, top to bottom, and front to back.

MAC slotBase802Address

1.3.6.1.4.1.33.16.7.1.1.16

MacAddress

read-only

Base IEEE 802 global address for the slot.

IP slotIpAddress

1.3.6.1.4.1.33.16.7.1.1.17

IpAddress

read-only

An internet address to which the system in this slot might respond. May be one of many.

INT slotPlus5Status

1.3.6.1.4.1.33.16.7.1.1.18

INTEGER

read-only

Status of the +5 volt power to the slot.

INT slotPlus12Status

1.3.6.1.4.1.33.16.7.1.1.19

INTEGER

read-only

Status of the +12 volt power to the slot.

INT slotMinus12Status

1.3.6.1.4.1.33.16.7.1.1.20

INTEGER

read-only

Status of the -12 volt power to the slot.

GAU slotPlus5Watts

1.3.6.1.4.1.33.16.7.1.1.21

Gauge

read-only

Tenths of watts of +5 volt power currently drawn by the slot.

GAU slotPlus12Watts

1.3.6.1.4.1.33.16.7.1.1.22

Gauge

read-only

Tenths of watts of +12 volt power currently drawn by the slot.

GAU slotMinus12Watts

1.3.6.1.4.1.33.16.7.1.1.23

Gauge

read-only

Tenths of watts of -12 volt power currently drawn by the slot.

INT slotIOCardHardwareVersion

1.3.6.1.4.1.33.16.7.1.1.24

INTEGER

read-only

Version number of I/O card in the slot.

INT slotRestoreNVS

1.3.6.1.4.1.33.16.7.1.1.25

INTEGER

read-write

Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' has no effect.

INT slotDefaultNVS

1.3.6.1.4.1.33.16.7.1.1.26

INTEGER

read-write

Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect.

slotBootTable

1.3.6.1.4.1.33.16.7.2

not-accessible

A list of slot bootstrap status entries. A given slot has an entry in this table only when slotOperStatus is one of: loadRequested, loading, dumpRequested, dumping, paramRequested, paramLoading

slotBootEntry

1.3.6.1.4.1.33.16.7.2.1

not-accessible

Bootstrap status values for a chassis slot.

INT slotBootIndex

1.3.6.1.4.1.33.16.7.2.1.1

INTEGER

read-only

An index value that uniquely identifies a slot, defined the same as slotIndex.

INT slotBootIfIndex

1.3.6.1.4.1.33.16.7.2.1.2

INTEGER

read-only

An index value that uniquely identifies the interface in use for bootstrap functions. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

OID slotBootNetwork

1.3.6.1.4.1.33.16.7.2.1.3

OBJECT IDENTIFIER

read-only

The instance identifier of the first object in the conceptual row entry for the segment or port this interface is using, that is, segmentType or portType.

INT slotBootProtocol

1.3.6.1.4.1.33.16.7.2.1.4

INTEGER

read-only

The protocol in use for bootstrap operation.

MAC slotBoot802Address

1.3.6.1.4.1.33.16.7.2.1.5

MacAddress

read-only

IEEE 802 global address in use for bootstrap operation.

ADR slotBootAddressType

1.3.6.1.4.1.33.16.7.2.1.6

AddressType

read-only

The type of network address contained in slotBootAddress.

OCT slotBootAddress

1.3.6.1.4.1.33.16.7.2.1.7

OCTET STRING

read-only

The network address the system in the slot is using to identify itself for bootstrap operation.

ADR slotBootServerAddressType

1.3.6.1.4.1.33.16.7.2.1.8

AddressType

read-only

The type of network address contained in slotBootServerAddress.

OCT slotBootServerAddress

1.3.6.1.4.1.33.16.7.2.1.9

OCTET STRING

read-only

The network address of the system supplying bootstrap services to the system in the slot.

IP slotBootGatewayAddress

1.3.6.1.4.1.33.16.7.2.1.10

IpAddress

read-only

The internet address of the router in use for bootstrap operation.

STR slotBootFileName

1.3.6.1.4.1.33.16.7.2.1.11

DisplayString

read-only

The full name of the file in use for bootstrap operation.

GAU slotBootBlockNumber

1.3.6.1.4.1.33.16.7.2.1.12

Gauge

read-only

The current block number being transferred for bootstrap operation, zero if unknown or not applicable.

OCT slotBootCrashCode

1.3.6.1.4.1.33.16.7.2.1.13

OCTET STRING

read-only

If slotOperStatus is dumpRequested or dumping, a code number to identify the crash reason; otherwise zero length.

slotControllerTable

1.3.6.1.4.1.33.16.7.3

not-accessible

A list of controller entries, one for each controller of each type in each slot.

slotControllerEntry

1.3.6.1.4.1.33.16.7.3.1

not-accessible

Values for a controller.

NET slotControllerType

1.3.6.1.4.1.33.16.7.3.1.1

NetworkType

read-only

The controller type.

INT slotControllerIndex

1.3.6.1.4.1.33.16.7.3.1.2

INTEGER

read-only

An index value that uniquely identifies a controller.

OID slotControllerNetwork

1.3.6.1.4.1.33.16.7.3.1.3

OBJECT IDENTIFIER

read-only

The instance identifier of the first object in the conceptual row entry for the segment or port this controller is to use, that is, segmentType or portType.

xPowerSupply

1.3.6.1.4.1.33.16.8

powerSupplyTable

1.3.6.1.4.1.33.16.8.1

not-accessible

A list of power supply entries.

powerSupplyEntry

1.3.6.1.4.1.33.16.8.1.1

not-accessible

Values for a chassis power supply.

INT powerSupplyIndex

1.3.6.1.4.1.33.16.8.1.1.1

INTEGER

read-only

An index value that uniquely identifies a power supply, in the range 1 to the number of power supply slots in the chassis.

INT powerSupplyAdminAction

1.3.6.1.4.1.33.16.8.1.1.2

INTEGER

read-write

Control to cause reset of the power supply. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of powerSupplyRedundancyStatus.

INT powerSupplyFirmwareVersion

1.3.6.1.4.1.33.16.8.1.1.3

INTEGER

read-only

Version number of power supply firmware.

INT powerSupplyRedundancyStatus

1.3.6.1.4.1.33.16.8.1.1.4

INTEGER

read-only

The current redundancy status of the power supply.

INT powerSupplyPlus5Status

1.3.6.1.4.1.33.16.8.1.1.5

INTEGER

read-only

Status of the +5 volt power from the power supply.

