All MIBs › CISCO-VOICE-ANALOG-IF-MIB › cvaIfEMCfgSignalType
cvaIfEMCfgSignalType
Module: CISCO-VOICE-ANALOG-IF-MIB
OID (symbolic): CISCO-VOICE-ANALOG-IF-MIB::cvaIfEMCfgSignalType
OID (numeric): 1.3.6.1.4.1.9.9.62.1.2.1.1.1
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The signaling type of E&M tie trunk interface. winkStart - the calling side seizes the line by going off-hook on its E lead but waits for a short off-hook 'wink' indication on its M lead from the called side before sending address information as DTMF digits. immediateDial - the calling side seizes the line by going off-hook on its E lead and sends sends address information as DTMF digits. delayDial - the calling side seizes the line by going off-hook on its E lead. After a timing interval, the calling side looks at the supervision from the called side. If the supervision is on-hook, the calling side starts sending information as DTMF digits; otherwise, the calling side waits until the called side goes on-hook and then starts sending address information. lmr - the e&m port is used to interface with Land Mobil Radio system. The e-lead and m-lead are not used in the traditional way. fgd - Feature Group D is an access switched services that provides access to Local Exchange Carrier of the public switched network. It is supported in North America only based on E&M wink-start. fgd-eana - Exchange Access North American signalling protocol of Feature Group D.
What is cvaIfEMCfgSignalType?
This read-write INTEGER selects the E&M tie trunk signaling type, such as winkStart (a brief off-hook 'wink' on the M lead confirms the call before address digits are sent) or immediateDial. An administrator configures this to match the E&M signaling expected by the connected PBX or tie-trunk equipment. For example, setting this to winkStart(1) requires the far end to send a wink confirmation before this interface proceeds with dialing.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.9.62.1.2.1.1.1 snmpwalk -v2c -c public <target> CISCO-VOICE-ANALOG-IF-MIB::cvaIfEMCfgSignalType
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.9.62.1.2.1.1.1.1 snmpget -v2c -c public <target> CISCO-VOICE-ANALOG-IF-MIB::cvaIfEMCfgSignalType.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.9.62.1.2.1.1.1.1 i <value>
Start monitoring Cisco ISR/voice gateways with analog FXS/FXO/E&M interfaces with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VOICE-ANALOG-IF-MIB::cvaIfEMCfgSignalType OID value, configure state conditions and alerts, and monitor any Cisco ISR/voice gateways with analog FXS/FXO/E&M interfaces from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.9 | ciscoMgmt | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.9.62 | ciscoVoiceAnalogIfMIB | CISCO-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.9.9.62.1 | cvaIfObjects | CISCO-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.9.9.62.1.2 | cvaIfEMObjects | CISCO-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.9.9.62.1.2.1 | cvaIfEMCfgTable | CISCO-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.9.9.62.1.2.1.1 | cvaIfEMCfgEntry | CISCO-VOICE-ANALOG-IF-MIB |
| 1.3.6.1.4.1.9.9.62.1.2.1.1.1 | cvaIfEMCfgSignalType | CISCO-VOICE-ANALOG-IF-MIB |