All MIBs › CISCO-METRO-PHY-MIB › cmPhyIfClockRate
cmPhyIfClockRate
Module: CISCO-METRO-PHY-MIB
OID (symbolic): CISCO-METRO-PHY-MIB::cmPhyIfClockRate
OID (numeric): 1.3.6.1.4.1.9.10.69.1.1.1.1.3
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: This object allows the management client to set the clock rate across the client side interface.
Due to hardware limitations, all values may not be supported. The default value of this object depends on the value of the cmPhyIfProtocol object. When the value of the cmPhyIfProtocol object is reset, the value of this object will be automatically set to the default for that protocol. In case of protocols that support multiple rates, the default value of this object will be the lowest rate possible for that protocol. For example, if the value of cmPhyIfProtocol is set to 'sonet', the default value of cmPhyIfClockRate is set to the OC-3 rate of 155520 kHz. If a non-default value is desired, then this object must be set after the cmPhyIfProtocol object has been reset. This object must be set to a supported clock rate when setting cmPhyIfProtocol to 'unknown'. In 2R mode of operation, this object is not applicable and will have a default value of 0.
The value of this object cannot be modified when the cmPhyIfMonitor object is set to 'true' for that interface. Also, this object is not applicable to trunk side interfaces.
What is cmPhyIfClockRate?
Configures the clock rate used across the client-side interface; supported values and the default depend on the configured interface protocol and hardware capabilities.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.69.1.1.1.1.3 snmpwalk -v2c -c public <target> CISCO-METRO-PHY-MIB::cmPhyIfClockRate
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.69.1.1.1.1.3.1 snmpget -v2c -c public <target> CISCO-METRO-PHY-MIB::cmPhyIfClockRate.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.69.1.1.1.1.3.1 i <value>
Start monitoring Cisco Metro Ethernet / DWDM optical switches with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-METRO-PHY-MIB::cmPhyIfClockRate OID value, configure state conditions and alerts, and monitor any Cisco Metro Ethernet / DWDM optical switches from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.9 | cisco | CAT2600-MIB |
| 1.3.6.1.4.1.9.10 | ciscoExperiment | CISCO-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.9.10.69 | ciscoMetroPhyMIB | CISCO-METRO-PHY-MIB |
| 1.3.6.1.4.1.9.10.69.1 | ciscoMetroPhyMIBObjects | CISCO-METRO-PHY-MIB |
| 1.3.6.1.4.1.9.10.69.1.1 | cmPhyIf | CISCO-METRO-PHY-MIB |
| 1.3.6.1.4.1.9.10.69.1.1.1 | cmPhyIfTable | CISCO-METRO-PHY-MIB |
| 1.3.6.1.4.1.9.10.69.1.1.1.1 | cmPhyIfEntry | CISCO-METRO-PHY-MIB |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.3 | cmPhyIfClockRate | CISCO-METRO-PHY-MIB |