INT powerSupplyPlus12Status

1.3.6.1.4.1.33.16.8.1.1.6

INTEGER

read-only

Status of the +12 volt power from the power supply.

INT powerSupplyMinus12Status

1.3.6.1.4.1.33.16.8.1.1.7

INTEGER

read-only

Status of the -12 volt power from the power supply.

INT powerSupplyThermalWarningStatus

1.3.6.1.4.1.33.16.8.1.1.8

INTEGER

read-only

The current thermal warning status of the power supply.

INT powerSupplyThermalShutdownStatus

1.3.6.1.4.1.33.16.8.1.1.9

INTEGER

read-only

The current thermal shutdown status of the power supply.

INT powerSupplyFanStatus

1.3.6.1.4.1.33.16.8.1.1.10

INTEGER

read-only

The current status of the power supply's fan.

INT powerSupplyHardwareInhibitStatus

1.3.6.1.4.1.33.16.8.1.1.11

INTEGER

read-only

The current status of the power supply's hardware inhibit.

INT powerSupplyPlus5History

1.3.6.1.4.1.33.16.8.1.1.12

INTEGER

read-only

History of the +5 volt power from the power supply.

INT powerSupplyPlus12History

1.3.6.1.4.1.33.16.8.1.1.13

INTEGER

read-only

History of the +12 volt power from the power supply.

INT powerSupplyMinus12History

1.3.6.1.4.1.33.16.8.1.1.14

INTEGER

read-only

History of the -12 volt power from the power supply.

INT powerSupplyThermalWarningHistory

1.3.6.1.4.1.33.16.8.1.1.15

INTEGER

read-only

The thermal warning history of the power supply.

INT powerSupplyThermalShutdownHistory

1.3.6.1.4.1.33.16.8.1.1.16

INTEGER

read-only

The thermal shutdown history of the power supply.

INT powerSupplyFanHistory

1.3.6.1.4.1.33.16.8.1.1.17

INTEGER

read-only

The status history of the power supply's fan.

INT powerSupplyHardwareInhibitHistory

1.3.6.1.4.1.33.16.8.1.1.18

INTEGER

read-only

The status history of the power supply's hardware inhibit.

GAU powerSupplyPlus5Volts

1.3.6.1.4.1.33.16.8.1.1.19

Gauge

read-only

In hundredths, volts of +5 volt power currently provided by the power supply. A value of 0 indicates unknown.

GAU powerSupplyPlus12Volts

1.3.6.1.4.1.33.16.8.1.1.20

Gauge

read-only

In hundredths, volts of +12 volt power currently provided by the power supply. A value of 0 indicates unknown.

GAU powerSupplyMinus12Volts

1.3.6.1.4.1.33.16.8.1.1.21

Gauge

read-only

In hundredths, volts of -12 volt power currently provided by the power supply. A value of 0 indicates unknown.

GAU powerSupplyWatts

1.3.6.1.4.1.33.16.8.1.1.22

Gauge

read-only

Watts of power currently drawn from this power supply. A value of 0 indicates unknown.

GAU powerSupplyWattsMax

1.3.6.1.4.1.33.16.8.1.1.23

Gauge

read-only

Maximum watts of power available from this power supply. A value of 0 indicates unknown.

GAU powerSupplyChassisWatts

1.3.6.1.4.1.33.16.8.1.1.24

Gauge

read-only

Total watts of power currently drawn by the entire chassis. A value of 0 indicates unknown.

GAU powerSupplyChassisWattsMax

1.3.6.1.4.1.33.16.8.1.1.25

Gauge

read-only

Total maximum watts of power available from all the power supplies in the chassis. A value of 0 indicates unknown.

INT powerSupplyHardwareType

1.3.6.1.4.1.33.16.8.1.1.26

INTEGER

read-only

The type of power supply.

xFirmwareUpdate

1.3.6.1.4.1.33.16.9

firmwareUpdateTable

1.3.6.1.4.1.33.16.9.1

not-accessible

Table of descriptive and status information concerning the writing of firmware to a target I/O card.

firmwareUpdateEntry

1.3.6.1.4.1.33.16.9.1.1

not-accessible

An entry in the table concerning the writing of firmware to a target I/O card.

INT firmwareUpdateSlotIndex

1.3.6.1.4.1.33.16.9.1.1.1

INTEGER

read-only

This variable identifies the slot to which is to be the target of the firmware update.

STR firmwareUpdateDefaultFileName

1.3.6.1.4.1.33.16.9.1.1.2

DisplayString

read-only

This variable when read will obtain the default file name from the target.

STR firmwareUpdateFileName

1.3.6.1.4.1.33.16.9.1.1.3

DisplayString

read-write

This variable contains the name of the file to be read from the flash memory card and written to the target.

INT firmwareUpdateStatus

1.3.6.1.4.1.33.16.9.1.1.4

INTEGER

read-write

This variable is used to start the update process. The agent always 'ready' for this value. Setting this value to 'execute' causes the agent to write the file specified by firmwareUpdateFileName to be written to the taget. Setting this value to 'execute' when firmwareUpdateFileName has not been written or when firmwareUpdateState is 'writing' causes bad value to be returned.

INT firmwareUpdateState

1.3.6.1.4.1.33.16.9.1.1.5

INTEGER

read-only

This variable indicates the current state of firmware update, 'idle' indicates that firmware update may be initiated, and 'writing' indicates that an update is in process.

INT firmwareUpdateCompletionStatus

1.3.6.1.4.1.33.16.9.1.1.6

INTEGER

read-only

This variable indicates the completion status of the the last firmware update attempt. 'none' indicates that no firmware update has yet been attempted.

INT firmwareUpdateMethod

1.3.6.1.4.1.33.16.9.1.1.7

INTEGER

read-write

This variable indicates the method of update of the firmware update attempt.

xApple

1.3.6.1.4.1.33.21

xAppleSystem

1.3.6.1.4.1.33.21.1

INT appleState

1.3.6.1.4.1.33.21.1.1

INTEGER

read-write

Controls whether the router will perform AppleTalk routing.

INT appleStatus

1.3.6.1.4.1.33.21.1.2

INTEGER

read-only

Indicates whether the router is performing AppleTalk routing.

