-- Teldat, S.A. -- Parque Tecnolgico de Madrid -- 28760, Tres Cantos (Madrid) -- Tlf: +34-918076565 -- Fax: +34-918076521 -- e-mail: id@teldat.com -- MIB privada de Teldat -- MIB de monitorizacin de DLSw. -- Historial: -- 07/02/14 M.A. Pastor XH 3523. Errors with HP Openview 9.20 -- 1.6 23/05/11 J. Roman Se implementa cambio de prioridad por -- porcentaje de conexiones activas -- 1.5 05/10/10 J. Roman XI 846. Prioridad dinamica y temporizador -- inactividad -- 1.4 08/07/09 I. Mu�oz Revisin de todas las MIB para evitar -- M.A. Pastor warnings y errores de compilacin -- 1.3 07/11/08 P. Nogueira Se corrigen intervalos y acceso a variables -- 1.2 30/10/08 J. Roman Se implementa capabilites MAC y NetBIOS List -- 1.1 16/11/06 J. Roman Se implementa modo pasivo -- 1.0 01/07/04 J. Molina Fichero procedente del fichero DLSw-MIB.mib -- 05-10-01 N. Villase�or Traduccin a ingl�s -- 01-12-00 M.A. Pastor Modificaciones para que pueda ser -- compilada utilizando compiladores -- distintos del de Teldat -- 11-07-00 M.A. Pastor -- J. Alvarez Implementacion inicial -------------------------------------------------------------------------- TELDAT-MON-PROTOCOL-DLSw-MIB DEFINITIONS ::= BEGIN -- Tipos importados IMPORTS IpAddress, Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB telProdNpMonProtocols FROM TELDAT-SW-STRUCTURE-MIB; telProdNpMonProtDLSw OBJECT IDENTIFIER ::= { telProdNpMonProtocols 7 } -- Grupo telProdNpMonProtDLSw telProdNpMonProtDLSwGlobalGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 1 } -- Grupo que engloba parametros generales. telProdNpMonProtDLSwGloParamGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSwGlobalGroup 1 } telProdNpMonProtDLSwGloParEnabled OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "DLSw protocol status, active (1) or inactive (2)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwGloParamGroup 1 } telProdNpMonProtDLSwGloParLLC2SendDisc OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-write STATUS mandatory DESCRIPTION "It represents the router prevention status to finish a LLC2 connection from the TCP connection loss. Possible values: active (1) or inactive (2)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwGloParamGroup 2 } telProdNpMonProtDLSwGloParAutoTCP OBJECT-TYPE SYNTAX INTEGER { passive(3), on-demand(2), always(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable the TCP stations automatic recovery when a session is interrupted, and when the router is being initialized. Possible values: active (1), it means to always connect; inactive (2), it means to connect when it is needed or on demand; passive (3), it means to no try connect." DEFVAL { 1 } ::={ telProdNpMonProtDLSwGloParamGroup 3 } telProdNpMonProtDLSwGloParSRBSegNum OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "SRB Segment that identifies to DLSw in the RIF." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGloParamGroup 4 } telProdNpMonProtDLSwGloParMapCacheSize OBJECT-TYPE SYNTAX INTEGER (4..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Cache size of association between MAC and IP addresses, to reduce exploration traffic." DEFVAL { 128 } ::={ telProdNpMonProtDLSwGloParamGroup 5 } telProdNpMonProtDLSwGloParMaxDLSwSessions OBJECT-TYPE SYNTAX INTEGER (1..60000) ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of DLSw sessions that router is able to support." DEFVAL { 1000 } ::={ telProdNpMonProtDLSwGloParamGroup 6 } telProdNpMonProtDLSwGloParPromisc OBJECT-TYPE SYNTAX INTEGER { disabled(2), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable Promiscuous mode. This mode permits accept connection form any neighbor. Possible values: enabled (1), it means mode enabled; disabled (2), it means mode disabled." DEFVAL { 2 } ::={ telProdNpMonProtDLSwGloParamGroup 7 } --Subgrupo del global que informa sobre la memoria. telProdNpMonProtDLSwGloMemoryGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSwGlobalGroup 2 } telProdNpMonProtDLSwGloMemDLSwGloAllot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of memory that DLSw has allowed using. The minimum value ir 26624. If a set try to fix this variable to a less value, it will take its minimum value (26624)." DEFVAL { 141312 } ::={ telProdNpMonProtDLSwGloMemoryGroup 1 } telProdNpMonProtDLSwGloMemLLCSessAllot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of memory that DLSw has allowed using in each LLC session. It must be zero or a positive integer." DEFVAL { 8192 } ::={ telProdNpMonProtDLSwGloMemoryGroup 2 } telProdNpMonProtDLSwGloMemSDLCSessAllot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of memory that DLSw has allowed using in each SDLC/QLLC session. It must be zero or a positive integer." DEFVAL { 4096 } ::={ telProdNpMonProtDLSwGloMemoryGroup 3 } telProdNpMonProtDLSwGloMemNetBIOSUIFraAllot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Number of bytes that router assigns as buffer for NetBIOS UI frames. It must be zero or a positive integer." DEFVAL { 40960 } ::={ telProdNpMonProtDLSwGloMemoryGroup 4 } --Subgrupo del global que informa sobre los temporizadores. telProdNpMonProtDLSwGloTimersGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSwGlobalGroup 3 } telProdNpMonProtDLSwGloTimDatabaseAge OBJECT-TYPE SYNTAX INTEGER (1..10000) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of time that database entries stay active." DEFVAL { 1200 } ::={ telProdNpMonProtDLSwGloTimersGroup 1 } telProdNpMonProtDLSwGloTimMaxICanReach OBJECT-TYPE SYNTAX INTEGER (1..1000) ACCESS read-write STATUS mandatory DESCRIPTION "Wait time for an answer to a CanYouReach before giving up." DEFVAL { 20 } ::={ telProdNpMonProtDLSwGloTimersGroup 2 } telProdNpMonProtDLSwGloTimLLCTestResp OBJECT-TYPE SYNTAX INTEGER (1..1000) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of time (in seconds) that router waits for a LLC test answer before relaying a LLC test frame." DEFVAL { 15 } ::={ telProdNpMonProtDLSwGloTimersGroup 3 } telProdNpMonProtDLSwGloTimSDLCTestResp OBJECT-TYPE SYNTAX INTEGER (1..1000) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of time (in seconds) that router waits for a SDLC test answer before relaying a SDLC test frame." DEFVAL { 15 } ::={ telProdNpMonProtDLSwGloTimersGroup 4 } telProdNpMonProtDLSwGloTimJoinGroupInterv OBJECT-TYPE SYNTAX INTEGER (1..60000) ACCESS read-write STATUS mandatory DESCRIPTION "Time (in seconds) between DLSw group advertisements transmission." DEFVAL { 900 } ::={ telProdNpMonProtDLSwGloTimersGroup 5 } telProdNpMonProtDLSwGloTimNeighPriority OBJECT-TYPE SYNTAX INTEGER (10..50) ACCESS read-write STATUS mandatory DESCRIPTION "Wait time (in decimas of second) during the exploration before selecting a neighbor." DEFVAL { 20 } ::={ telProdNpMonProtDLSwGloTimersGroup 6 } --Tabla que contiene par�metros relacionados con la Cache. telProdNpMonProtDLSwCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwCacheEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It lists DLSw MAC addresses cache entries. This cache contains a database with the most recent conversions of IP neighbors to MAC addresses." ::={ telProdNpMonProtDLSw 2 } telProdNpMonProtDLSwCacheEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwCacheEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It provides the MAC address, the life time (in seconds) within cache, the neighbor IP address and the greater size of frame, in addition to the index, that is the order number of the entry in the table." INDEX { telProdNpMonProtDLSwCacheIndex } ::={ telProdNpMonProtDLSwCacheTable 1 } TelProdNpMonProtDLSwCacheEntry ::= SEQUENCE { telProdNpMonProtDLSwCacheIndex INTEGER, telProdNpMonProtDLSwCacheMACAddress DisplayString, telProdNpMonProtDLSwCacheSecsToLive INTEGER, telProdNpMonProtDLSwCacheIpAddress IpAddress, telProdNpMonProtDLSwCacheLargestFra INTEGER } telProdNpMonProtDLSwCacheIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Entry order number. It is the table index." ::={ telProdNpMonProtDLSwCacheEntry 1 } telProdNpMonProtDLSwCacheMACAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "MAC Address." ::={ telProdNpMonProtDLSwCacheEntry 2 } telProdNpMonProtDLSwCacheSecsToLive OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "LIfe time (in seconds) within cache." ::={ telProdNpMonProtDLSwCacheEntry 3 } telProdNpMonProtDLSwCacheIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Neighbor IP address." ::={ telProdNpMonProtDLSwCacheEntry 4 } telProdNpMonProtDLSwCacheLargestFra OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Frame of greater size." ::={ telProdNpMonProtDLSwCacheEntry 5 } --Grupo que informa sobre el reparto de memoria. telProdNpMonProtDLSwMemoryGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 3 } --Subgrupo de par�metros globales sobre el uso de memoria. telProdNpMonProtDLSwMemGlobalGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSwMemoryGroup 1 } telProdNpMonProtDLSwMemGloTotBytesReq OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total number of requested bytes." DEFVAL { 141312 } ::={ telProdNpMonProtDLSwMemGlobalGroup 1 } telProdNpMonProtDLSwMemGloRxPoolGranted OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes assigned to reception global pool." ::={ telProdNpMonProtDLSwMemGlobalGroup 2 } telProdNpMonProtDLSwMemGloRxBytesUsed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes received at present." ::={ telProdNpMonProtDLSwMemGlobalGroup 3 } telProdNpMonProtDLSwMemGloTxPoolGranted OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes assigned to transmission global pool." ::={ telProdNpMonProtDLSwMemGlobalGroup 4 } telProdNpMonProtDLSwMemGloTxBytesUsed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes transmitted at present." ::={ telProdNpMonProtDLSwMemGlobalGroup 5 } telProdNpMonProtDLSwMemGloNetBIOSTotPool OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes reserved for NetBIOS UI frames pool. If NetBIOS is disabled, it will be zero by default." DEFVAL { 0 } ::={ telProdNpMonProtDLSwMemGlobalGroup 6 } telProdNpMonProtDLSwMemGloNetBIOSBytesUsed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes of the Netbios UI frames pool in use at present. If NetBIOS is disabled, it will be zero by default." DEFVAL { 0 } ::={ telProdNpMonProtDLSwMemGlobalGroup 7 } --Subgrupo de memoria para las sesiones (es una tabla). telProdNpMonProtDLSwMemSessTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwMemSessEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It lists all the existing DLSw sessions and the amount of memory used by each one." ::={ telProdNpMonProtDLSwMemoryGroup 2 } telProdNpMonProtDLSwMemSessEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwMemSessEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of