All MIBs › MITEL-IPLOGICAL-MIB
Organization: MITEL Corporation
Last Updated: 2003-03-24
Category: IP Addressing
Description:
Manages MITEL logical IP interface configuration and addressing parameters.
Imported Objects
From RFC1213-MIB
| ifIndex |
From SNMPv2-SMI
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| RowStatus |
What Is MITEL-IPLOGICAL-MIB?
MITEL-IPLOGICAL-MIB is a Mitel proprietary MIB, part of the mitelProprietary/mitelPropIpNetworking tree, that models logical IP interface and router configuration on Mitel IP telephony and networking equipment. It exposes IP networking configuration objects such as mitelIpNetRouter and mitelRouterIpGroup, describing how logical IP interfaces are grouped and addressed rather than raw traffic counters. Monitoring this MIB supports checking the software-configured state of the router's IP interface logic — confirming that addressing and routing group settings are correctly applied — which indirectly reflects whether the voice gateway's IP transport layer is healthy. It presumes underlying interface conventions similar to standard IF-MIB/IP-MIB indexing for the physical interfaces it configures. It is typically deployed on Mitel IP-PBX or voice gateway platforms where administrators need to manage logical IP routing for call-control and media traffic, typically by loading the MITEL-IPLOGICAL-MIB into a MIB Browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MITEL-IPLOGICAL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
What Can Be Monitored
- logical IP router configuration
- IP networking group assignment
- interface addressing state
Supported Devices
- Mitel IP-PBX / voice gateway platforms
Monitoring Examples
Polling mitelRouterIpGroup under mitelIpNetRouter lets an administrator confirm the logical IP router grouping configured on a Mitel voice gateway; a group setting that doesn't match the intended deployment topology would indicate a misconfiguration likely to disrupt call-control signaling or media routing.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mitel | 1.3.6.1.4.1.1027 | |||
| mitelProprietary | 1.3.6.1.4.1.1027.4 | |||
| mitelPropIpNetworking | 1.3.6.1.4.1.1027.4.8 | |||
| mitelIpNetRouter | 1.3.6.1.4.1.1027.4.8.1 | |||
| mitelRouterIpGroup | 1.3.6.1.4.1.1027.4.8.1.1 | |||
| mitelIpGrpLogicalGroup | 1.3.6.1.4.1.1027.4.8.1.1.5 | The MITEL IP MIB module. | ||
| mitelIpLogGrpLogicalTable | 1.3.6.1.4.1.1027.4.8.1.1.5.1 | not-accessible | A table containing information about logical IP LAN destinations. | |
| mitelIpLogGrpLogicalEntry | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1 | not-accessible | Each entry of this table contains information about a specific logical interface to a local area network. Each logical LAN can support routing or bridging functions, these are considered virtual interfaces. | |
| IP mitelIpLogAdvertisementAddress | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.1 | IpAddress | read-write | The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.255.255. (The all-systems address is preferred wherever possible, i.e., on any link where all listening hosts support IP multicast.) Default Value is 224.0.0.1 |
| INT mitelIpLogMaxAdvertisementInterval | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.2 | INTEGER | read-write | The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. |
| INT mitelIpLogMinAdvertisementInterval | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.3 | INTEGER | read-write | The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no greater than grIpLMaxAdvertisementInterval. |
| INT mitelIpLogAdvertisementLifetime | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.4 | INTEGER | read-write | The value to be placed in the Lifetime field of Router Advertisements sent from the interface, in seconds. Must be no less than grIpLMaxAdvertisementInterval. |
| INT mitelIpLogPerformRouterDiscovery | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.5 | INTEGER | read-write | A flag indicating whether or not the host is to perform ICMP router discovery on the interface. |
| IP mitelIpLogSolicitationAddress | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.6 | IpAddress | read-write | The IP destination address to be used for sending Router Solicitations from the interface. The only permissible values are the all-routers multicast address, 224.0.0.2, or the limited-broadcast address, 255.255.255.255. (The all-routers address is preferred wherever possible, i.e., on any link where all advertising routers support IP multicast.) Default 224.0.0.2 |
| ROW mitelIpLogStatus | 1.3.6.1.4.1.1027.4.8.1.1.5.1.1.7 | RowStatus | read-create | The current status of this entry. |
RFC description
IP logical interface configuration for MITEL routers, managing virtual LAN interfaces and routing/bridging functions.
Start monitoring Mitel IP-PBX/voice gateway platforms with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.