INT appleStatusIf

1.3.6.1.4.1.33.21.1.3

INTEGER

read-only

The ifIndex of the bad interface if appleStatus is 'badConfig'.

xApplePort

1.3.6.1.4.1.33.21.2

applePortTable

1.3.6.1.4.1.33.21.2.1

not-accessible

Table of fields indexed by interface.

applePortEntry

1.3.6.1.4.1.33.21.2.1.1

not-accessible

A particular entry.

INT applePortIndex

1.3.6.1.4.1.33.21.2.1.1.1

INTEGER

read-only

The index of the interface; same as IfIndex.

INT applePortProtocolPriority

1.3.6.1.4.1.33.21.2.1.1.2

INTEGER

read-write

This value defines the priority at which all Apple routed packets will be placed on the WAN output queue.

INT applePortArpInterval

1.3.6.1.4.1.33.21.2.1.1.3

INTEGER

read-write

The interval at which ARP messages should be sent during the process of selecting a network address.

INT applePortArpRetransmitCount

1.3.6.1.4.1.33.21.2.1.1.4

INTEGER

read-write

The number of ARP messages that should be sent during the process of selecting a network address.

INT applePortChecksum

1.3.6.1.4.1.33.21.2.1.1.5

INTEGER

read-write

Controls whether checksums are generated on all DDP packets sent out the interface.

CTR applePortPacketsIn

1.3.6.1.4.1.33.21.2.1.1.6

Counter

read-only

The number of AppleTalk packets received on this interface.

CTR applePortPacketsOut

1.3.6.1.4.1.33.21.2.1.1.7

Counter

read-only

The number of AppleTalk packets transmitted on this interface.

CTR applePortForwardsIn

1.3.6.1.4.1.33.21.2.1.1.8

Counter

read-only

The number of AppleTalk packets received on this interface which were not addressed to this router.

CTR applePortForwardsOut

1.3.6.1.4.1.33.21.2.1.1.9

Counter

read-only

The number of AppleTalk packets transmitted on this interface which were not originated by this router.

ADR applePortNetAddress

1.3.6.1.4.1.33.21.2.1.1.10

DdpAddress

read-only

The actual address used by this port.

OCT applePortNetStart

1.3.6.1.4.1.33.21.2.1.1.11

OCTET STRING

read-only

The start of the actual network range used by this port.

OCT applePortNetEnd

1.3.6.1.4.1.33.21.2.1.1.12

OCTET STRING

read-only

The end of the actual network range used by this port.

CTR applePortErrors

1.3.6.1.4.1.33.21.2.1.1.13

Counter

read-only

The number of AppleTalk packets received in error.

INT applePortLastError

1.3.6.1.4.1.33.21.2.1.1.14

INTEGER

read-only

The type of the most recent error counted in applePortErrors. A value of zero means no error.

TIK applePortLastErrorTime

1.3.6.1.4.1.33.21.2.1.1.15

TimeTicks

read-only

The value of sysUptime when applePortLastError last occured.

OCT applePortLastErrorData

1.3.6.1.4.1.33.21.2.1.1.16

OCTET STRING

read-only

The first 22 bytes of the packet from applePortLastError.

INT applePortBringBackTime

1.3.6.1.4.1.33.21.2.1.1.17

INTEGER

read-write

The number of seconds to shut down an interface while waiting for a manager-initiated configuration change to propagate.

INT applePortUseNeighborNotify

1.3.6.1.4.1.33.21.2.1.1.18

INTEGER

read-write

Controls generation of neighbor notify messages when an interface is disabled or system is shut down.

INT applePortRouterType

1.3.6.1.4.1.33.21.2.1.1.19

INTEGER

read-write

Type of router operation over this port.

applePortZoneTable

1.3.6.1.4.1.33.21.2.2

not-accessible

Table of fields indexed by interface and zone.

applePortZoneEntry

1.3.6.1.4.1.33.21.2.2.1

not-accessible

A particular entry.

INT applePortZoneIndex

1.3.6.1.4.1.33.21.2.2.1.1

INTEGER

read-only

The index of the interface; same as IfIndex.

OCT applePortZoneName

1.3.6.1.4.1.33.21.2.2.1.2

OCTET STRING

read-only

The name of the zone.

INT applePortZoneStatus

1.3.6.1.4.1.33.21.2.2.1.3

INTEGER

read-write

The status of the entry. Set to 'invalid' to remove the entry.

xApplePolicy

1.3.6.1.4.1.33.21.3

applePortExportTable

1.3.6.1.4.1.33.21.3.1

not-accessible

Table of fields indexed by interface and zone.

applePortExportEntry

1.3.6.1.4.1.33.21.3.1.1

not-accessible

A particular entry.

INT applePortExportIndex

1.3.6.1.4.1.33.21.3.1.1.1

INTEGER

read-only

The index of the interface; same as IfIndex.

OCT applePortExportZone

1.3.6.1.4.1.33.21.3.1.1.2

OCTET STRING

read-only

The name of the zone.

OCT applePortExportName

1.3.6.1.4.1.33.21.3.1.1.3

OCTET STRING

read-only

The name of the name.

OCT applePortExportType

1.3.6.1.4.1.33.21.3.1.1.4

OCTET STRING

read-only

The name of the type.

INT applePortExportAction

1.3.6.1.4.1.33.21.3.1.1.5

INTEGER

read-write

Control whether the data will be hidden or advertised.

INT applePortExportStatus

1.3.6.1.4.1.33.21.3.1.1.6

INTEGER

read-write

The status of the entry. Set to 'invalid' to remove the entry.

applePortImportTable

1.3.6.1.4.1.33.21.3.2

not-accessible

Table of fields indexed by interface and zone.

applePortImportEntry

1.3.6.1.4.1.33.21.3.2.1

not-accessible

A particular entry.

INT applePortImportIndex

1.3.6.1.4.1.33.21.3.2.1.1

INTEGER

read-only

The index of the interface; same as IfIndex.

OCT applePortImportZone

1.3.6.1.4.1.33.21.3.2.1.2

OCTET STRING

read-only

The name of the zone.

OCT applePortImportName

1.3.6.1.4.1.33.21.3.2.1.3

OCTET STRING

read-only

The name of the name.

OCT applePortImportType

1.3.6.1.4.1.33.21.3.2.1.4

OCTET STRING

read-only

The name of the type.

INT applePortImportAction

1.3.6.1.4.1.33.21.3.2.1.5

INTEGER

read-write

Control whether the data will be discarded or accepted.

