All MIBs › BIANCA-BRICK-PMX-MIB › pmxIfLayer1State
pmxIfLayer1State
Module: BIANCA-BRICK-PMX-MIB
OID (symbolic): BIANCA-BRICK-PMX-MIB::pmxIfLayer1State
OID (numeric): 1.3.6.1.4.1.272.4.12.1.1.3
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: The layer 1 state of the primary rate interface
active(F1) active, framing and synchronisation is o.k. This is the only state where data-transmission is possible remote-alarm(F2) receipt of an RAI, remote alarm indication, from the remote side; The remote-alarm is also known as yellow alarm or distant alarm no-signal(F3) no signal is received, RAI will be transmitted. NOS is also known as red alarm . no-sync(F4) signal is received but synchronistation is not possible, RAI will be transmitted The received signal may also consist of contingous Ones crc-error(F5) signal and synchronisation are o.k. but signal has heavy crc errors, RAI will be transmitted power-on(F6) initial state after power was switched on (transient) resync(7) Setting Layer 1 State to resync can be used to force resynchronisation
The Layer1states are also visible in the isdnIfTable, but the state numbers are mapped to those of an BRI-Interface
What is pmxIfLayer1State?
The layer 1 state of the primary rate interface active(F1) active, framing and synchronisation is o.k. The pmxIfLayer1State reports sync status: active (data flowing), remote-alarm (carrier alarming), no-signal (red alarm), no-sync (resynchronizing). For example, typical values range from 1 to 10 depending on configuration.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.272.4.12.1.1.3 snmpwalk -v2c -c public <target> BIANCA-BRICK-PMX-MIB::pmxIfLayer1State
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.272.4.12.1.1.3.1 snmpget -v2c -c public <target> BIANCA-BRICK-PMX-MIB::pmxIfLayer1State.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.272.4.12.1.1.3.1 i <value>
Start monitoring bintec elmeg BIANCA/BRICK ISDN routers with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the BIANCA-BRICK-PMX-MIB::pmxIfLayer1State OID value, configure state conditions and alerts, and monitor any bintec elmeg BIANCA/BRICK ISDN routers from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.272 | bintec | BIANCA-BOX-ISDN-MIB |
| 1.3.6.1.4.1.272.4 | bibo | BIANCA-BOX-ISDN-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.272.4.12 | pmx | BIANCA-BRICK-PMX-MIB |
| 1.3.6.1.4.1.272.4.12.1 | pmxIfTable | BIANCA-BRICK-PMX-MIB |
| 1.3.6.1.4.1.272.4.12.1.1 | pmxIfEntry | BIANCA-BRICK-PMX-MIB |
| 1.3.6.1.4.1.272.4.12.1.1.3 | pmxIfLayer1State | BIANCA-BRICK-PMX-MIB |