the index with that the table is crossed over, that is the position of the entry in it, the session identifier, MAC and SAP source, MAC and SAP end, assigned initial amount, amount of free memory at the present moment, congestion status and total number of frames glued in sdlcim or sdlc to be transmitted by a specific circuit." INDEX { telProdNpMonProtDLSwMemSessIndex } ::={ telProdNpMonProtDLSwMemSessTable 1 } TelProdNpMonProtDLSwMemSessEntry ::= SEQUENCE{ telProdNpMonProtDLSwMemSessIndex INTEGER, telProdNpMonProtDLSwMemSessId INTEGER, telProdNpMonProtDLSwMemSessSourMAC DisplayString, telProdNpMonProtDLSwMemSessSourSAP INTEGER, telProdNpMonProtDLSwMemSessDestMAC DisplayString, telProdNpMonProtDLSwMemSessDestSAP INTEGER, telProdNpMonProtDLSwMemSessInitialAlloc INTEGER, telProdNpMonProtDLSwMemSessCurrFree INTEGER, telProdNpMonProtDLSwMemSessCongState INTEGER, telProdNpMonProtDLSwMemSessDLCTxQueu Counter } telProdNpMonProtDLSwMemSessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Order Number of the entry (corresponding to a session) in the table. It is the table index." ::={ telProdNpMonProtDLSwMemSessEntry 1 } telProdNpMonProtDLSwMemSessId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Session identifier." ::={ telProdNpMonProtDLSwMemSessEntry 2 } telProdNpMonProtDLSwMemSessSourMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Local MAC address. If session is SDLC or QLLC, its value will be 'SDLC' or 'QLLC' respectively." ::={ telProdNpMonProtDLSwMemSessEntry 3 } telProdNpMonProtDLSwMemSessSourSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Local SAP number." ::={ telProdNpMonProtDLSwMemSessEntry 4 } telProdNpMonProtDLSwMemSessDestMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC address." ::={ telProdNpMonProtDLSwMemSessEntry 5 } telProdNpMonProtDLSwMemSessDestSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC number." ::={ telProdNpMonProtDLSwMemSessEntry 6 } telProdNpMonProtDLSwMemSessInitialAlloc OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Initial amount of assigned memory. If it were not assigned, the value of this variable will be 0." ::={ telProdNpMonProtDLSwMemSessEntry 7 } telProdNpMonProtDLSwMemSessCurrFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Amount of free memory at the moment. If it were not assigned initially, the value of this variable will be 0." ::={ telProdNpMonProtDLSwMemSessEntry 8 } telProdNpMonProtDLSwMemSessCongState OBJECT-TYPE SYNTAX INTEGER { ses-gbl(4), global(3), session(2), ready(1), none(0) } ACCESS read-only STATUS mandatory DESCRIPTION "Session current status. Possible values are: ready(1), session(2), global(3) and ses-gbl(4). If memory were not assigned initially, the value of this variable will be 0 (none)." ::={ telProdNpMonProtDLSwMemSessEntry 9 } telProdNpMonProtDLSwMemSessDLCTxQueu OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames glued in sdlcim or sdlc to be transmitted by a specific circuit." ::={ telProdNpMonProtDLSwMemSessEntry 10 } --Grupo de par�metros relacionados con las sesiones activas. telProdNpMonProtDLSwSessionsGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 4 } --Tabla de las sesiones activas. Una entrada por sesin. telProdNpMonProtDLSwActSessTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwActSessEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It shows information of active DLS sessions at that moment, including MAC and SAP source, MAC and SAP end, session status, flags, remote IP address, and ID (identifier)." ::={ telProdNpMonProtDLSwSessionsGroup 1 } telProdNpMonProtDLSwActSessEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwActSessEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of the index with that the table is crossed over, that is the position of the entry in it, MAC and SAP source, MAC and SAP end, session current status, flags, remote IP address and session identifier." INDEX { telProdNpMonProtDLSwActSessIndex } ::={ telProdNpMonProtDLSwActSessTable 1 } TelProdNpMonProtDLSwActSessEntry ::= SEQUENCE { telProdNpMonProtDLSwActSessIndex INTEGER, telProdNpMonProtDLSwActSessLocalMAC DisplayString, telProdNpMonProtDLSwActSessLocalSAP INTEGER, telProdNpMonProtDLSwActSessRemMAC DisplayString, telProdNpMonProtDLSwActSessRemSAP INTEGER, telProdNpMonProtDLSwActSessState INTEGER, telProdNpMonProtDLSwActSessFlags DisplayString, telProdNpMonProtDLSwActSessRemIPAddr IpAddress, telProdNpMonProtDLSwActSessId INTEGER } telProdNpMonProtDLSwActSessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Order Number of the entry (corresponding to an active session) in the table. It is the table index." ::={ telProdNpMonProtDLSwActSessEntry 1 } telProdNpMonProtDLSwActSessLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Source MAC address of the session. If session is SDLC or QLLC, its value will be 'SDLC' or 'QLLC' respectively, instead of the MAC address." ::={ telProdNpMonProtDLSwActSessEntry 2 } telProdNpMonProtDLSwActSessLocalSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SAP opened in the source for this session." ::={ telProdNpMonProtDLSwActSessEntry 3 } telProdNpMonProtDLSwActSessRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC address of the session." ::={ telProdNpMonProtDLSwActSessEntry 4 } telProdNpMonProtDLSwActSessRemSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SAP opened in the end for this session." ::={ telProdNpMonProtDLSwActSessEntry 5 } telProdNpMonProtDLSwActSessState OBJECT-TYPE SYNTAX INTEGER { hlt-noak(14), circ-strt(13), wait-noack(12), rest-pend(11), halt-pending(10), disc-pend(9), connect-state(8), cont-pend(7), conn-pend(6), cir-rstrt(5), circ-est(4), circ-pend(3), rslv-pend(2), disconnected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Session current status: DISCONNECTED - Initial status hasn't a circuit or an established connection. RSLV_PEND - The DLSw target is waiting for a SSP_started indication after a SSP_start request. CIRC_PEND - The DLSw target is waiting for a SSP_REACHACK answer to a SSP_ICANREACH message. CIRC_EST - Circuit has been established end to end. CIR_RSTRT - The DLSw that originated reset is waiting for the reboot CONN_PEND - The DLSw source is waiting for a SSP_CONTACTED answer to a SSP_CONTACT message. CONT_PEND - The DLSw end is waiting for a SSP_CONTACTED confirmation to a SSP_CONTACT message. CONNECT_STATE - DISC_PEND - The DLSw that originated the disconnection is waiting for a SSP_HALTED answer to a SSP_HALT message. HALT_PENDING - The DLSw is waiting for a SSP_HALTED indication after a SSP_HALT request. RESTART_PEND - The remote DLSw is waiting for a SSP_HALTED indication after a SSP_HALT request. WAIT_NOACK - CIRC_STRT - HLT_NOACK - " ::={ telProdNpMonProtDLSwActSessEntry 6 } telProdNpMonProtDLSwActSessFlags OBJECT-TYPE SYNTAX DisplayString(SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "it is a string of six characters, so that each one that is present indicates one of the following situations: (A) PENDING MSG CONTACT (B) PENDING SAP RESOLUTION (C) AWAITED CONGESTION FINAL (D) OCCUPIED TCP (E) PENDING DISHABILITATION (F) INACTIVE CIRCUIT If the corresponding situation is not occurring, a blank space is introduced in the position where the character would have to appear." ::={ telProdNpMonProtDLSwActSessEntry 7 } telProdNpMonProtDLSwActSessRemIPAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "IP address of the remote DLS neighbor. If it is a local connection, or if the status is DISCONNECTED, the IP address will be 0.0.0.0." ::={ telProdNpMonProtDLSwActSessEntry 8 } telProdNpMonProtDLSwActSessId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number used for identifying the session." ::={ telProdNpMonProtDLSwActSessEntry 9 } --Tabla de par�metros de informacin detallada acerca de las sesiones --activas. Es un subgrupo del grupo de sesiones activas. telProdNpMonProtDLSwSessDetailTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwSessDetailEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "It shows detailed information about DLS session." ::={ telProdNpMonProtDLSwSessionsGroup 2 } telProdNpMonProtDLSwSessDetailEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwSessDetailEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, which is the order number of the entry in the table (each entry is an active session), the session identifier, the function of the router in the connection (if it is a sender or a receiver), transmitted and received XIDs from the remote DLSw neighbor, transmitted and received datagrams, transmitted and received information frames, information included in the RIF of the TEST LLC frame." INDEX { telProdNpMonProtDLSwSessDetIndex } ::={ telProdNpMonProtDLSwSessDetailTable 1 } TelProdNpMonProtDLSwSessDetailEntry ::= SEQUENCE { telProdNpMonProtDLSwSessDetIndex INTEGER, telProdNpMonProtDLSwSessDetId INTEGER, telProdNpMonProtDLSwSessDetPersonality INTEGER, telProdNpMonProtDLSwSessDetXIDsSent Counter, telProdNpMonProtDLSwSessDetXIDsRcvd Counter, telProdNpMonProtDLSwSessDetDatagSent Counter, telProdNpMonProtDLSwSessDetDatagRcvd Counter, telProdNpMonProtDLSwSessDetInfoFraSent Counter, telProdNpMonProtDLSwSessDetInfoFraRcvd Counter, telProdNpMonProtDLSwSessDetRIF DisplayString, telProdNpMonProtDLSwSessDetLocalCIDCorr INTEGER, telProdNpMonProtDLSwSessDetLocalCIDPortId INTEGER, telProdNpMonProtDLSwSessDetRemCIDCorr INTEGER, telProdNpMonProtDLSwSessDetRemCIDPortId INTEGER, telProdNpMonProtDLSwSessDetPriority INTEGER } telProdNpMonProtDLSwSessDetIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Order number of the entry (corresponding with an active session) in the table. It is the table index." ::={ telProdNpMonProtDLSwSessDetailEntry 1 } telProdNpMonProtDLSwSessDetId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number used for identifying the session." ::={ telProdNpMonProtDLSwSessDetailEntry 2 } telProdNpMonProtDLSwSessDetPersonality OBJECT-TYPE SYNTAX INTEGER { target(2), originator(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The ORIGINATOR (sender, 1) or TARGET (receiver, 2) of the connection." ::={ telProdNpMonProtDLSwSessDetailEntry 3 } telProdNpMonProtDLSwSessDetXIDsSent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "XIDs that this DLSw node has sent to its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 4 } telProdNpMonProtDLSwSessDetXIDsRcvd OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "XIDs that this DLSw node has received from its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 5 } telProdNpMonProtDLSwSessDetDatagSent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Datagrams that this DLSw node has sent to