INT applePortImportStatus

1.3.6.1.4.1.33.21.3.2.1.6

INTEGER

read-write

The status of the entry. Set to 'invalid' to remove the entry.

xAppleNbp

1.3.6.1.4.1.33.21.4

appleNbpTable

1.3.6.1.4.1.33.21.4.1

not-accessible

Table of fields indexed by interface and zone.

appleNbpEntry

1.3.6.1.4.1.33.21.4.1.1

not-accessible

A particular entry.

OCT appleNbpZone

1.3.6.1.4.1.33.21.4.1.1.1

OCTET STRING

read-only

The name of the zone.

OCT appleNbpName

1.3.6.1.4.1.33.21.4.1.1.2

OCTET STRING

read-only

The name of the name.

OCT appleNbpType

1.3.6.1.4.1.33.21.4.1.1.3

OCTET STRING

read-only

The name of the type.

ADR appleNbpNode

1.3.6.1.4.1.33.21.4.1.1.4

DdpAddress

read-only

The address of the node who offers the service associated with this entry.

INT appleNbpSocket

1.3.6.1.4.1.33.21.4.1.1.5

INTEGER

read-only

The socket of the service associated with this entry. The value 0 means no socket.

xAppleTraffic

1.3.6.1.4.1.33.21.5

INT appleTrafficSort

1.3.6.1.4.1.33.21.5.1

INTEGER

read-write

Setting to EXECUTE causes the most recent traffic information to be sorted into the appleTrafficTable. The sorting precedence is: decreasing percentage, increasing destination address, increasing source address, and increasing interface number. Setting to READY has no effect.

appleTrafficTable

1.3.6.1.4.1.33.21.5.2

not-accessible

A list of traffic entries, sorted in the order specified by appleTrafficSort.

appleTrafficEntry

1.3.6.1.4.1.33.21.5.2.1

not-accessible

Parameter values for an Filter filter.

INT appleTrafficIndex

1.3.6.1.4.1.33.21.5.2.1.1

INTEGER

read-only

Identification of a traffic entry.

INT appleTrafficPercent

1.3.6.1.4.1.33.21.5.2.1.2

INTEGER

read-only

The percent of total traffic that this traffic entryrepresents, in tenths of a percent.

ADR appleTrafficDst

1.3.6.1.4.1.33.21.5.2.1.3

DdpAddress

read-only

The destination to which the traffic entry applies.

ADR appleTrafficSrc

1.3.6.1.4.1.33.21.5.2.1.4

DdpAddress

read-only

The source to which the traffic entry applies.

INT appleTrafficIntf

1.3.6.1.4.1.33.21.5.2.1.5

INTEGER

read-only

The inbound interface to which the traffic entry applies.

INT appleTrafficMonitoring

1.3.6.1.4.1.33.21.5.3

INTEGER

read-write

Controls whether internet traffic information will be recorded.

xAppleRemoteAccess

1.3.6.1.4.1.33.21.6

STR arapPassword

1.3.6.1.4.1.33.21.6.1

DisplayString

read-write

The server's ARAP password. To increase security, Gets of this object return the NULL string.

STR arapDefaultZoneName

1.3.6.1.4.1.33.21.6.2

DisplayString

read-write

The name of the AppleTalk zone that the server should try to choose at boot time.

arapPortTable

1.3.6.1.4.1.33.21.6.3

not-accessible

A list of ARAP port entries.

arapPortEntry

1.3.6.1.4.1.33.21.6.3.1

not-accessible

ARAP parameter values for a port.

INT arapPortEnabled

1.3.6.1.4.1.33.21.6.3.1.1

INTEGER

read-write

Indicates if ARAP connections are allowed on this port.

INT arapPortZoneAccess

1.3.6.1.4.1.33.21.6.3.1.2

INTEGER

read-write

Indicates the AppleTalk zones that ARAP connections on this port may access: none, local, all, or named zone.

STR arapPortZoneName

1.3.6.1.4.1.33.21.6.3.1.3

DisplayString

read-write

If this port's arapPortZoneAccess field indicates a named zone, this field contains the zone name.

INT arapPortMaxConnectTime

1.3.6.1.4.1.33.21.6.3.1.4

INTEGER

read-write

Maximum number of minutes a single ARAP connection may exist on the port before a server initiated disconnect. To set no limit on the amount of time that an ARAP user may be connected, set this object to -1.

INT arapPortGuestLoginsOk

1.3.6.1.4.1.33.21.6.3.1.5

INTEGER

read-write

Indicates if 'Guest' logins (with no password) are allowed on the port.

INT arapPortTimeConnected

1.3.6.1.4.1.33.21.6.3.1.6

INTEGER

read-only

Indicates the number of minutes the current ARAP connection has been established on the port, rounded up to the nearest minute. Gets return -1 if no ARAP user is currently connected on the port or if ARAP is not enabled on the port.

INT arapPortTimeRemaining

1.3.6.1.4.1.33.21.6.3.1.7

INTEGER

read-write

Indicates the number of minutes the current ARAP connection may remain on the port before a server initiated disconnect will occur, rounded up to the nearest minute. To set no limit on the amount of time that the current ARAP user may continue to be connected, set this object to the maximum value in the range. Gets return -1 if no ARAP user is currently connected on the port or if ARAP is not enabled on the port. Gets also return -1 if there is a user connected and there is no limit on the amount of time that the current user may be connected.

xPpp

1.3.6.1.4.1.33.22

xPppBasic

1.3.6.1.4.1.33.22.1

xPppConfigTable

1.3.6.1.4.1.33.22.1.1

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppConfigEntry

1.3.6.1.4.1.33.22.1.1.1

not-accessible

Management information about a particular PPP.

INT xPppConfigOpen

1.3.6.1.4.1.33.22.1.1.1.1

INTEGER

read-write

Determines if PPP is configured on this port.

INT xPppConfigActive

1.3.6.1.4.1.33.22.1.1.1.2

INTEGER

read-write

Determines if LCP will actively open or wait passively.

INT xPppConfigDefaults

1.3.6.1.4.1.33.22.1.1.1.3

INTEGER

read-write

Revert to factory default PPP parameters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' sets PPP parameters to factory defaults.

INT xPppConfigRestartTimer

1.3.6.1.4.1.33.22.1.1.1.4

INTEGER

read-write

The number of seconds waited before retransmitting during option negotiation.

