Description: Identification of cause for failure in changing the status of an interface. interfaceInService(1) Most, if not all, modifications require that the interface be out of service. interfaceNotNew(2) Some modifications require that the interface must never have been in service. interfaceExists(3) Some modifications, such as setting the interface type, require that no interface exists. (type must be unconfigured). bridgeGroupActive(4) For setting the bridgeDomainNumber in bridge or router interfaces. to add an interface to a bridgeGroup, the bridgeGroup must be in service. signalingNotEnabled(5) For this interface to be created, signaling must be enabled. firmwareOutOfDate(6) The firmware for the i/o card does not work with this interface. t1SigEnableInterfaceNotSupported(7) The interface is not supported if T1 signaling is enabled ts16ForData(8) ts16 has been set for passing data and the user attempts to turn on signaling. dbcesConfigured(9) Signaling cannot be disabled because this interface is configured as dbces. signalingEnabled(10) Signaling is on for at least one of the channels while trying to change e1 TS16 from CAS to CCS. cmCardTypeNotSupported(11) CM_NET interface is only supported by DS3 DS1 OC3 and SUPER_DS1 cards cmMultipleIntfNotSupported(12) only one interface can be configured as CM_NET cmIntfInService(13) CM_NET interface is in-service cmInterfaceConfigured(14) CM_NET interface is configured channelizationEnabled(15) A port can not be channelized in order to support unstructured CE. unstructuredCEConfigured(16) A port which has been channelized can not be configured to support unstructured CE. firmwareOutOfDate-ts16CAS-unsupported(17) ts16CAS is not supported by the firmware firmwareOutOfDate-interfaceType-unsupported(18) interface type is not supported by the firmware firmwareOutOfDate-ts16-unsupported(19) ts16 is not supported by the firmware invalidPortMap(20) invalid port map otherInterfacesExistOnThisPort(21) ISDN interface needs all 24 channels on the port. If any of the channels on that interface are already configured, the ISDN interface can not be defined on that port. intfInIMAgroup(22) chanId bit in portMap is 1 errorCTC-portTxClkSrc-notLocal(23) if imaGrpChannelNeTxClkMode is set to ctc then all ports should have the transmitClockSource as localTiming different-LoopbackConfig-on-Ports(24) all physical ports included in the portMap must have the same loopback configuration imaGChanNeTxClkMode-unsupported(25) ima group channel near-end Tx clock mode is not supported intfChange-Disallowed-on-APS-ProtectionPort(26) an interface cannot be manipulated via protection port in an APS setup intferfaceCurrentlyNotSupported(27) the interface type is not support currently failure-at-call-handler(28) interface creation failure due to call handler unstructuredCE-payloadloop(29) Unstructured CE should not have payload loopback as a loop back option channelConfigModeNotConforming(30) There was a limitation on the channel mode of DSP_2D card: if there is a channel is already inService, all the channel mode of configured channels must be the same as that of the channel inService; all the channel mode of unconfigured channels can only be configured the same as that of the channel inService. usageOfReservedTimeSlot(31) for HD_E1, do not allow any configuration to be SET on channel number 1 or 17 (base 1) or chan 0 or 16 (base 0). virtualIntf-and-AtmSignaling-bothCannotBeEnabled(32) vitual interface and signalling cannot both be enabled at the same time virtualUni-and-AtmSignaling-bothCannotBeEnabled(33) vitual UNI and signalling cannot both be enabled at the same time virtualUni-notSupported(34) virtual UNI is not supported atmUni-UbrLoadBalSupp-cannotBeEnabled-whenSignalingDisabled(35) ubr load balancing cannot be enabled when signaling is disabled virtualInterface-notSupported(36) virtual interface support only allowed on APS type of cards card-doesNotSupport-UPC(37) only some cardTypes support UPC atmUni-SvcVpiVci-RangeCheck-Failure(38) Do range check provided atmSignaling is enabled vciMinSvc <= vciMaxSvc and vpiMinSvc <= vpiMaxSvc atmUni-SigVpiVci-Within-Svc-Range(39) atmUni{Vpi,Vci}Sig should not be within svc range atmUni-Ilmi-Svc-Sig-VpiVci-Clash(40) if IlmiProtocol status and atmUniSignaling are both enabled then the Ilmi Vpi/Vci should not fall in the Svc range and should not be equal to signaling vpi/vci virtualUNI-VpiNotAvailable(41) vpi is not available for the virtual UNI virtualUNI-InvalidVUNIId(42) vitural UNI Index is invalid intfNotSupported-with-ds1LineType-d4(43) if dsx1LineType is DSX1_D4 channel, interface type can't be atmIma intfNotSupported-with-ds1LineCoding-ami(44) if dsx1LineCoding is DSX1_AMI channel interface type can't be atmIma onlyCEsupported-with-msBitStuffing-enabled(45) if msBitStuffing is enabled only interface type circuit emulation is supported vISuppConnTrafficShapingMutuallyExclusive(46) The VI support flag and Traffic Shaping flag are mutually exclusive tS16onPortNotCAS(47) must have cas on port for channel to have cas trunk line interface channelizationDisabled(48) should have channelization enabled to have cas trunk line