its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 6 } telProdNpMonProtDLSwSessDetDatagRcvd OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Datagrams that this DLSw node has received from its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 7 } telProdNpMonProtDLSwSessDetInfoFraSent OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Information frames that this DLSw node has sent to its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 8 } telProdNpMonProtDLSwSessDetInfoFraRcvd OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Information frames that this DLSw node has received from its remote DLSw neighbor." ::={ telProdNpMonProtDLSwSessDetailEntry 9 } telProdNpMonProtDLSwSessDetRIF OBJECT-TYPE SYNTAX DisplayString (SIZE(0..29)) ACCESS read-only STATUS mandatory DESCRIPTION "The information that is included in the RIF of the TEST LLC frame." ::={ telProdNpMonProtDLSwSessDetailEntry 10 } telProdNpMonProtDLSwSessDetLocalCIDCorr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Identifier in the local node for this session: Data link correlator." ::={ telProdNpMonProtDLSwSessDetailEntry 11 } telProdNpMonProtDLSwSessDetLocalCIDPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Identifier in the local node for this session: Data link port identifier." ::={ telProdNpMonProtDLSwSessDetailEntry 12 } telProdNpMonProtDLSwSessDetRemCIDCorr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Identifier in the remote node for this session: Data link correlator." ::={ telProdNpMonProtDLSwSessDetailEntry 13 } telProdNpMonProtDLSwSessDetRemCIDPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Identifier in the remote node for this session: Data link port identifier." ::={ telProdNpMonProtDLSwSessDetailEntry 14 } telProdNpMonProtDLSwSessDetPriority OBJECT-TYPE SYNTAX INTEGER { high(3), medium(2), low(1) } ACCESS read-only STATUS mandatory DESCRIPTION "DLSw neighbor priority." ::={ telProdNpMonProtDLSwSessDetailEntry 15 } --Tabla utilizada para poder eliminar sesiones. telProdNpMonProtDLSwSessDeleteTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwSessDeleteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is used to delete one active session of the two previous tables (the table of active sessions and the table of parameters of detailed information over the active sessions." ::={ telProdNpMonProtDLSwSessionsGroup 3 } telProdNpMonProtDLSwSessDeleteEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwSessDeleteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index that is used for crossing the table, and that is the order in which the entry corresponding to the session that is wished to delete in the two previous tables (table of active sessions and table of detailed parameters of the active sessions) appears, and of an erasure control variable, that indicates the result of the last erasure operation in reading, and in writing it is useful for initializing the operation when its value is 1 (erase)." INDEX { telProdNpMonProtDLSwSessDeleteIndex } ::={ telProdNpMonProtDLSwSessDeleteTable 1 } TelProdNpMonProtDLSwSessDeleteEntry ::= SEQUENCE { telProdNpMonProtDLSwSessDeleteIndex INTEGER, telProdNpMonProtDLSwSessDeleteDo INTEGER } telProdNpMonProtDLSwSessDeleteIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index, that will be the order number of entry to previous tables (active session table and detailed parameters of active sessions table), and therefore identifies the session to delete." ::={ telProdNpMonProtDLSwSessDeleteEntry 1 } telProdNpMonProtDLSwSessDeleteDo OBJECT-TYPE SYNTAX INTEGER { undefined(4), error(3), ok(2), delete(1) } ACCESS read-write STATUS mandatory DESCRIPTION "If the variable is set to 1, the session corresponding to the entry of which order number is indicated by the index, and the entries corresponding to it in the previous table disappear (active session table and detailed parameters of active sessions table). In a read operation (get) the value 2 will be get if the last delete attempt succeeded, 3 if an error ocurred and 4 if no sessions delete operation has been performed." ::={ telProdNpMonProtDLSwSessDeleteEntry 2 } --Grupo que informa sobre prioridades. telProdNpMonProtDLSwPriorityGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 5 } telProdNpMonProtDLSwPrioritySNA OBJECT-TYPE SYNTAX INTEGER { critical(4), high(3), medium(2), low(1), undefined(0) } ACCESS read-write STATUS mandatory DESCRIPTION "Priority for SNA DLSw sessions." ::={ telProdNpMonProtDLSwPriorityGroup 1 } telProdNpMonProtDLSwPriorityNetBIOS OBJECT-TYPE SYNTAX INTEGER { critical(4), high(3), medium(2), low(1), undefined(0) } ACCESS read-write STATUS mandatory DESCRIPTION "Priority for NetBIOS DLSw sessions." ::={ telProdNpMonProtDLSwPriorityGroup 2 } telProdNpMonProtDLSwPriorityCHML OBJECT-TYPE SYNTAX DisplayString (SIZE(0..4)) ACCESS read-write STATUS mandatory DESCRIPTION "Message allocation by priority. These 4 bytes indicate the maximum number of messages transmitted with a certain priority before transmitting messages with the following priority. Here they are shown as a 4 octect string, one per priority, and they correspond to C/H/M/L." ::={ telProdNpMonProtDLSwPriorityGroup 3 } telProdNpMonProtDLSwPriorityMaxFraSizNB OBJECT-TYPE SYNTAX INTEGER { very-high (4399), high (2052), medium (1470), low (516) } ACCESS read-write STATUS mandatory DESCRIPTION "Maximum NetBIOS frame size. Any value can be assigned to this variable through a set operation, but it will be rounded up to 516 (low) if it is under 516 or between 516 and 1470, to 1470 (medium) if it is between 1470 and 2502, and to 2502 (high) if it is between 2502 and 4399, or 4399 (too high) if it is bigger than this value." ::={ telProdNpMonProtDLSwPriorityGroup 4 } --Tabla para crear y eliminar SAPs. telProdNpMonProtDLSwSAPTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwSAPEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Enable the transmitting of data for the specified link SAP by the DLSw protocol. It should be executed on the router which resides on the session initiator side of the connection." ::={ telProdNpMonProtDLSw 6 } telProdNpMonProtDLSwSAPEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwSAPEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of two index, the interface number and the order number of the SAP inside the interface, and a variable to open and close SAP." INDEX { telProdNpMonProtDLSwSAPIfcIndex, telProdNpMonProtDLSwSAPNumIndex } ::={ telProdNpMonProtDLSwSAPTable 1 } TelProdNpMonProtDLSwSAPEntry ::= SEQUENCE { telProdNpMonProtDLSwSAPIfcIndex INTEGER, telProdNpMonProtDLSwSAPNumIndex INTEGER, telProdNpMonProtDLSwSAPCommand INTEGER } telProdNpMonProtDLSwSAPIfcIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number, from 1 to the maximum number of node interfaces (in console begin from 0 and here from 1). It is the first index." ::={ telProdNpMonProtDLSwSAPEntry 1 } telProdNpMonProtDLSwSAPNumIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SAP in decimal. Possible values: - values ranging between 0 and F4 (being even number), - 245 that will open 'SNA', ports 04, 08 and 0C, - 240 that will open 'NB' port, F0 for NetBIOS, - 244 that will open 'LNM' port F4." ::={ telProdNpMonProtDLSwSAPEntry 2 } telProdNpMonProtDLSwSAPCommand OBJECT-TYPE SYNTAX INTEGER { not-valid(4), close-sap(3), open-sap(2), valid(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Variable used to open or close SAPs. In a set operation the values 2 (open-sap) and 3 (close-sap) are accepted, and in a get operation the value 1 will be get if the open-SAP operation succeede, and 4 (invalid) if the open-SAP operation failed." ::={ telProdNpMonProtDLSwSAPEntry 3 } --Grupo de LLC2 telProdNpMonProtDLSwLLC2Group OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 7 } --Tabla que muestra informacin para todos los SAPs abiertos actualmente en --los interfaces entre los pares LLC2. telProdNpMonProtDLSwLLC2OpenTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwLLC2OpenEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays information for all currently open SAPs on interfaces between LLC2 peers." ::={ telProdNpMonProtDLSwLLC2Group 1 } telProdNpMonProtDLSwLLC2OpenEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwLLC2OpenEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the order number of the entry and two variables that display the interface and SAP respectively." INDEX { telProdNpMonProtDLSwLLC2OpenIndex } ::={ telProdNpMonProtDLSwLLC2OpenTable 1 } TelProdNpMonProtDLSwLLC2OpenEntry ::= SEQUENCE { telProdNpMonProtDLSwLLC2OpenIndex INTEGER, telProdNpMonProtDLSwLLC2OpenIfc INTEGER, telProdNpMonProtDLSwLLC2OpenSAP INTEGER } telProdNpMonProtDLSwLLC2OpenIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Order number of the entry inside the table. It is the table index." ::={ telProdNpMonProtDLSwLLC2OpenEntry 1 } telProdNpMonProtDLSwLLC2OpenIfc OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number." ::={ telProdNpMonProtDLSwLLC2OpenEntry 2 } telProdNpMonProtDLSwLLC2OpenSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Open SAP." ::={ telProdNpMonProtDLSwLLC2OpenEntry 3 } --Tabla con informacin de configuracin de los par�metros de SAPs. telProdNpMonProtDLSwLLC2SAPTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwLLC2SAPEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays configuration information on the Saps parameters. There is an entry per SAP of which parameters have been modified. As the table index is the order number of the entry inside the table, to add a new entry (change a SAP parameter not previously changed) a set operation is performed to the variable corresponding to the parameter value that is going to be changed, and with a residue larger than the number of existent entries in that moment. It only admits new entries if the SAP number is not already included, in the case of giving a new value to a SAP parameter, the position of the associated entry has to be found and acceded using the order number as index (as residue)." ::={ telProdNpMonProtDLSwLLC2Group 2 } telProdNpMonProtDLSwLLC2SAPEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwLLC2SAPEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the order number of the entry in the table, the SAP number, and the parameters t1 (Response timer), t2 (Received timer for Acknowledgment), ti (Inactive timer), n2 (Maximum number of retries value), n3 (Number of I frames received before sending Acknowledgment), tw (Transmission window), rw (Receive window), nw (Acknowledgments needed to increase Ww) and access priority (current LLC2 implementation does not use access priority)." INDEX { telProdNpMonProtDLSwLLC2SAPIndex } ::={ telProdNpMonProtDLSwLLC2SAPTable 1 } TelProdNpMonProtDLSwLLC2SAPEntry ::= SEQUENCE { telProdNpMonProtDLSwLLC2SAPIndex INTEGER, telProdNpMonProtDLSwLLC2SAPNumber INTEGER, telProdNpMonProtDLSwLLC2SAPT1 INTEGER, telProdNpMonProtDLSwLLC2SAPT2 INTEGER, telProdNpMonProtDLSwLLC2SAPTI INTEGER, telProdNpMonProtDLSwLLC2SAPN2 INTEGER, telProdNpMonProtDLSwLLC2SAPN3 INTEGER, telProdNpMonProtDLSwLLC2SAPTw INTEGER, telProdNpMonProtDLSwLLC2SAPRw INTEGER, telProdNpMonProtDLSwLLC2SAPNw INTEGER, telProdNpMonProtDLSwLLC2SAPAcc INTEGER } telProdNpMonProtDLSwLLC2SAPIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Order number of the entry in the table. It is the table index." ::={ telProdNpMonProtDLSwLLC2SAPEntry 1 } telProdNpMonProtDLSwLLC2SAPNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "SAP number." ::={ telProdNpMonProtDLSwLLC2SAPEntry 2 } telProdNpMonProtDLSwLLC2SAPT1 OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS mandatory DESCRIPTION "Reply timer. (In seconds). If the variable is set to 0, it returns to its default value (1)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 3 } telProdNpMonProtDLSwLLC2SAPT2 OBJECT-TYPE SYNTAX INTEGER (1..2560) ACCESS read-write STATUS mandatory DESCRIPTION "Receive Ack timer. (In 100millisec.). If the variable is set to 0, it returns to its default value (1)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 4 } telProdNpMonProtDLSwLLC2SAPTI OBJECT-TYPE SYNTAX INTEGER (1..256) ACCESS read-write STATUS mandatory DESCRIPTION "Inactivity Timer. (In seconds). If the variable is set to 0, it returns to its default value (30)." DEFVAL { 30 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 5 } telProdNpMonProtDLSwLLC2SAPN2 OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Retry value (retransmissions). If the variable is set to 0, the response is disabled. This is useful in SAP 0: users can disable retransmission of TEST and XID scanning." DEFVAL { 8 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 6 } telProdNpMonProtDLSwLLC2SAPN3 OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Number I-frames received before sending ACK. If the variable is set to 0, it returns to its default value (1)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 7 } telProdNpMonProtDLSwLLC2SAPTw OBJECT-TYPE SYNTAX INTEGER (1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Transmit Window. If the variable is set to 0, it returns to its default value (2)." DEFVAL { 2 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 8 } telProdNpMonProtDLSwLLC2SAPRw OBJECT-TYPE SYNTAX INTEGER (1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Receive Window . If the variable is set to 0, it returns to its default value (2)." DEFVAL { 2 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 9 } telProdNpMonProtDLSwLLC2SAPNw OBJECT-TYPE SYNTAX INTEGER (1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Acks needed to increment Ww. If the variable is set to 0, it returns to its default value (1)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 10 } telProdNpMonProtDLSwLLC2SAPAcc OBJECT-TYPE SYNTAX INTEGER (0..7) ACCESS read-only STATUS mandatory DESCRIPTION "Current LLC2 implementation does not use access priority. Default 0." DEFVAL { 0 } ::={ telProdNpMonProtDLSwLLC2SAPEntry 11 } --Tabla de informacin sobre las sesiones LLC2. telProdNpMonProtDLSwLLC2SessionsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwLLC2SessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays current information and parameters on all active LLC2 sessions." ::={ telProdNpMonProtDLSwLLC2Group 3 } telProdNpMonProtDLSwLLC2SessionsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwLLC2SessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the entry order number (corresponding to an active LLC2 session) in the table, SAP number, interface number, local and remote MAC addresses, current state of the LLC2 session in correspondence with the entry and information included in the RIF of TEST LLC frame." INDEX { telProdNpMonProtDLSwLLC2SessIndex } ::={ telProdNpMonProtDLSwLLC2SessionsTable 1 } TelProdNpMonProtDLSwLLC2SessionsEntry ::= SEQUENCE{ telProdNpMonProtDLSwLLC2SessIndex INTEGER, telProdNpMonProtDLSwLLC2SessSAP INTEGER, telProdNpMonProtDLSwLLC2SessInt INTEGER, telProdNpMonProtDLSwLLC2SessRemMAC DisplayString, telProdNpMonProtDLSwLLC2SessLocalMAC DisplayString, telProdNpMonProtDLSwLLC2SessState INTEGER, telProdNpMonProtDLSwLLC2SessFlag INTEGER, telProdNpMonProtDLSwLLC2SessRIF DisplayString } telProdNpMonProtDLSwLLC2SessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Entry order number (corresponding to an active LLC2 session in the table). It is the index." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 1 } telProdNpMonProtDLSwLLC2SessSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SAP number. If the field CCB (Connection Control Block) of the LLC Interface Module (LIM), that supplies the SAP number, is not initialized (NULL), the variable value will be 0." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 2 } telProdNpMonProtDLSwLLC2SessInt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number. If the field CCB (Connection Control Block) of the LLC Interface Module (LIM), that supplies the SAP number, is not initialized (NULL), the variable value will be 0." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 3 } telProdNpMonProtDLSwLLC2SessRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "The destination MAC address of the session." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 4 } telProdNpMonProtDLSwLLC2SessLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "The source MAC address of the session." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 5 } telProdNpMonProtDLSwLLC2SessState OBJECT-TYPE SYNTAX INTEGER { disconnect-pending(7), contacted(6), contact-pend(5), connected(4), resolve-pend(3), connect-pend(2), disconnected(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current state of the session. Possible values are: disconnected (1), connect-pend (2), resolve-pend (3), connected (4), contact-pend (5), disconnect-pending (6), contacted (7)." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 6 } telProdNpMonProtDLSwLLC2SessFlag OBJECT-TYPE SYNTAX INTEGER { sap-resolve-pending-start-by-xid-llcbusy-tcpbusy(15), sap-resolve-pending-start-by-xid-tcpbusy(14), sap-resolve-pending-start-by-xid-llcbusy(13), sap-resolve-pending-start-by-xid(12), sap-resolve-pending-llcbusy-tcpbusy(11), sap-resolve-pending-tcpbusy(10), sap-resolve-pending-llcbusy(9), sap-resolve-pending(8), start-by-xid-llcbusy-tcpbusy(7), start-by-xid-tcpbusy(6), start-by-xid-llcbusy(5), start-by-xid(4), llcbusy-tcpbusy(3), tcpbusy(2), llcbusy(1), nothing(0) } ACCESS read-only STATUS mandatory DESCRIPTION "One of the following values: NOTHING (0), LLCBUSY (1), TCPBUSY (2), LLCBUSY+TCPBUSY (3), START-BY-XID (4), START-BY-XID+LLCBUSY (5), START-BY-XID+TCPBUSY (6), START-BY-XID+LLCBUSY+TCPBUSY (7), SAP-RESOLVE-PENDING (8), SAP-RESOLVE-PENDING+LLCBUSY (9), SAP-RESOLVE-PENDING+TCPBUSY (10), SAP-RESOLVE-PENDING+LLCBUSY+TCPBUSY (11), SAP-RESOLVE-PENDING+START-BY-XID (12), SAP-RESOLVE-PENDING+START-BY-XID+LLCBUSY (13), SAP-RESOLVE-PENDING+START-BY-XID+TCPBUSY (14), SAP-RESOLVE-PENDING+START-BY-XID+LLCBUSY+TCPBUSY (15)." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 7 } telProdNpMonProtDLSwLLC2SessRIF OBJECT-TYPE SYNTAX DisplayString (SIZE(0..29)) ACCESS read-only STATUS mandatory DESCRIPTION "The information that is included in the RIF of the LLC TEST frame." ::={ telProdNpMonProtDLSwLLC2SessionsEntry 8 } --Grupo de par�metros que contienen informacin relativa a las estaciones --o enlaces SDLC definidos en DLSw. telProdNpMonProtDLSwSDLCGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 8 } --Tabla con los par�metros configurados para la Unidad F�sica (PU) conectada --por SDLC. telProdNpMonProtDLSwSDLCConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwSDLCConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays the parameters configured for the PUs (physical unit) connected by SDLC. Open new connections and allows to change table parameters if the concrete connection is disabled." ::={ telProdNpMonProtDLSwSDLCGroup 1 } telProdNpMonProtDLSwSDLCConfigEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwSDLCConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of two index: number of the interface configured as SDLC and the SDLC address, variable used to add and delete table entries, link state (active or inactive), device identifier or physical unit to which is connected, physical unit type, MAC address and SAPs local and remote addresses." INDEX { telProdNpMonProtDLSwSDLCConfNetIndex, telProdNpMonProtDLSwSDLCConfAddrIndex } ::={ telProdNpMonProtDLSwSDLCConfigTable 1 } TelProdNpMonProtDLSwSDLCConfigEntry ::= SEQUENCE { telProdNpMonProtDLSwSDLCConfNetIndex INTEGER, telProdNpMonProtDLSwSDLCConfAddrIndex INTEGER, telProdNpMonProtDLSwSDLCConfCommand INTEGER, telProdNpMonProtDLSwSDLCConfStatus INTEGER, telProdNpMonProtDLSwSDLCConfIdblk INTEGER, telProdNpMonProtDLSwSDLCConfIdnum INTEGER, telProdNpMonProtDLSwSDLCConfLocalSAP INTEGER, telProdNpMonProtDLSwSDLCConfLocalMAC DisplayString, telProdNpMonProtDLSwSDLCConfRemSAP INTEGER, telProdNpMonProtDLSwSDLCConfRemMAC DisplayString } telProdNpMonProtDLSwSDLCConfNetIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number, SDLC type. First index." ::={ telProdNpMonProtDLSwSDLCConfigEntry 1 } telProdNpMonProtDLSwSDLCConfAddrIndex OBJECT-TYPE SYNTAX INTEGER (1..254) ACCESS read-only STATUS mandatory DESCRIPTION "Address to use in the SDLC messages. This is a decimal value between 00 and FF. If 00 is programmed the session will use FF and learn the address from the remote SDLC station. Second index." ::={ telProdNpMonProtDLSwSDLCConfigEntry 2 } telProdNpMonProtDLSwSDLCConfCommand OBJECT-TYPE SYNTAX INTEGER { not-valid(4), delete(3), add(2), valid(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Variable used to open or delete SDLC sessions. In a set operation, possible values are 2 (open) and 3 (delete), and in a read operation (get) the value 1 will be get if the last operation succeeded, and 4 if an error ocurred." ::={ telProdNpMonProtDLSwSDLCConfigEntry 3 } telProdNpMonProtDLSwSDLCConfStatus OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Displays the session state." ::={ telProdNpMonProtDLSwSDLCConfigEntry 4 } telProdNpMonProtDLSwSDLCConfIdblk OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "It is a value under 4095 (0xfff) that identifies the device (PU) to which you are connecting. Normally you will use Idblk