INT xPppConfigConfLimit

1.3.6.1.4.1.33.22.1.1.1.5

INTEGER

read-write

Maximum number of times a configuration request will be sent to the peer without receiving a response.

INT xPppConfigFailLimit

1.3.6.1.4.1.33.22.1.1.1.6

INTEGER

read-write

Maximum number of times a peer's proposed option will be NAKed before REJECTing the option.

INT xPppConfigPacketLogging

1.3.6.1.4.1.33.22.1.1.1.7

INTEGER

read-write

Determines the level of packet logging to accounting on this port.

INT xPppConfigKATimer

1.3.6.1.4.1.33.22.1.1.1.8

INTEGER

read-write

Determines the number of seconds between transmission of LCP Echo Keepalive packets.

INT xPppConfigKATimeout

1.3.6.1.4.1.33.22.1.1.1.9

INTEGER

read-write

Determines the number of seconds to wait to hear LCP Echo Replies to our Echo Request Keepalive packets before giving up and shutting down the link.

xPppStatusTable

1.3.6.1.4.1.33.22.1.2

not-accessible

A table containing basic PPP status info.

xPppStatusEntry

1.3.6.1.4.1.33.22.1.2.1

not-accessible

Status information about a particular PPP.

INT xPppStatusState

1.3.6.1.4.1.33.22.1.2.1.1

INTEGER

read-only

Displays whether PPP is enabled or disabled on this port.

INT xPppLinkOpen

1.3.6.1.4.1.33.22.1.2.1.2

INTEGER

read-only

Displays open status of the link.

CTR xPppHdlcRxTotalPkts

1.3.6.1.4.1.33.22.1.2.1.3

Counter

read-only

Total of all packets received on PPP link.

CTR xPppHdlcTxTotalPkts

1.3.6.1.4.1.33.22.1.2.1.4

Counter

read-only

Total of all packets transmitted on PPP link.

CTR xPppHdlcRxFrameErrs

1.3.6.1.4.1.33.22.1.2.1.5

Counter

read-only

Number of framing errors received on PPP link.

CTR xPppHdlcRxNoBuffer

1.3.6.1.4.1.33.22.1.2.1.6

Counter

read-only

Number of times a buffer was not available to receive packet into.

CTR xPppHdlcTxNoBuffer

1.3.6.1.4.1.33.22.1.2.1.7

Counter

read-only

Number of times a buffer was not available to transmit a packet from.

CTR xPppHdlcRxBadFcs

1.3.6.1.4.1.33.22.1.2.1.8

Counter

read-only

Number of packets received with a bad checksum.

CTR xPppHdlcVJDiscards

1.3.6.1.4.1.33.22.1.2.1.9

Counter

read-only

Number of packets received that failed VJ decompression.

xPppLcp

1.3.6.1.4.1.33.22.2

xPppLcpConfigTable

1.3.6.1.4.1.33.22.2.1

not-accessible

A table containing PPP LCP specific variables for this PPP implementation.

xPppLcpConfigEntry

1.3.6.1.4.1.33.22.2.1.1

not-accessible

Management information about a particular PPP LCP session.

INT xPppLcpConfigAuth

1.3.6.1.4.1.33.22.2.1.1.1

INTEGER

read-write

Authentication protocol used for authenticating peers.

INT xPppLcpConfigChapAuth

1.3.6.1.4.1.33.22.2.1.1.2

INTEGER

read-write

Authentication CHAP protocol used for authenticating peers.

xPppLcpStatusTable

1.3.6.1.4.1.33.22.2.2

not-accessible

A table containing PPP LCP status info.

xPppLcpStatusEntry

1.3.6.1.4.1.33.22.2.2.1

not-accessible

Status information about a particular PPP LCP session.

INT xPppLcpStatusState

1.3.6.1.4.1.33.22.2.2.1.1

INTEGER

read-only

The current state of LCP.

INT xPppLcpStatusRxAuth

1.3.6.1.4.1.33.22.2.2.1.2

INTEGER

read-only

The authentication protocol currently in use from the peer to us.

INT xPppLcpStatusTxAuth

1.3.6.1.4.1.33.22.2.2.1.3

INTEGER

read-only

The authentication protocol currently in use from us to the peer.

CTR xPppLcpStatusRxConReq

1.3.6.1.4.1.33.22.2.2.1.4

Counter

read-only

The count of LCP Configure Requests received from the peer.

CTR xPppLcpStatusTxConReq

1.3.6.1.4.1.33.22.2.2.1.5

Counter

read-only

The count of LCP Configure Requests transmitted to the peer.

CTR xPppLcpStatusRxConNak

1.3.6.1.4.1.33.22.2.2.1.6

Counter

read-only

The count of LCP Configure Naks received from the peer.

CTR xPppLcpStatusTxConNak

1.3.6.1.4.1.33.22.2.2.1.7

Counter

read-only

The count of LCP Configure Naks transmitted to the peer.

CTR xPppLcpStatusRxConAck

1.3.6.1.4.1.33.22.2.2.1.8

Counter

read-only

The count of LCP Configure Acks received from the peer.

CTR xPppLcpStatusTxConAck

1.3.6.1.4.1.33.22.2.2.1.9

Counter

read-only

The count of LCP Configure Acks transmitted to the peer.

CTR xPppLcpStatusRxConRej

1.3.6.1.4.1.33.22.2.2.1.10

Counter

read-only

The count of LCP Configure Rejects received from the peer.

CTR xPppLcpStatusTxConRej

1.3.6.1.4.1.33.22.2.2.1.11

Counter

read-only

The count of LCP Configure Rejects transmitted to the peer.

CTR xPppLcpStatusRxTrmReq

1.3.6.1.4.1.33.22.2.2.1.12

Counter

read-only

The count of LCP Terminate Requests received from the peer.

CTR xPppLcpStatusTxTrmReq

1.3.6.1.4.1.33.22.2.2.1.13

Counter

read-only

The count of LCP Terminate Requests transmitted to the peer.

CTR xPppLcpStatusRxTrmAck

1.3.6.1.4.1.33.22.2.2.1.14

Counter

read-only

The count of LCP Terminate Acks received from the peer.

CTR xPppLcpStatusTxTrmAck

1.3.6.1.4.1.33.22.2.2.1.15

Counter

read-only

The count of LCP Terminate Acks transmitted to the peer.

CTR xPppLcpStatusRxEcoReq

1.3.6.1.4.1.33.22.2.2.1.16

Counter

read-only

The count of LCP Echo Requests received from the peer.

