All MIBs › BIANCA-BRICK-IP-MIB › ipExtRtDstIfMode
ipExtRtDstIfMode
Module: BIANCA-BRICK-IP-MIB
OID (symbolic): BIANCA-BRICK-IP-MIB::ipExtRtDstIfMode
OID (numeric): 1.3.6.1.4.1.272.4.5.4.1.13
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: This object describes different behavior depending on the ifOperStatus of the destination interface:
dialup-wait: The route matches, when the ifOperStatus of the destination interface is either up or dormant. If the status is dormant, the ifAdminStatus is set to dialup to bring the interface to the up state. The datagram will wait until the ifOperStatus reaches the up state.
For all other states, the routing tables will be searched for a different matching entry.
dialup-continue: The route matches, if the ifOperStatus of the destination interface is up. For all other states, the routing tables are searched for different matching entry. However, if the ifOperStatus was dormant, the ifAdminStatus will be set to dialup to bring the interface to the up state.
This setting can be used to establish a better path for a specific service and to use an existing path for that service as long as the better path could not be established.
up-only: The route matches, if the ifOperStatus of the destination interface is up. For all other states, the routing tables are searched for different matching entry.
always: The route matches independantly of the ifOperStatus of the destination interface. If it is up, the interface is used. If the state is dormant, ifAdminStatus is set to dialup to bring the interface in the up state. For all other states, the destination is considered unreachable.
What is ipExtRtDstIfMode?
This writable parameter specifies interface dependency behavior for an extended route. Values are dialup-wait (wait for interface if dormant), dialup-continue (skip if interface is not up), up-only (skip if not up), or always (use route regardless). Setting ipExtRtDstIfMode to 'always' uses this route even if the destination interface is administratively down.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.272.4.5.4.1.13 snmpwalk -v2c -c public <target> BIANCA-BRICK-IP-MIB::ipExtRtDstIfMode
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.272.4.5.4.1.13.1 snmpget -v2c -c public <target> BIANCA-BRICK-IP-MIB::ipExtRtDstIfMode.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.272.4.5.4.1.13.1 i <value>
Start monitoring bintec BIANCA/BRICK ISDN/VPN routers (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the BIANCA-BRICK-IP-MIB::ipExtRtDstIfMode OID value, configure state conditions and alerts, and monitor any bintec BIANCA/BRICK ISDN/VPN routers (legacy) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.272 | bintec | BIANCA-BOX-ISDN-MIB |
| 1.3.6.1.4.1.272.4 | bibo | BIANCA-BOX-ISDN-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.272.4.5 | biboip | BIANCA-BRICK-IP-MIB |
| 1.3.6.1.4.1.272.4.5.4 | ipExtRtTable | BIANCA-BRICK-IP-MIB |
| 1.3.6.1.4.1.272.4.5.4.1 | ipExtRtEntry | BIANCA-BRICK-IP-MIB |
| 1.3.6.1.4.1.272.4.5.4.1.13 | ipExtRtDstIfMode | BIANCA-BRICK-IP-MIB |