All MIBs › DOT12-RPTR-MIB › vgRptrMonTotalReadableOctets
vgRptrMonTotalReadableOctets
Module: DOT12-RPTR-MIB
OID (symbolic): DOT12-RPTR-MIB::vgRptrMonTotalReadableOctets
OID (numeric): 1.3.6.1.2.1.53.1.2.1.1.1.2
Node type: OBJECT-TYPE
Type: Counter32
Access: read-only
Description: The total number of octets contained in good frames that have been received on all ports in this repeater. If an implementation cannot
obtain a count of octets as seen by the repeater itself, this counter may be implemented as the summation of the values of the vgRptrPortReadableOctets counters for all of the ports in this repeater.
Note that this counter can roll over very quickly. A management station is advised to also poll the vgRptrReadableOctetRollovers object, or to use the 64-bit counter defined by vgRptrMonHCTotalReadableOctets instead of the two 32-bit counters.
This two-counter mechanism is provided for those network management protocols that do not support 64-bit counters (e.g. SNMPv1). Note that retrieval of these two counters in the same PDU is NOT guaranteed to be atomic.
This counter may experience a discontinuity when the value of the corresponding instance of vgRptrInfoLastChange changes.
What is vgRptrMonTotalReadableOctets?
A 32-bit running total of octets in good frames received across all ports of this repeater, which can roll over quickly; the MIB recommends pairing it with vgRptrMonReadableOctetRollovers or using the 64-bit vgRptrMonHCTotalReadableOctets instead. An admin uses this to measure repeater-wide throughput when only SNMPv1 32-bit counters are available.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.2.1.53.1.2.1.1.1.2 snmpwalk -v2c -c public <target> DOT12-RPTR-MIB::vgRptrMonTotalReadableOctets
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.2.1.53.1.2.1.1.1.2.1 snmpget -v2c -c public <target> DOT12-RPTR-MIB::vgRptrMonTotalReadableOctets.1
Start monitoring IEEE 802.12 100VG-AnyLAN repeater/hub (vendor-neutral IETF standard) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the DOT12-RPTR-MIB::vgRptrMonTotalReadableOctets OID value, configure state conditions and alerts, and monitor any IEEE 802.12 100VG-AnyLAN repeater/hub (vendor-neutral IETF standard) from a single console.
OID Breakdown
Upper-level ancestors (6 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.2 | mgmt | AXON-MIB |
| 1.3.6.1.2.1 | mib_2 | AXON-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.2.1.53 | vgRptrMIB | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1 | vgRptrObjects | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1.2 | vgRptrMonitor | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1.2.1 | vgRptrMonRepeater | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1.2.1.1 | vgRptrMonitorTable | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1.2.1.1.1 | vgRptrMonitorEntry | DOT12-RPTR-MIB |
| 1.3.6.1.2.1.53.1.2.1.1.1.2 | vgRptrMonTotalReadableOctets | DOT12-RPTR-MIB |