CTR xPppLcpStatusTxEcoReq

1.3.6.1.4.1.33.22.2.2.1.17

Counter

read-only

The count of LCP Echo Requests transmitted to the peer.

CTR xPppLcpStatusRxEcoRep

1.3.6.1.4.1.33.22.2.2.1.18

Counter

read-only

The count of LCP Echo Reply received from the peer.

CTR xPppLcpStatusTxEcoRep

1.3.6.1.4.1.33.22.2.2.1.19

Counter

read-only

The count of LCP Echo Reply transmitted to the peer.

CTR xPppLcpStatusRxCodRej

1.3.6.1.4.1.33.22.2.2.1.20

Counter

read-only

The count of LCP Code Rejects received from the peer.

CTR xPppLcpStatusTxCodRej

1.3.6.1.4.1.33.22.2.2.1.21

Counter

read-only

The count of LCP Code Rejects transmitted to the peer.

CTR xPppLcpStatusRxProRej

1.3.6.1.4.1.33.22.2.2.1.22

Counter

read-only

The count of LCP Protocol Rejects received from the peer.

CTR xPppLcpStatusTxProRej

1.3.6.1.4.1.33.22.2.2.1.23

Counter

read-only

The count of LCP Protocol Rejects transmitted to the peer.

INT xPppLcpStatusState2

1.3.6.1.4.1.33.22.2.2.1.24

INTEGER

read-only

The current state of LCP.

xPppIpcp

1.3.6.1.4.1.33.22.3

xPppIpcpConfigTable

1.3.6.1.4.1.33.22.3.1

not-accessible

A table containing PPP IPCPspecific variables for this PPP implementation.

xPppIpcpConfigEntry

1.3.6.1.4.1.33.22.3.1.1

not-accessible

Management information about a particular PPP IPCP session.

IP xPppIpcpConfigLocalAddress

1.3.6.1.4.1.33.22.3.1.1.1

IpAddress

read-write

IP Address of the local PPP interface.

IP xPppIpcpConfigRemoteAddress

1.3.6.1.4.1.33.22.3.1.1.2

IpAddress

read-write

IP Address of the peer PPP interface.

INT xPppIpcpConfigVJCompSlots

1.3.6.1.4.1.33.22.3.1.1.3

INTEGER

read-write

Number of slots to be used by VJ compression.

IP xPppIpcpConfigRangeStart

1.3.6.1.4.1.33.22.3.1.1.4

IpAddress

read-write

Start of acceptable address range in which the negotiated remote IP address must fall.

IP xPppIpcpConfigRangeEnd

1.3.6.1.4.1.33.22.3.1.1.5

IpAddress

read-write

End of acceptable address range in which the negotiated remote IP address must fall.

INT xPppIpcpConfigState

1.3.6.1.4.1.33.22.3.1.1.6

INTEGER

read-write

Controls whether IPCP is allowed to run on this port.

IP xPppIpcpConfigLocalRangeStart

1.3.6.1.4.1.33.22.3.1.1.7

IpAddress

read-write

Start of acceptable address range in which the negotiated local IP address must fall.

IP xPppIpcpConfigLocalRangeEnd

1.3.6.1.4.1.33.22.3.1.1.8

IpAddress

read-write

End of acceptable address range in which the negotiated local IP address must fall.

IP xPppIpcpConfigPppIpMask

1.3.6.1.4.1.33.22.3.1.1.9

IpAddress

read-write

The subnet mask to use for a PPP operation on the port. Corresponds directly to the value labeled 'IP Mask:' in the PPP PORT IP CHARACTERISTICS display.

xPppIpcpAsyncConfigTable

1.3.6.1.4.1.33.22.3.2

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppIpcpAsyncConfigEntry

1.3.6.1.4.1.33.22.3.2.1

not-accessible

Management information about a particular PPP Asynchronous LCP.

INT xPppIpcpAsyncConfigBrdcast

1.3.6.1.4.1.33.22.3.2.1.1

INTEGER

read-write

Determines whether to forward an IP Broadcast or not.

xPppIpcpStatusTable

1.3.6.1.4.1.33.22.3.3

not-accessible

A table containing basic PPP IPCP status info.

xPppIpcpStatusEntry

1.3.6.1.4.1.33.22.3.3.1

not-accessible

Status information about a particular PPP IPCP session.

INT xPppIpcpStatusState

1.3.6.1.4.1.33.22.3.3.1.1

INTEGER

read-only

The current state of IPCP.

IP xPppIpcpStatusLocalAddress

1.3.6.1.4.1.33.22.3.3.1.2

IpAddress

read-only

The IP Address currently being used by the local IPCP.

IP xPppIpcpStatusRemoteAddress

1.3.6.1.4.1.33.22.3.3.1.3

IpAddress

read-only

The IP Address currently being used by the Remote IPCP.

CTR xPppIpcpRxPkts

1.3.6.1.4.1.33.22.3.3.1.4

Counter

read-only

Total number of IP packets received.

CTR xPppIpcpTxPkts

1.3.6.1.4.1.33.22.3.3.1.5

Counter

read-only

Total number of IP packets transmitted.

CTR xPppIpcpRxConReq

1.3.6.1.4.1.33.22.3.3.1.6

Counter

read-only

The count of IPCP Configure Requests received from the peer.

CTR xPppIpcpTxConReq

1.3.6.1.4.1.33.22.3.3.1.7

Counter

read-only

The count of IPCP Configure Requests transmitted to the peer.

CTR xPppIpcpRxConNak

1.3.6.1.4.1.33.22.3.3.1.8

Counter

read-only

The count of IPCP Configure Naks received from the peer.

CTR xPppIpcpTxConNak

1.3.6.1.4.1.33.22.3.3.1.9

Counter

read-only

The count of IPCP Configure Naks transmitted to the peer.

CTR xPppIpcpRxConAck

1.3.6.1.4.1.33.22.3.3.1.10

Counter

read-only

The count of IPCP Configure Acks received from the peer.

CTR xPppIpcpTxConAck

1.3.6.1.4.1.33.22.3.3.1.11

Counter

read-only

The count of IPCP Configure Acks transmitted to the peer.

CTR xPppIpcpRxConRej

1.3.6.1.4.1.33.22.3.3.1.12

Counter

read-only

The count of IPCP Configure Rejects received from the peer.

