All MIBs › Juniper-PPPOE-MIB › juniPPPoEIfLockoutMin
juniPPPoEIfLockoutMin
Module: Juniper-PPPOE-MIB
OID (symbolic): Juniper-PPPOE-MIB::juniPPPoEIfLockoutMin
OID (numeric): 1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: The lower bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if juniPPPoEIfAutoconfig is set for this interface.
The ability to lockout the client in the event of an error in creating a PPP interface is enabled by default. The initial lockout duration is this object's value and increases exponentially for each failure that occurs for the client creating a PPP interface for the PPPoE interface within the greater of 15 minutes and juniPPPoEIfLockoutMax.
The lockout duration for the client will not exceed juniPPPoEIfLockoutMax. If the time between creation errors for the PPP interface for this interface is greater than the greater of 15 minutes and juniPPPoEIfLockoutMax, then the lockout duration reverts to this object's value.
To disable the ability to lockout the client from recognition in the event of an error in creating a PPP interface for the specified interface, the value of this object and juniPPPoEIfLockoutMin must be set to 0. It is not recommended that this lockout feature be disabled except for debugging purposes or when this interface supports more than one session.
What is juniPPPoEIfLockoutMin?
This sets, in seconds (0-86400) and defaulting to 0, the initial lockout duration applied to a client after a PPP interface creation error on this autoconfig-enabled interface; the lockout time then increases exponentially on repeated failures up to juniPPPoEIfLockoutMax, and setting both this and Max to 0 disables client lockout.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12 snmpwalk -v2c -c public <target> Juniper-PPPOE-MIB::juniPPPoEIfLockoutMin
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12.1 snmpget -v2c -c public <target> Juniper-PPPOE-MIB::juniPPPoEIfLockoutMin.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12.1 i <value>
Start monitoring Juniper E-series broadband edge router (PPPoE interfaces/subinterfaces) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Juniper-PPPOE-MIB::juniPPPoEIfLockoutMin OID value, configure state conditions and alerts, and monitor any Juniper E-series broadband edge router (PPPoE interfaces/subinterfaces) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.4874 | juniperUni | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2 | juniperUniMibs | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2.2 | juniMibs | Juniper-MIBs |
| 1.3.6.1.4.1.4874.2.2.18 | juniPPPoEMIB | Juniper-MIBs |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4874.2.2.18.1 | juniPPPoEObjects | Juniper-PPPOE-MIB |
| 1.3.6.1.4.1.4874.2.2.18.1.1 | juniPPPoEIfLayer | Juniper-PPPOE-MIB |
| 1.3.6.1.4.1.4874.2.2.18.1.1.2 | juniPPPoEIfTable | Juniper-PPPOE-MIB |
| 1.3.6.1.4.1.4874.2.2.18.1.1.2.1 | juniPPPoEIfEntry | Juniper-PPPOE-MIB |
| 1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12 | juniPPPoEIfLockoutMin | Juniper-PPPOE-MIB |