primaryDS1InterfaceNotConfigured(49) primary DS1 interface is not configured primaryTMCChanNotConfigured(50) primary timeslot management channel is not configured primaryTMCIntfAlreadyConfiguredInAnotherIg(51) primary timeslot management channel interface is already configured in another interface group primaryTMCIntfCantBeChanged(52) primary timeslot management channel interfance can't be changed

primaryEOCChanNotConfigured(53) primary embeded operation channel is not configured primaryEOCIntfAlreadyConfiguredInAnotherIg(54) primary embeded operation channel interface is already configured in another interface group primaryTMC-EOCIntfShouldBeSame(55) primary timeslot management channel and embeded operation channel interfaces should be the same primaryEOCIntfCantBeChanged(56) primary embeded operation channel inteface can't be changed primaryTMC-BackupTMCIntfCantBeSame(57) primary and backup timeslot management channel interfaces can't be the same

backupDS1InterfaceNotConfigured(58) backup DS1 interface is not configured backupTMCChanNotConfigured(59) backup timeslot management channel is not configured backupTMCIntfAlreadyConfiguredInAnotherIg(60) backup timeslot management channel interface is already configured in another interface group backupTMCIntfCantBeChanged(61) backup timeslot management channel interfance can't be changed

primaryEOC-BackupEOCIntfCantBeSame(62) primary and backup embeded operation channel interfaces can't be the same backupEOCChanNotConfigured(63) backup embeded operation channel is not configured backupEOCIntfAlreadyConfiguredInAnotherIg(64) backup embeded operation channel interface is already configured in another interface group backupTMC-EOCIntfShouldBeSame(65) backup timeslot management channel and embeded operation channel interfaces should be the same backupEOCIntfCantBeChanged(66) backup embeded operation channel inteface can't be changed

newBWBelowCurrentAllocated(67) new bandwidth is below the current allocated bandwidth newBWBelowCurrentAllocated-SvcsBeingDeleted(68) new bandwidth is below the current allocated bandwidth svc is being deleted newBWBelowCurrentAllocated-DeletePvcs(69) new bandwidth is below the current allocated bandwidth delete pvc newBWAboveCurrentAllocated(70) new bandwidth is above the current allocated bandwidth primaryInactive-or-SecondaryActive-In-IntfProtTable(71) an interface can't be deleted if it is in interface protection group which is primary/inactive or secondry/active onlyCEsupported-with-msLOSDetection-enabled(72) if msLOSDetection is enabled, only interface type circuit emulation is supported nonMuxNotAllowed-with-FaxRelay(73) DSP2 cards: if channelMode is CFG_DSP2_FAX_RELAY, aalMode can't be D_dsp2AalMode_aal2_non_multiplexed, invalid-DSPmode-and-AALmode-combination(74) DSP2 cards: such DSP mode and AAL mode combination is not allowed noBandwidth-For-SignalingConns(75) no bandwidth for signal connections