CTR xPppIpcpTxConRej

1.3.6.1.4.1.33.22.3.3.1.13

Counter

read-only

The count of IPCP Configure Rejects transmitted to the peer.

CTR xPppIpcpRxTrmReq

1.3.6.1.4.1.33.22.3.3.1.14

Counter

read-only

The count of IPCP Terminate Requests received from the peer.

CTR xPppIpcpTxTrmReq

1.3.6.1.4.1.33.22.3.3.1.15

Counter

read-only

The count of IPCP Terminate Requests transmitted to the peer.

CTR xPppIpcpRxTrmAck

1.3.6.1.4.1.33.22.3.3.1.16

Counter

read-only

The count of IPCP Terminate Acks received from the peer.

CTR xPppIpcpTxTrmAck

1.3.6.1.4.1.33.22.3.3.1.17

Counter

read-only

The count of IPCP Terminate Acks transmitted to the peer.

INT xPppIpcpStatusState2

1.3.6.1.4.1.33.22.3.3.1.18

INTEGER

read-only

The current state of IPCP.

xPppAuth

1.3.6.1.4.1.33.22.4

OCT xPppPapPassword

1.3.6.1.4.1.33.22.4.1

OCTET STRING

read-write

The password to use for PAP authentication.

xPppAuthConfigTable

1.3.6.1.4.1.33.22.4.2

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppAuthConfigEntry

1.3.6.1.4.1.33.22.4.2.1

not-accessible

Management information about a particular PPP.

INT xPppAuthChapChallengeTimer

1.3.6.1.4.1.33.22.4.2.1.4

INTEGER

read-write

Length of time in minutes between CHAP reauthentication challenges. A value of zero disables the timer.

INT xPppAuthPapConfigState

1.3.6.1.4.1.33.22.4.2.1.5

INTEGER

read-write

Controls the type of Pap authentication required for this port, and whether it is combined with another authentication mechanism such as Radius.

INT xPppAuthChapConfigState

1.3.6.1.4.1.33.22.4.2.1.6

INTEGER

read-write

Controls the type of Chap authentication required for this port, and whether it is combined with another authentication mechanism such as Radius.

xPppAuthStatusTable

1.3.6.1.4.1.33.22.4.3

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppAuthStatusEntry

1.3.6.1.4.1.33.22.4.3.1

not-accessible

Management information about a particular PPP.

INT xPppPapStatusState

1.3.6.1.4.1.33.22.4.3.1.4

INTEGER

read-only

The current state of PAP.

INT xPppChapStatusState

1.3.6.1.4.1.33.22.4.3.1.5

INTEGER

read-only

The current state of CHAP.

OCT xPppChapPassword

1.3.6.1.4.1.33.22.4.4

OCTET STRING

read-write

The password to use for CHAP authentication.

xPppIpxcp

1.3.6.1.4.1.33.22.5

xPppIpxcpConfigTable

1.3.6.1.4.1.33.22.5.1

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppIpxcpConfigEntry

1.3.6.1.4.1.33.22.5.1.1

not-accessible

Management information about a particular PPP.

INT xPppIpxcpCipxCompression

1.3.6.1.4.1.33.22.5.1.1.1

INTEGER

read-write

Controls whether CIPX compression will be negotiated on the interface.

OCT xPppIpxcpConfigRemoteNode

1.3.6.1.4.1.33.22.5.1.1.2

OCTET STRING

read-write

The IPX Node address which can be offered to the peer if it does not know a Node number but requires one.

xPppIpxcpStatusTable

1.3.6.1.4.1.33.22.5.2

not-accessible

A table containing PPP specific variables for this PPP implementation.

xPppIpxcpStatusEntry

1.3.6.1.4.1.33.22.5.2.1

not-accessible

Management information about a particular PPP.

INT xPppIpxcpStatusState

1.3.6.1.4.1.33.22.5.2.1.1

INTEGER

read-only

The current state of IPXCP.

INT xPppIpxcpCipxInCompression

1.3.6.1.4.1.33.22.5.2.1.2

INTEGER

read-only

The current state of CIPX compression inbound.

INT xPppIpxcpCipxOutCompression

1.3.6.1.4.1.33.22.5.2.1.3

INTEGER

read-only

The current state of CIPX compression outbound.

INT xPppIpxcpCipxInSlots

1.3.6.1.4.1.33.22.5.2.1.4

INTEGER

read-only

The current number of CIPX compression inbound slots.

INT xPppIpxcpCipxOutSlots

1.3.6.1.4.1.33.22.5.2.1.5

INTEGER

read-only

The current number of CIPX compression outbound slots.

OCT xPppIpxcpStatusRemoteNode

1.3.6.1.4.1.33.22.5.2.1.6

OCTET STRING

read-only

The IPX Node address currently being used by the Remote IPX peer.

xPppIpxcpCountersTable

1.3.6.1.4.1.33.22.5.3

not-accessible

A table containing basic PPP IPXCP status info.

xPppIpxcpCountersEntry

1.3.6.1.4.1.33.22.5.3.1

not-accessible

Counter information about a particular PPP IPXCP session.

CTR xPppIpxcpRxConReq

1.3.6.1.4.1.33.22.5.3.1.1

Counter

read-only

The count of IPXCP Configure Requests received from the peer.

CTR xPppIpxcpTxConReq

1.3.6.1.4.1.33.22.5.3.1.2

Counter

read-only

The count of IPXCP Configure Requests transmitted to the peer.

CTR xPppIpxcpRxConNak

1.3.6.1.4.1.33.22.5.3.1.3

Counter

read-only

The count of IPXCP Configure Naks received from the peer.

CTR xPppIpxcpTxConNak

1.3.6.1.4.1.33.22.5.3.1.4

Counter

read-only

The count of IPXCP Configure Naks transmitted to the peer.

CTR xPppIpxcpRxConAck

1.3.6.1.4.1.33.22.5.3.1.5

Counter

read-only

The count of IPXCP Configure Acks received from the peer.

CTR xPppIpxcpTxConAck

1.3.6.1.4.1.33.22.5.3.1.6

Counter

read-only

The count of IPXCP Configure Acks transmitted to the peer.

CTR xPppIpxcpRxConRej

1.3.6.1.4.1.33.22.5.3.1.7

Counter

read-only

The count of IPXCP Configure Rejects received from the peer.