for PUs on switches lines (as opposed to leased lines). Therefore, this value should match this same parameter in the VTAM Switched Major Node that corresponds to this PU." ::={ telProdNpMonProtDLSwSDLCConfigEntry 5 } telProdNpMonProtDLSwSDLCConfIdnum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "It is a value under 1048575 (0xffffff) that identifies the specific device type (2.0) that you are connecting. Normally you will use Ibnum for PUs on switched lines (as opposed to leased lines). Therefore, this value should match this same parameter in the VTAM Switched Major Node that corresponds to this PU." ::={ telProdNpMonProtDLSwSDLCConfigEntry 6 } telProdNpMonProtDLSwSDLCConfLocalSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Local SAP number." ::={ telProdNpMonProtDLSwSDLCConfigEntry 7 } telProdNpMonProtDLSwSDLCConfLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-write STATUS mandatory DESCRIPTION "Local MAC Address." ::={ telProdNpMonProtDLSwSDLCConfigEntry 8 } telProdNpMonProtDLSwSDLCConfRemSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Remote SAP number." ::={ telProdNpMonProtDLSwSDLCConfigEntry 9 } telProdNpMonProtDLSwSDLCConfRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-write STATUS mandatory DESCRIPTION "Remote MAC Address." ::={ telProdNpMonProtDLSwSDLCConfigEntry 10 } --Tabla donde se encuentra la informacin acerca de todas las sesiones DLS --SDLC dentro del router. telProdNpMonProtDLSwSDLCSessionsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwSDLCSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays information about every DLS SDLC session inside the router." ::={ telProdNpMonProtDLSwSDLCGroup 2 } telProdNpMonProtDLSwSDLCSessionsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwSDLCSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the entry order number, the interface number (SDLC type), address to use the in SDLC messages, local and remote MAC addresses, local and remote SAPs, frames pending to be sent to SDLC and SDLC session state." INDEX { telProdNpMonProtDLSwSDLCSessIndex } ::={ telProdNpMonProtDLSwSDLCSessionsTable 1 } TelProdNpMonProtDLSwSDLCSessionsEntry ::= SEQUENCE { telProdNpMonProtDLSwSDLCSessIndex INTEGER, telProdNpMonProtDLSwSDLCSessIfc INTEGER, telProdNpMonProtDLSwSDLCSessAddr INTEGER, telProdNpMonProtDLSwSDLCSessLocalSAP INTEGER, telProdNpMonProtDLSwSDLCSessLocalMAC DisplayString, telProdNpMonProtDLSwSDLCSessRemSAP INTEGER, telProdNpMonProtDLSwSDLCSessRemMAC DisplayString, telProdNpMonProtDLSwSDLCSessOutQ Counter, telProdNpMonProtDLSwSDLCSessState INTEGER } telProdNpMonProtDLSwSDLCSessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index. Order number of the entry inside the table (corresponding to a session)." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 1 } telProdNpMonProtDLSwSDLCSessIfc OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number (SDLC type)." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 2 } telProdNpMonProtDLSwSDLCSessAddr OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Address to use in the SDLC messages. Decimal value between 00 and FF. If 00 is programmed, the session will use FF and learn the address from the remote SDLC station." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 3 } telProdNpMonProtDLSwSDLCSessLocalSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Local SAP number." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 4 } telProdNpMonProtDLSwSDLCSessLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Local MAC address." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 5 } telProdNpMonProtDLSwSDLCSessRemSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Remote SAP number." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 6 } telProdNpMonProtDLSwSDLCSessRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC address." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 7 } telProdNpMonProtDLSwSDLCSessOutQ OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Frames pending to be sent to SDLC." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 8 } telProdNpMonProtDLSwSDLCSessState OBJECT-TYPE SYNTAX INTEGER { sec-ctac-pend(17), sec-nxid-pend(16), sec-idle(15), conn-pend2(14), conn-pend(13), cs-pend(12), conn-req-pend(11), xid-pend(10), disc-pend(9), xid-0-pend(8), null-xid-pend(7), contacted(6), connected(5), resolve-pend(4), test-pend(3), disconnected(2), net-down(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Session state." ::={ telProdNpMonProtDLSwSDLCSessionsEntry 9 } --Grupo de par�metros con informacin relativa a las estaciones QLLC --definidas en el DLSw. telProdNpMonProtDLSwQLLCGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 9 } --Tabla con los par�metros configurados para la unidad f�sica (PU) --conectada por QLLC telProdNpMonProtDLSwQLLCConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwQLLCConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays the parameters configured for the PUs connected by QLLC. It opens new connections and allows changing connection parameters whenever it were disabled." ::={ telProdNpMonProtDLSwQLLCGroup 1 } telProdNpMonProtDLSwQLLCConfigEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwQLLCConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the order number of the entry, a variable to add and delete new entries or QLLC links, local NUA, remote NUA, MAC address, local SAP, remote SAP, alternative X.25 Network number to which the X.25 call is made should the call to the remote NUA fail, address to use in the QLLC messages, and a variable that indicates the QLLC station's availability status (active or inactive)." INDEX { telProdNpMonProtDLSwQLLCConfQLLCIndex } ::={ telProdNpMonProtDLSwQLLCConfigTable 1 } TelProdNpMonProtDLSwQLLCConfigEntry ::= SEQUENCE { telProdNpMonProtDLSwQLLCConfQLLCIndex INTEGER, telProdNpMonProtDLSwQLLCConfCommand INTEGER, telProdNpMonProtDLSwQLLCConfRemNUA DisplayString, telProdNpMonProtDLSwQLLCConfLocalNUA DisplayString, telProdNpMonProtDLSwQLLCConfLocalSAP INTEGER, telProdNpMonProtDLSwQLLCConfLocalMAC DisplayString, telProdNpMonProtDLSwQLLCConfRemSAP INTEGER, telProdNpMonProtDLSwQLLCConfRemMAC DisplayString, telProdNpMonProtDLSwQLLCConfRemAltNUA DisplayString, telProdNpMonProtDLSwQLLCConfQLLCAddr INTEGER, telProdNpMonProtDLSwQLLCConfStatus INTEGER } telProdNpMonProtDLSwQLLCConfQLLCIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index. Indicates the order number of the entry." ::={ telProdNpMonProtDLSwQLLCConfigEntry 1 } telProdNpMonProtDLSwQLLCConfCommand OBJECT-TYPE SYNTAX INTEGER { not-valid(4), delete(3), add(2), valid(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Variable used to open and delete QLLC sessions. When writting it admits the value 2 (add) and 3 (delete), and when reading it will be got the value 1 (valid) if the last operation succeeded, and 4 (invalid) if failed." ::={ telProdNpMonProtDLSwQLLCConfigEntry 2 } telProdNpMonProtDLSwQLLCConfRemNUA OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-write STATUS mandatory DESCRIPTION "X.25 network number identifying the remote QLLC station. This number discriminates the incoming calls. Should there be any wildcards ('X') outgoing calls are not permitted from this station." ::={ telProdNpMonProtDLSwQLLCConfigEntry 3 } telProdNpMonProtDLSwQLLCConfLocalNUA OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-write STATUS mandatory DESCRIPTION "X.25 network number identifying the local station. This number discriminates the outgoing calls. In outgoing calls this is used as NUA calling. Should there be any wildcards ('X') this is not used in outgoing calls." ::={ telProdNpMonProtDLSwQLLCConfigEntry 4 } telProdNpMonProtDLSwQLLCConfLocalSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Local SAP number." ::={ telProdNpMonProtDLSwQLLCConfigEntry 5 } telProdNpMonProtDLSwQLLCConfLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-write STATUS mandatory DESCRIPTION "Local MAC address." ::={ telProdNpMonProtDLSwQLLCConfigEntry 6 } telProdNpMonProtDLSwQLLCConfRemSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Remote SAP number." ::={ telProdNpMonProtDLSwQLLCConfigEntry 7 } telProdNpMonProtDLSwQLLCConfRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-write STATUS mandatory DESCRIPTION "Remote MAC address." ::={ telProdNpMonProtDLSwQLLCConfigEntry 8 } telProdNpMonProtDLSwQLLCConfRemAltNUA OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-write STATUS mandatory DESCRIPTION "Alternative X.25 Network number to which the X.25 call is made should the call to the remote NUA fail. This is optional and may not exist in which case this facility is not enabled." ::={ telProdNpMonProtDLSwQLLCConfigEntry 9 } telProdNpMonProtDLSwQLLCConfQLLCAddr OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Address to use in the QLLC messages. This is a decimal value between 00 and FF. If 00 is programmed the session will use FF and learn the address from the remote QLLC station. First index." ::={ telProdNpMonProtDLSwQLLCConfigEntry 10 } telProdNpMonProtDLSwQLLCConfStatus OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the QLLC station's availability status (Active 1) or inactivity (Inactive 2) in order to carry out connections." ::={ telProdNpMonProtDLSwQLLCConfigEntry 11 } --Tabla donde se encuentra la informacin acerca de todas las sesiones QLLC --DLSw dentro del router. telProdNpMonProtDLSwQLLCSessionsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwQLLCSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays information about all QLLC DLSw session in the router. " ::={ telProdNpMonProtDLSwQLLCGroup 2 } telProdNpMonProtDLSwQLLCSessionsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwQLLCSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that is the order number of the entry in the table, remote NUA, local MAC address and local SAP, QLLC address, frames pending to be sent to QLLC, QLLC session state, local NUA, remote SAP and remote MAC address." INDEX { telProdNpMonProtDLSwQLLCSessIndex } ::={ telProdNpMonProtDLSwQLLCSessionsTable 1 } TelProdNpMonProtDLSwQLLCSessionsEntry ::= SEQUENCE { telProdNpMonProtDLSwQLLCSessIndex INTEGER, telProdNpMonProtDLSwQLLCSessRemNUA DisplayString, telProdNpMonProtDLSwQLLCSessLocalSAP INTEGER, telProdNpMonProtDLSwQLLCSessLocalMAC DisplayString, telProdNpMonProtDLSwQLLCSessAddr INTEGER, telProdNpMonProtDLSwQLLCSessOutQ Counter, telProdNpMonProtDLSwQLLCSessQLLCState INTEGER, telProdNpMonProtDLSwQLLCSessLocalNUA DisplayString, telProdNpMonProtDLSwQLLCSessRemSAP INTEGER, telProdNpMonProtDLSwQLLCSessRemMAC DisplayString } telProdNpMonProtDLSwQLLCSessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: order number of the entry." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 1 } telProdNpMonProtDLSwQLLCSessRemNUA OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "X.25 network number identifying the remote QLLC station. This number discriminates the incoming calls. Should there be any wildcards ('X') outgoing calls are not permitted from this station." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 2 } telProdNpMonProtDLSwQLLCSessLocalSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Local SAP number." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 3 } telProdNpMonProtDLSwQLLCSessLocalMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Local MAC address." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 4 } telProdNpMonProtDLSwQLLCSessAddr OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Address to use in the QLLC messages. Decimal value between 00 and FF. If 00 is programmed, the session will use FF and learn the address from the remote QLLC station." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 5 } telProdNpMonProtDLSwQLLCSessOutQ OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Frames pending to be sent to QLLC." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 6 } telProdNpMonProtDLSwQLLCSessQLLCState OBJECT-TYPE SYNTAX INTEGER { sec-ctac-pend(19), sec-nxid-pend(18), sec-idle(17), conn-pend2(16), conn-pend(15), cs-pend(14), conn-req-pend(13), xid-pend(12), disc-pend(11), xid-0-pend(10), null-xid-pend(9), contacted(8), connected(7), resolve-pend(6), test-pend(5), disconnected(4), qllc-cnx-pend(3), qllc-cnx-off(2), net-down(1) } ACCESS read-only STATUS mandatory DESCRIPTION "QLLC session state. The possible states are: NET_DOWN : QLLC interface down. QLLC_CNX_OFF : X.25 connection disconnected. QLLC_CNX_PEND : X.25 connection pending. DISCONNECTED : QLLC session disconnected. TEST_PEND : RESOLVE_PEND : Pending on finding remote station. CONNECTED : QLLC session open. CONTACTED : QLLC session active. NULL_XID_PEND : Waiting for empty XID. XID_0_PEND : DISC_PEND : Waiting for QLLC session disconnection. XID_PEND : Session waiting for XID response. CONN_REQ_PEND : QLLC session pending connection. CS_PEND : CONN_PEND : CONN_PEND2 : SEC_IDLE : SEC_NXID_PEND : SEC_CTAC_PEND :" ::={ telProdNpMonProtDLSwQLLCSessionsEntry 7 } telProdNpMonProtDLSwQLLCSessLocalNUA OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "X.25 network number identifying the local station. This number discriminates the outgoing calls. In outgoing calls this is used as NUA calling. Should there be any wildcards ('X') this is not used in outgoing calls." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 8 } telProdNpMonProtDLSwQLLCSessRemSAP OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Remote SAP number." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 9 } telProdNpMonProtDLSwQLLCSessRemMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote MAC address." ::={ telProdNpMonProtDLSwQLLCSessionsEntry 10 } --Grupo de TCP telProdNpMonProtDLSwTCPGroup OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 10 } --Tabla que recoge la informacin recibida de un router asociado, en el --mensaje de intercambio de aptitudes. telProdNpMonProtDLSwTCPCapabTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPCapabEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays the information received from an associated router, in the capabilities exchange message." ::={ telProdNpMonProtDLSwTCPGroup 1 } telProdNpMonProtDLSwTCPCapabEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPCapabEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, DLSw neighbor IP Address, vendor ID, vendor product version, pacing window, supported SAPs, MAC List exclusive and NetBIOS Name List exclusive." INDEX { telProdNpMonProtDLSwTCPCapIndex } ::={ telProdNpMonProtDLSwTCPCapabTable 1 } TelProdNpMonProtDLSwTCPCapabEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPCapIndex INTEGER, telProdNpMonProtDLSwTCPCapIpAddr IpAddress, telProdNpMonProtDLSwTCPCapVendorID DisplayString, telProdNpMonProtDLSwTCPCapVenProVers DisplayString, telProdNpMonProtDLSwTCPCapIniPacWind INTEGER, telProdNpMonProtDLSwTCPCapSuppSAPs DisplayString, telProdNpMonProtDLSwTCPCapMacExcl INTEGER, telProdNpMonProtDLSwTCPCapNbExcl INTEGER } telProdNpMonProtDLSwTCPCapIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: order number of the table entry." ::={ telProdNpMonProtDLSwTCPCapabEntry 1 } telProdNpMonProtDLSwTCPCapIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "DLSw neighbor IP Address " ::={ telProdNpMonProtDLSwTCPCapabEntry 2 } telProdNpMonProtDLSwTCPCapVendorID OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Vendor ID." ::={ telProdNpMonProtDLSwTCPCapabEntry 3 } telProdNpMonProtDLSwTCPCapVenProVers OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Vendor product version." ::={ telProdNpMonProtDLSwTCPCapabEntry 4 } telProdNpMonProtDLSwTCPCapIniPacWind OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Initial pacing window." ::={ telProdNpMonProtDLSwTCPCapabEntry 5 } telProdNpMonProtDLSwTCPCapSuppSAPs OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Supported SAPs." ::={ telProdNpMonProtDLSwTCPCapabEntry 6 } telProdNpMonProtDLSwTCPCapMacExcl OBJECT-TYPE SYNTAX INTEGER { no-exclusive(0), exclusive(1) } ACCESS read-only STATUS mandatory DESCRIPTION "MAC Address List exclusivity." ::={ telProdNpMonProtDLSwTCPCapabEntry 7 } telProdNpMonProtDLSwTCPCapNbExcl OBJECT-TYPE SYNTAX INTEGER { no-exclusive(0), exclusive(1) } ACCESS read-only STATUS mandatory DESCRIPTION "NetBIOS Name List exclusivity." ::={ telProdNpMonProtDLSwTCPCapabEntry 8 } --Tabla que contiene la informacin referida a todas las sesiones TCP --configuradas. telProdNpMonProtDLSwTCPConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays the information in all the configured TCP sessions." ::={ telProdNpMonProtDLSwTCPGroup 2 } telProdNpMonProtDLSwTCPConfigEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, a variable to add or delete entries, neighbor IP Address, Transmit Buffer size, Receive Buffer size, maximum segment size, variable to activate or not the DLSw neighbor possibility to send keepalive messages, another that indicates the neighbor�s priority, and neighbor connection mode." INDEX { telProdNpMonProtDLSwTCPConfIndex } ::={ telProdNpMonProtDLSwTCPConfigTable 1 } TelProdNpMonProtDLSwTCPConfigEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPConfIndex INTEGER, telProdNpMonProtDLSwTCPConfCommand INTEGER, telProdNpMonProtDLSwTCPConfIpAddr IpAddress, telProdNpMonProtDLSwTCPConfTxBufsize INTEGER, telProdNpMonProtDLSwTCPConfRxBufsize INTEGER, telProdNpMonProtDLSwTCPConfMaxSegsize INTEGER, telProdNpMonProtDLSwTCPConfKeepAlive INTEGER, telProdNpMonProtDLSwTCPConfPriority INTEGER, telProdNpMonProtDLSwTCPConfCnxMode INTEGER, telProdNpMonProtDLSwTCPConfInacTime INTEGER, telProdNpMonProtDLSwTCPConfLowPriMax INTEGER, telProdNpMonProtDLSwTCPConfLowPriMin INTEGER, telProdNpMonProtDLSwTCPConfLowPriRetries INTEGER, telProdNpMonProtDLSwTCPConfLowPriTimeout INTEGER, telProdNpMonProtDLSwTCPConfLowPriMaxPercent INTEGER, telProdNpMonProtDLSwTCPConfLowPriMinPercent INTEGER } telProdNpMonProtDLSwTCPConfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: entry order number." ::={ telProdNpMonProtDLSwTCPConfigEntry 1 } telProdNpMonProtDLSwTCPConfCommand OBJECT-TYPE SYNTAX INTEGER { not-valid(4), delete(3), add(2), valid(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Variable used to add and delete new TCP neighbor entries. When writting it admits the value 2 (add) and 3 (delete), and when reading it will be got the value 1 (valid) if the last operation succeeded, and 4 (invalid) if failed." ::={ telProdNpMonProtDLSwTCPConfigEntry 2 } telProdNpMonProtDLSwTCPConfIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Neighbor IP Address." ::={ telProdNpMonProtDLSwTCPConfigEntry 3 } telProdNpMonProtDLSwTCPConfTxBufsize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Transmit Buffer size. Possible values are within the interval (1024..65536), and the value will be 0 when it is a local connection-conversion." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwTCPConfigEntry 4 } telProdNpMonProtDLSwTCPConfRxBufsize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Receive Buffer size. Possible values are within the interval (1024..65536), and the value will be 0 when it is a local connection-conversion." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwTCPConfigEntry 5 } telProdNpMonProtDLSwTCPConfMaxSegsize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum segment size. Possible values are within the interval (1024..65536), and the value will be 0 when it is a local connection-conversion." DEFVAL { 1024 } ::={ telProdNpMonProtDLSwTCPConfigEntry 6 } telProdNpMonProtDLSwTCPConfKeepAlive OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1), no-sense(0) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates if we want the DLSw neighbor to send keepalive messages. Option default active. Possible values are: active (1), inactive (2) and no-sense (0), that indicates it is a local connection-conversion." DEFVAL { 1 } ::={ telProdNpMonProtDLSwTCPConfigEntry 7 } telProdNpMonProtDLSwTCPConfPriority OBJECT-TYPE SYNTAX INTEGER { high(3), medium(2), low(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor priority through the values high (3), medium (2), low (1). DLSw protocol uses this parameter to determine which DLSw neighbor to choose when several can reach the destination station." DEFVAL { 2 } ::={ telProdNpMonProtDLSwTCPConfigEntry 8 } telProdNpMonProtDLSwTCPConfCnxMode OBJECT-TYPE SYNTAX INTEGER { promiscuous(5), passive(4), always(3), on-demand(2), default(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor connection mode through the values promiscuous (5), passive (4), always (3), on demand (2), default (1). DLSw protocol uses this parameter to determine when connections must be connected to neigbors. Default value uses configured global value." DEFVAL { 1 } ::={ telProdNpMonProtDLSwTCPConfigEntry 9 } telProdNpMonProtDLSwTCPConfInacTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor inactivity time without active circuits in order to disconnect the link. