TPLINK-BANDWIDTH-MIB :: tpStormControlULRateMode

MIB Reference — IPNetwork Monitor · Updated October 06, 2026

All MIBs › TPLINK-BANDWIDTH-MIB › tpStormControlULRateMode

tpStormControlULRateMode

Module: TPLINK-BANDWIDTH-MIB

OID (symbolic): TPLINK-BANDWIDTH-MIB::tpStormControlULRateMode

OID (numeric): 1.3.6.1.4.1.11863.6.23.1.2.2.1.4

Node type: OBJECT-TYPE

Type: INTEGER

Access: read-write

Description: UL-Frame rate mode configuration. Configure kbps & ratio with the 'tpStormControlEnablePPS' setting to disable. Configure pps with the 'tpStormControlEnablePPS' setting to enable.

What is tpStormControlULRateMode?

This read-write value selects the unit used for the port's UL-frame (unknown unicast/unlisted-address) storm-control threshold: kbps(0), ratio(1), or pps(2), following the same rule that kbps/ratio(1) require tpStormControlEnablePPS disabled while pps(2) requires it enabled. An admin sets this to control how flooded unknown-unicast traffic on the port is measured before applying the actual limit in tpStormControlULRate. For example, choosing pps(2) lets the admin cap UL-frame flooding by packet rate rather than bandwidth.

Examples

Walk all instances (SNMPv2c):

snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11863.6.23.1.2.2.1.4
snmpwalk -v2c -c public <target> TPLINK-BANDWIDTH-MIB::tpStormControlULRateMode

Get a specific instance (index 1):

snmpget -v2c -c public <target> 1.3.6.1.4.1.11863.6.23.1.2.2.1.4.1
snmpget -v2c -c public <target> TPLINK-BANDWIDTH-MIB::tpStormControlULRateMode.1

Set instance 1 (SNMPv2c):

snmpset -v2c -c private <target> 1.3.6.1.4.1.11863.6.23.1.2.2.1.4.1 i <value>

Start monitoring TP-Link managed switch (per-port ingress/egress rate-limit config status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the TPLINK-BANDWIDTH-MIB::tpStormControlULRateMode OID value, configure state conditions and alerts, and monitor any TP-Link managed switch (per-port ingress/egress rate-limit config status) from a single console.

OID Breakdown

Upper-level ancestors (8 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.11863tplinkTPLINK-MIB
1.3.6.1.4.1.11863.6tplinkMgmtTPLINK-MIB
Numeric OIDNameModule
1.3.6.1.4.1.11863.6.23tplinkBandWidthMIBTPLINK-BANDWIDTH-MIB
1.3.6.1.4.1.11863.6.23.1tplinkBandWidthMIBObjectsTPLINK-BANDWIDTH-MIB
1.3.6.1.4.1.11863.6.23.1.2tpStormControlTPLINK-BANDWIDTH-MIB
1.3.6.1.4.1.11863.6.23.1.2.2tpStormControlModeTableTPLINK-BANDWIDTH-MIB
1.3.6.1.4.1.11863.6.23.1.2.2.1tpStormControlModeEntryTPLINK-BANDWIDTH-MIB
1.3.6.1.4.1.11863.6.23.1.2.2.1.4tpStormControlULRateModeTPLINK-BANDWIDTH-MIB