CTR xPppIpxcpTxConRej

1.3.6.1.4.1.33.22.5.3.1.8

Counter

read-only

The count of IPXCP Configure Rejects transmitted to the peer.

CTR xPppIpxcpRxTrmReq

1.3.6.1.4.1.33.22.5.3.1.9

Counter

read-only

The count of IPXCP Terminate Requests received from the peer.

CTR xPppIpxcpTxTrmReq

1.3.6.1.4.1.33.22.5.3.1.10

Counter

read-only

The count of IPXCP Terminate Requests transmitted to the peer.

CTR xPppIpxcpRxTrmAck

1.3.6.1.4.1.33.22.5.3.1.11

Counter

read-only

The count of IPXCP Terminate Acks received from the peer.

CTR xPppIpxcpTxTrmAck

1.3.6.1.4.1.33.22.5.3.1.12

Counter

read-only

The count of IPXCP Terminate Acks transmitted to the peer.

xRadius

1.3.6.1.4.1.33.35

xRadiusPort

1.3.6.1.4.1.33.35.1

xRadiusPortTable

1.3.6.1.4.1.33.35.1.1

not-accessible

Table of fields indexed by port.

xRadiusPortEntry

1.3.6.1.4.1.33.35.1.1.1

not-accessible

A particular entry.

INT xRadiusPortIndex

1.3.6.1.4.1.33.35.1.1.1.1

INTEGER

read-only

The index of the port.

INT xRadiusPortStatus

1.3.6.1.4.1.33.35.1.1.1.2

INTEGER

read-only

Indicates the state of Radius Authentication on the port.

INT xRadiusPortSolicitStatus

1.3.6.1.4.1.33.35.1.1.1.3

INTEGER

read-write

Indicates the state of Radius solicitation mode on the port.

INT xRadiusAcctPortStatus

1.3.6.1.4.1.33.35.1.1.1.4

INTEGER

read-only

Indicates the state of Radius Accounting on the port.

xRadiusCircuit

1.3.6.1.4.1.33.35.2

xRadiusConfig

1.3.6.1.4.1.33.35.3

INT xRadiusAuthServerPort

1.3.6.1.4.1.33.35.3.1

INTEGER

read-write

The UDP port on which the Radius authentication request will be made.

INT xRadiusAcctServerPort

1.3.6.1.4.1.33.35.3.2

INTEGER

read-write

The UDP port on which the Radius accounting request will be made.

INT xRadiusTimeout

1.3.6.1.4.1.33.35.3.3

INTEGER

read-write

The period of time that the Radius client will wait for a reply from the server.

INT xRadiusServerRetries

1.3.6.1.4.1.33.35.3.4

INTEGER

read-write

The number of times a Radius server will be tried.

INT xRadiusAcctLogAttempts

1.3.6.1.4.1.33.35.3.5

INTEGER

read-write

The number of times the client will attempt to log the accounting record to either the primary or secondary Radius server before giving up and failing.

INT xRadiusChapChallengeSize

1.3.6.1.4.1.33.35.3.6

INTEGER

read-write

The size of the CHAP challenge that is sent to the peer and the Radius server.

INT xRadiusLogging

1.3.6.1.4.1.33.35.3.7

INTEGER

read-write

Indicates the state of Radius logging for packet tracing and troubleshooting. Messages are logged to the MRV In-Reach event log.

STR xRadiusMessage

1.3.6.1.4.1.33.35.3.8

DisplayString

read-write

The authentication prompting message for Radius logins.

xRadiusServers

1.3.6.1.4.1.33.35.4

xRadServer1SubGrp

1.3.6.1.4.1.33.35.4.1

OCT xRadiusServerName1

1.3.6.1.4.1.33.35.4.1.1

OCTET STRING

read-write

The primary Radius server queried for authentication.

OCT xRadiusSecret1

1.3.6.1.4.1.33.35.4.1.2

OCTET STRING

read-only

The secret value used to communicate with the primary Radius server.

CTR xRadiusServerAccess1

1.3.6.1.4.1.33.35.4.1.3

Counter

read-only

The number of successful accesses of primary Radius server.

CTR xRadiusServerAccessFailed1

1.3.6.1.4.1.33.35.4.1.4

Counter

read-only

The number of failed accesses of primary Radius server.

xRadServer2SubGrp

1.3.6.1.4.1.33.35.4.2

OCT xRadiusServerName2

1.3.6.1.4.1.33.35.4.2.1

OCTET STRING

read-write

The secondary Radius server queried for authentication, if the primary one fails.

OCT xRadiusSecret2

1.3.6.1.4.1.33.35.4.2.2

OCTET STRING

read-only

The secret value used to communicate with the secondary Radius server.

CTR xRadiusServerAccess2

1.3.6.1.4.1.33.35.4.2.3

Counter

read-only

The number of successful accesses of secondary Radius server.

CTR xRadiusServerAccessFailed2

1.3.6.1.4.1.33.35.4.2.4

Counter

read-only

The number of failed accesses of secondary Radius server.

xRadiusCounters

1.3.6.1.4.1.33.35.5

xRadAuthCtsSubGrp

1.3.6.1.4.1.33.35.5.1

CTR xRadiusLogins

1.3.6.1.4.1.33.35.5.1.1

Counter

read-only

The number of successful logins using Radius.

CTR xRadiusLoginsFailed

1.3.6.1.4.1.33.35.5.1.2

Counter

read-only

The number of failed logins resulting from being rejected by the Radius server.

CTR xRadiusConfigFailed

1.3.6.1.4.1.33.35.5.1.3

Counter

read-only

The number of failed logins resulting from unsupported attribute values.

CTR xRadiusPolicyFailed

1.3.6.1.4.1.33.35.5.1.4

Counter

read-only

The number of failed logins resulting from failing specific Radius policies on the MRV In-Reach unit.

xRadAcctCtsSubGrp

1.3.6.1.4.1.33.35.5.2

CTR xRadiusAcctSuccess

1.3.6.1.4.1.33.35.5.2.1

Counter

read-only

The number of successfully recorded Radius accounting log records.

CTR xRadiusAcctFailed

1.3.6.1.4.1.33.35.5.2.2

Counter

read-only

The number of failed (not logged) Radius accounting log records.

CTR xRadiusAcctReqWait

1.3.6.1.4.1.33.35.5.2.3

Counter

read-only

The number of log requests waiting for a reply from the Radius server.

xAlarm

1.3.6.1.4.1.33.49