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 10 } telProdNpMonProtDLSwTCPConfLowPriMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of active circuits. When the number of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 11 } telProdNpMonProtDLSwTCPConfLowPriMin OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum number of active circuits. When the number of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 12 } telProdNpMonProtDLSwTCPConfLowPriRetries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of connection retries. When the number of unsuccessfull circuit connections exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 13 } telProdNpMonProtDLSwTCPConfLowPriTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying time to recover configured priority when the actual priority was fired by excess of number of unsuccessfull circuit connections. (0 = Priority will not changed)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 14 } telProdNpMonProtDLSwTCPConfLowPriMaxPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum percentage of active circuits. When the percentage of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 15 } telProdNpMonProtDLSwTCPConfLowPriMinPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum percentage of active circuits. When the percentage of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPConfigEntry 16 } --Tabla que contiene la versin, el n�mero de sesiones DLSw activas que --utilizan esta sesin TCP, y el n�mero de sesiones que alguna vez han --utilizado esta sesin. telProdNpMonProtDLSwTCPSessionsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays version, number of DLSw active sessions used by this TCP session, and the number of sessions that al least once have used this session." ::={ telProdNpMonProtDLSwTCPGroup 3 } telProdNpMonProtDLSwTCPSessionsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPSessionsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, the group identifier, IP address of the TCP session, current state of the TCP session, version, number of DLSw sessions currently activated in the TCP session and the number of DLSw sessions used in this TCP session." INDEX { telProdNpMonProtDLSwTCPSessIndex } ::={ telProdNpMonProtDLSwTCPSessionsTable 1 } TelProdNpMonProtDLSwTCPSessionsEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPSessIndex INTEGER, telProdNpMonProtDLSwTCPSessRole INTEGER, telProdNpMonProtDLSwTCPSessGroup INTEGER, telProdNpMonProtDLSwTCPSessIpAddr IpAddress, telProdNpMonProtDLSwTCPSessConnState INTEGER, telProdNpMonProtDLSwTCPSessVersion DisplayString, telProdNpMonProtDLSwTCPSessNumActSess INTEGER, telProdNpMonProtDLSwTCPSessNumCreates INTEGER } telProdNpMonProtDLSwTCPSessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: order number of the table entry." ::={ telProdNpMonProtDLSwTCPSessionsEntry 1 } telProdNpMonProtDLSwTCPSessRole OBJECT-TYPE SYNTAX INTEGER { peer-to-peer(3), server(2), client(1), undefined(0) } ACCESS read-only STATUS mandatory DESCRIPTION "Group type: 1 for client, 2 for server and 3 for peer-to peer. A server forms a TCP connection with a client." ::={ telProdNpMonProtDLSwTCPSessionsEntry 2 } telProdNpMonProtDLSwTCPSessGroup OBJECT-TYPE SYNTAX INTEGER (0..69) ACCESS read-only STATUS mandatory DESCRIPTION "Group identifier. If it is 0 the router does not belong to any group." ::={ telProdNpMonProtDLSwTCPSessionsEntry 3 } telProdNpMonProtDLSwTCPSessIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "IP address of the TCP session." ::={ telProdNpMonProtDLSwTCPSessionsEntry 4 } telProdNpMonProtDLSwTCPSessConnState OBJECT-TYPE SYNTAX INTEGER { reconnect-wait(9), closing(8), established(7), capex-pending(6), wr-est-rd-pend(5), pending-r-w(4), rd-est-wr-pend(3), down(2), capex-failed(1) } ACCESS read-only STATUS mandatory DESCRIPTION "Current state of the TCP session." ::={ telProdNpMonProtDLSwTCPSessionsEntry 5 } telProdNpMonProtDLSwTCPSessVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Version name." ::={ telProdNpMonProtDLSwTCPSessionsEntry 6 } telProdNpMonProtDLSwTCPSessNumActSess OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of DLSw sessions currently active in the TCP session." ::={ telProdNpMonProtDLSwTCPSessionsEntry 7 } telProdNpMonProtDLSwTCPSessNumCreates OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of DLSw sessions in this TCP session." ::={ telProdNpMonProtDLSwTCPSessionsEntry 8 } --Tabla que recoge los estad�sticos del uso de sesiones TCP telProdNpMonProtDLSwTCPStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays the use statistics of the TCP sessions." ::={ telProdNpMonProtDLSwTCPGroup 4 } telProdNpMonProtDLSwTCPStatsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, DLSw neighbor IP Address, number of data messages, number of data bytes, number of Control Messages, number of Can You Reach Messages, number of I Can Reach Messages, number of Name Query messages and Name Recognized transmitted and received." INDEX { telProdNpMonProtDLSwTCPStIndex } ::={ telProdNpMonProtDLSwTCPStatsTable 1 } TelProdNpMonProtDLSwTCPStatsEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPStIndex INTEGER, telProdNpMonProtDLSwTCPStIpAddr IpAddress, telProdNpMonProtDLSwTCPStDataMessTx Counter, telProdNpMonProtDLSwTCPStDataMessRx Counter, telProdNpMonProtDLSwTCPStDataBytesTx Counter, telProdNpMonProtDLSwTCPStDataBytesRx Counter, telProdNpMonProtDLSwTCPStContMessTx Counter, telProdNpMonProtDLSwTCPStContMessRx Counter, telProdNpMonProtDLSwTCPStCanYouReachTx Counter, telProdNpMonProtDLSwTCPStCanYouReachRx Counter, telProdNpMonProtDLSwTCPStICanReachTx Counter, telProdNpMonProtDLSwTCPStICanReachRx Counter, telProdNpMonProtDLSwTCPStNameQueryTx Counter, telProdNpMonProtDLSwTCPStNameQueryRx Counter, telProdNpMonProtDLSwTCPStNameRecognTx Counter, telProdNpMonProtDLSwTCPStNameRecognRx Counter } telProdNpMonProtDLSwTCPStIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: entry order number, corresponding to a TCP session (of which statistics are displayed)." ::={ telProdNpMonProtDLSwTCPStatsEntry 1 } telProdNpMonProtDLSwTCPStIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "DLSw neighbor IP Address." ::={ telProdNpMonProtDLSwTCPStatsEntry 2 } telProdNpMonProtDLSwTCPStDataMessTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Data Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 3 } telProdNpMonProtDLSwTCPStDataMessRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Data Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 4 } telProdNpMonProtDLSwTCPStDataBytesTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Data Bytes transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 5 } telProdNpMonProtDLSwTCPStDataBytesRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Data Bytes received." ::={ telProdNpMonProtDLSwTCPStatsEntry 6 } telProdNpMonProtDLSwTCPStContMessTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Control Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 7 } telProdNpMonProtDLSwTCPStContMessRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Control Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 8 } telProdNpMonProtDLSwTCPStCanYouReachTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "CanYouReach Explorer Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 9 } telProdNpMonProtDLSwTCPStCanYouReachRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "CanYouReach Explorer Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 10 } telProdNpMonProtDLSwTCPStICanReachTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "ICanReach Explorer Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 11 } telProdNpMonProtDLSwTCPStICanReachRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "ICanReach Explorer Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 12 } telProdNpMonProtDLSwTCPStNameQueryTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "NameQuery Explorer Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 13 } telProdNpMonProtDLSwTCPStNameQueryRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "NameQuery Explorer Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 14 } telProdNpMonProtDLSwTCPStNameRecognTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "NameRecognized Explorer Messages transmitted." ::={ telProdNpMonProtDLSwTCPStatsEntry 15 } telProdNpMonProtDLSwTCPStNameRecognRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "NameRecognized Explorer Messages received." ::={ telProdNpMonProtDLSwTCPStatsEntry 16 } -- Grupo que engloba los parametros por defecto para modo Promiscuo. telProdNpMonProtDLSwTCPPromisGroup OBJECT IDENTIFIER ::={ telProdNpMonProtDLSwTCPGroup 5 } telProdNpMonProtDLSwTCPPromisTxBufsize OBJECT-TYPE SYNTAX INTEGER(1024..65536) ACCESS read-write STATUS mandatory DESCRIPTION "Transmit Buffer size. Possible values are within the interval (1024..65536)." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwTCPPromisGroup 1 } telProdNpMonProtDLSwTCPPromisRxBufsize OBJECT-TYPE SYNTAX INTEGER(1024..65536) ACCESS read-write STATUS mandatory DESCRIPTION "Receive Buffer size. Possible values are within the interval (1024..65536)." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwTCPPromisGroup 2 } telProdNpMonProtDLSwTCPPromisMaxSegsize OBJECT-TYPE SYNTAX INTEGER(64..16384) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum segment size. Possible values are within the interval (64..16384)." DEFVAL { 1024 } ::={ telProdNpMonProtDLSwTCPPromisGroup 3 } telProdNpMonProtDLSwTCPPromisKeepAlive OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates if we want the DLSw neighbor to send keepalive messages. Option default active. Possible values are: active (1) and inactive (2)." DEFVAL { 1 } ::={ telProdNpMonProtDLSwTCPPromisGroup 4 } telProdNpMonProtDLSwTCPPromisPriority OBJECT-TYPE SYNTAX INTEGER { high(3), medium(2), low(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor priority through the values high (3), medium (2), low (1). DLSw protocol uses this parameter to determine which DLSw neighbor to choose when several can reach the destination station." DEFVAL { 2 } ::={ telProdNpMonProtDLSwTCPPromisGroup 5 } telProdNpMonProtDLSwTCPPromisInacTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor inactivity time without active circuits in order to disconnect the link. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 6 } telProdNpMonProtDLSwTCPPromisLowPriMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of active circuits. When the number of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 7 } telProdNpMonProtDLSwTCPPromisLowPriMin OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum number of active circuits. When the number of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 8 } telProdNpMonProtDLSwTCPPromisLowPriRetries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of connection retries. When the number of unsuccessfull circuit connections exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 9 } telProdNpMonProtDLSwTCPPromisLowPriTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying time to recover configured priority when the actual priority was fired by excess of number of unsuccessfull circuit connections. (0 = Priority will not changed)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 10 } telProdNpMonProtDLSwTCPPromisLowPriMaxPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum percentage of active circuits. When the percentage of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 11 } telProdNpMonProtDLSwTCPPromisLowPriMinPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum percentage of active circuits. When the percentage of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwTCPPromisGroup 12 } -- Tabla que engloba las MAC Address List anunciadas. telProdNpMonProtDLSwTCPCapMacListTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPCapMacListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays MAC Address Lists received form neighbors." ::={ telProdNpMonProtDLSwTCPGroup 6 } telProdNpMonProtDLSwTCPCapMacListEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPCapMacListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, DLSw neighbor IP Address, MAC address value and MAC address mask received from neighbors." INDEX { telProdNpMonProtDLSwTCPCapMacListIndex } ::={ telProdNpMonProtDLSwTCPCapMacListTable 1 } TelProdNpMonProtDLSwTCPCapMacListEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPCapMacListIndex INTEGER, telProdNpMonProtDLSwTCPCapMacListIpAddr IpAddress, telProdNpMonProtDLSwTCPCapMacListMAC DisplayString, telProdNpMonProtDLSwTCPCapMacListMask DisplayString } telProdNpMonProtDLSwTCPCapMacListIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: entry order number, corresponding to a TCP session and entry order in list." ::={ telProdNpMonProtDLSwTCPCapMacListEntry 1 } telProdNpMonProtDLSwTCPCapMacListIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "DLSw neighbor IP Address." ::={ telProdNpMonProtDLSwTCPCapMacListEntry 2 } telProdNpMonProtDLSwTCPCapMacListMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "MAC Address value." ::={ telProdNpMonProtDLSwTCPCapMacListEntry 3 } telProdNpMonProtDLSwTCPCapMacListMask OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) ACCESS read-only STATUS mandatory DESCRIPTION "MAC Address mask." ::={ telProdNpMonProtDLSwTCPCapMacListEntry 4 } -- Tabla que engloba las NetBIOS Name List anunciadas. telProdNpMonProtDLSwTCPCapNbListTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwTCPCapNbListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Displays NetBIOS Name Lists received form neighbors." ::={ telProdNpMonProtDLSwTCPGroup 7 } telProdNpMonProtDLSwTCPCapNbListEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwTCPCapNbListEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, DLSw neighbor IP Address, NetBIOS Name Type and NetBIOS Name received from neighbors." INDEX { telProdNpMonProtDLSwTCPCapNbListIndex } ::={ telProdNpMonProtDLSwTCPCapNbListTable 1 } TelProdNpMonProtDLSwTCPCapNbListEntry ::= SEQUENCE { telProdNpMonProtDLSwTCPCapNbListIndex INTEGER, telProdNpMonProtDLSwTCPCapNbListIpAddr IpAddress, telProdNpMonProtDLSwTCPCapNbListType INTEGER, telProdNpMonProtDLSwTCPCapNbListName DisplayString } telProdNpMonProtDLSwTCPCapNbListIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Table index: entry order number, corresponding to a TCP session and entry order in list." ::={ telProdNpMonProtDLSwTCPCapNbListEntry 1 } telProdNpMonProtDLSwTCPCapNbListIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "DLSw neighbor IP Address." ::={ telProdNpMonProtDLSwTCPCapNbListEntry 2 } telProdNpMonProtDLSwTCPCapNbListType OBJECT-TYPE SYNTAX INTEGER { individual(0), group(1) } ACCESS read-only STATUS mandatory DESCRIPTION "NetBIOS Name Type. (Individual/Group)" ::={ telProdNpMonProtDLSwTCPCapNbListEntry 3 } telProdNpMonProtDLSwTCPCapNbListName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "NetBIOS Name." ::={ telProdNpMonProtDLSwTCPCapNbListEntry 4 } --Tabla que contiene los par�metros referentes a todos los grupos --configurados a los que el router pertenezca. telProdNpMonProtDLSwGroupsTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpMonProtDLSwGroupsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Group configuration." ::={ telProdNpMonProtDLSw 11 } telProdNpMonProtDLSwGroupsEntry OBJECT-TYPE SYNTAX TelProdNpMonProtDLSwGroupsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of an index, that will be the order number of the table entry, a variable to join a router to a specified group or remove the router from it, group number, group type (server, client or peer to peer), transmit and receive buffer size, maximum size of the TCP segment, variable that shows whether the DLSw neighbor will send link keepalive messages or not, and another which specifies the neighbor priority." INDEX { telProdNpMonProtDLSwGroupsIndex } ::={ telProdNpMonProtDLSwGroupsTable 1 } TelProdNpMonProtDLSwGroupsEntry ::= SEQUENCE { telProdNpMonProtDLSwGroupsIndex INTEGER, telProdNpMonProtDLSwGroupsCommand INTEGER, telProdNpMonProtDLSwGroupsRole INTEGER, telProdNpMonProtDLSwGroupsTxBufsize INTEGER, telProdNpMonProtDLSwGroupsRxBufsize INTEGER, telProdNpMonProtDLSwGroupsMaxSegSize INTEGER, telProdNpMonProtDLSwGroupsKeepAlive INTEGER, telProdNpMonProtDLSwGroupsPriority INTEGER, telProdNpMonProtDLSwGroupsCnxMode INTEGER, telProdNpMonProtDLSwGroupsInacTime INTEGER, telProdNpMonProtDLSwGroupsLowPriMax INTEGER, telProdNpMonProtDLSwGroupsLowPriMin INTEGER, telProdNpMonProtDLSwGroupsLowPriRetries INTEGER, telProdNpMonProtDLSwGroupsLowPriTimeout INTEGER, telProdNpMonProtDLSwGroupsLowPriMaxPercent INTEGER, telProdNpMonProtDLSwGroupsLowPriMinPercent INTEGER } telProdNpMonProtDLSwGroupsIndex OBJECT-TYPE SYNTAX INTEGER (0..69) ACCESS read-only STATUS mandatory DESCRIPTION "Table index: group number." ::={ telProdNpMonProtDLSwGroupsEntry 1 } telProdNpMonProtDLSwGroupsCommand OBJECT-TYPE SYNTAX INTEGER{ error(4), leave-group(3), join-group(2), ok(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Use the JOIN-GROUP command to allow DLSw neighbors to find and to create TCP sessions with each other dynamically. This eliminates the need to define TCP neighbors with the ADD TCP command. In a get operation this variable can be 1 (ok) if the last JOIN-GROUP or LEAVE-GROUP operation succeeded and 4 (error) if failed. In a set operation admits 1 (join-group) and 3 (leave-group), that initiates the corresponding operations" ::={ telProdNpMonProtDLSwGroupsEntry 2 } telProdNpMonProtDLSwGroupsRole OBJECT-TYPE SYNTAX INTEGER { peer-to-peer(3), server(2), client(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of group that you want to join the router: 1 for client, 2 for server, and 3 for peer-to-peer. A server forms a TCP connection with a client." ::={ telProdNpMonProtDLSwGroupsEntry 3 } telProdNpMonProtDLSwGroupsTxBufsize OBJECT-TYPE SYNTAX INTEGER (1024..65536) ACCESS read-write STATUS mandatory DESCRIPTION "The size of the packet transmit buffer." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwGroupsEntry 4 } telProdNpMonProtDLSwGroupsRxBufsize OBJECT-TYPE SYNTAX INTEGER (1024..65536) ACCESS read-write STATUS mandatory DESCRIPTION "The size of the packet receive buffer." DEFVAL { 5120 } ::={ telProdNpMonProtDLSwGroupsEntry 5 } telProdNpMonProtDLSwGroupsMaxSegSize OBJECT-TYPE SYNTAX INTEGER (64..16384) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum size of the TCP segment." DEFVAL { 1024 } ::={ telProdNpMonProtDLSwGroupsEntry 6 } telProdNpMonProtDLSwGroupsKeepAlive OBJECT-TYPE SYNTAX INTEGER { inactive(2), active(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether you want the DLSw neighbor to send link keepalive messages." DEFVAL { 1 } ::={ telProdNpMonProtDLSwGroupsEntry 7 } telProdNpMonProtDLSwGroupsPriority OBJECT-TYPE SYNTAX INTEGER { high(3), medium(2), low(1), none(0) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the neighbor priority as high (3), medium (2) or low (1). It should never be none (0). DLSw uses this parameter to determine which DLSw neighbor to choose when multiple neighbors can reach a target station." DEFVAL { 2 } ::={ telProdNpMonProtDLSwGroupsEntry 8 } telProdNpMonProtDLSwGroupsCnxMode OBJECT-TYPE SYNTAX INTEGER { promiscuous(5), passive(4), always(3), on-demand(2), default(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor connection mode through the values promiscuous (5), passive (4), always (3), on demand (2), default (1). DLSw protocol uses this parameter to determine when connections must be connected to neigbors. Default value uses configured global value." DEFVAL { 1 } ::={ telProdNpMonProtDLSwGroupsEntry 9 } telProdNpMonProtDLSwGroupsInacTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying neighbor inactivity time without active circuits in order to disconnect the link. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 10 } telProdNpMonProtDLSwGroupsLowPriMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of active circuits. When the number of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 11 } telProdNpMonProtDLSwGroupsLowPriMin OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum number of active circuits. When the number of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 12 } telProdNpMonProtDLSwGroupsLowPriRetries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum number of connection retries. When the number of unsuccessfull circuit connections exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 13 } telProdNpMonProtDLSwGroupsLowPriTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying time to recover configured priority when the actual priority was fired by excess of number of unsuccessfull circuit connections. (0 = Priority will not changed)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 14 } telProdNpMonProtDLSwGroupsLowPriMaxPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying maximum percentage of active circuits. When the number of active circuits exceeds this parameter, the system will change the priority of this link to low value. (0 = Disable feature)." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 15 } telProdNpMonProtDLSwGroupsLowPriMinPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Allows specifying minimum percentage of active circuits. When the percentage of active circuits is lower than this parameter, the system will change the priority of this link to configured value." DEFVAL { 0 } ::={ telProdNpMonProtDLSwGroupsEntry 16 } --Grupo BAN telProdNpMonProtDLSwBAN OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 12 } --Grupo NetBIOS sobre DLSw telProdNpMonProtDLSwNetBIOS OBJECT IDENTIFIER ::= { telProdNpMonProtDLSw 13 } END