All MIBs › ESAFE-MIB › esafeErouterAdminMode
esafeErouterAdminMode
Module: ESAFE-MIB
OID (symbolic): ESAFE-MIB::esafeErouterAdminMode
OID (numeric): 1.3.6.1.4.1.4491.2.1.14.1.5.1
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-only
Description: This object provides visibility to the eRouter mode of operation as specified by TLV 202.1. If the value of this object is disabled(1), the eRouter was configured via TLV 202.1 in the cable modem configuration file to not initialize as described in the eRouter Initialization section of the CableLabs IPv4 and IPv6 eRouter Specification.
If the value of this object is ipv4Only(2), the eRouter was configured via TLV 202.1 in the cable modem configuration file to operate with an IPv4 network address and with the IPv4 stack operational and to operate without an IPv6 network address and to not run an IPv6 protocol stack.
If the value of this object is ipv6Only(3), the eRouter was configured via TLV 202.1 in the cable modem configuration file to operate with an IPv6 network address and with the IPv6 stack operational and to operate without an IPv4 network address and to not run an IPv4 protocol stack.
If the value of this object is ipv4AndIpv6(4), the eRouter was configured via TLV 202.1 in the cable modem configuration file to operate with an IPv4 network address and an IPv6 network address and to run both IPv4 and IPv6 protocol stacks.
If the value of the object is noTLV202dot1Present(5), the eRouter was not configured via TLV 202.1 in the cable modem configuration file.
What is esafeErouterAdminMode?
This reports the eRouter's configured operating mode as specified by TLV 202.1 in the cable modem's configuration file. An admin reads it to see what IP protocol mode the eRouter was told to run, or that no TLV 202.1 was present at all, distinct from esafeErouterOperMode which shows the actual running mode. For example, a config file specifying ipv4AndIpv6(4) tells the admin the eRouter was configured for dual-stack, while noTLV202dot1Present(5) flags that the TLV was never set.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.4491.2.1.14.1.5.1 snmpwalk -v2c -c public <target> ESAFE-MIB::esafeErouterAdminMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.4491.2.1.14.1.5.1.1 snmpget -v2c -c public <target> ESAFE-MIB::esafeErouterAdminMode.1
Start monitoring Cable modem/gateway with embedded eSAFE service applications (DOCSIS CPE) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the ESAFE-MIB::esafeErouterAdminMode OID value, configure state conditions and alerts, and monitor any Cable modem/gateway with embedded eSAFE service applications (DOCSIS CPE) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.4491 | cableLabs | CLAB-DEF-MIB |
| 1.3.6.1.4.1.4491.2 | clabProject | CLAB-DEF-MIB |
| 1.3.6.1.4.1.4491.2.1 | clabProjDocsis | CLAB-DEF-MIB |
| 1.3.6.1.4.1.4491.2.1.14 | esafeMib | CLAB-DEF-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4491.2.1.14.1 | esafeMibObjects | ESAFE-MIB |
| 1.3.6.1.4.1.4491.2.1.14.1.5 | esafeErouterMibObjects | ESAFE-MIB |
| 1.3.6.1.4.1.4491.2.1.14.1.5.1 | esafeErouterAdminMode | ESAFE-MIB |