-- Teldat, S.A. -- Parque Tecnolgico de Madrid -- 28760, Tres Cantos (Madrid) -- Tlf: +34-918076565 -- Fax: +34-918076521 -- e-mail: id@teldat.com -- MIB privada de Teldat -- MIB de parmetros globales de configuracin. -- Historial: -- 07/02/14 M.A. Pastor XH 3523. Errors with HP Openview 9.20 -- 1.8 11-01-13 E. Amorena XH 2610. MIBs compilation. -- 1.7 08/07/09 I. Munoz Revisin de todas las MIB para evitar -- M.A. Pastor warnings y errores de compilacin -- 1.6 12/12/08 P. Nogueira Variables obsoletas, correciones -- 1.5 05/03/08 J. Herrero Aadidos estados operativos de interfaz -- 1.4 21/02/08 J. Herrero Corregida para compilacin con -- M.A. Pastor MG-Soft MIB Compiler -- 1.3 08/02/05 M.A. Pastor Aunque se introdujo el cabecero no se -- haban corregido realmente los valores -- del medio activo -- 1.2 29/11/04 M.A. Pastor Corregidos valores medio activo -- 1.1 09/07/04 J. Molina Reload<->Restart -- 1.0 01/07/04 J. Molina Fichero procedente de nucleox.mib -- Historial de nucleox.mib: -- 1.0 (beta) 18/07/97 Jose Picot Coca & Ignacio Salas Salmern -- Implementacion inicial -------------------------------------------------------------------------- TELDAT-CFG-CommonInfo-MIB DEFINITIONS ::= BEGIN -- Tipos importados IMPORTS TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB telProductsNpConfig FROM TELDAT-SW-STRUCTURE-MIB; -- ConfigControl telProdNpConfigControl OBJECT IDENTIFIER ::= { telProductsNpConfig 1 } telProdNpConfigControlBugsClear OBJECT-TYPE SYNTAX INTEGER{ nondeletebugs(0), deletebugs(1) } ACCESS not-accessible STATUS mandatory DESCRIPTION "In writing 1 resets all bugs stored in the system, in reading always 0." ::={ telProdNpConfigControl 1 } telProdNpConfigControlReload OBJECT-TYPE SYNTAX INTEGER{ set(1), last-set-ok(2), last-set-failed(3), indeterminated(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset of the device." ::={ telProdNpConfigControl 2 } telProdNpConfigControlRestart OBJECT-TYPE SYNTAX INTEGER{ set(1), last-set-ok(2), last-set-failed(3), indeterminated(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Restart of the device." ::={ telProdNpConfigControl 3 } telProdNpConfigControlSaveConfig OBJECT-TYPE SYNTAX INTEGER{ set(1), last-set-ok(2), last-set-failed(3), indeterminated(4), confirm-set(5) } ACCESS read-write STATUS mandatory DESCRIPTION "It saves the configuration parameters of the device." ::={ telProdNpConfigControl 4 } telProdNpConfigControlOKSet OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Number of processed and returned set by the SNMP agent. If a set to 1 (the only allowed value for set) is realized, the counter is reset to 0." ::={ telProdNpConfigControl 5 } telProdNpConfChkSum OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS obsolete DESCRIPTION "It establishes a backup of the SRAM to check the integrity of the data contained in it." ::={ telProdNpConfigControl 6 } telProdNpConfActDev OBJECT-TYPE SYNTAX INTEGER { smartcard-flash(1), smartcard(2), flash(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Active Device. Device used to read and write configuration files." ::={ telProdNpConfigControl 7 } telProdNpConfConfSavedDev OBJECT-TYPE SYNTAX INTEGER { smartcard(1), flash(2), smartcard-flash(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Device where the last configuration has been saved." ::={ telProdNpConfigControl 8 } -- ConfDataGlobal telProdNpConfDataGlobal OBJECT IDENTIFIER ::= { telProductsNpConfig 2 } telProdNpConfDataDescription OBJECT-TYPE SYNTAX DisplayString(SIZE(0..100)) ACCESS read-only STATUS mandatory DESCRIPTION "A description of the device which includes hardware type, networking software and operating system." ::={ telProdNpConfDataGlobal 1 } telProdNpConfDataObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "Object Identifier assigned to the device" ::={ telProdNpConfDataGlobal 2 } telProdNpConfDataName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Name assigned to the device (generally the one of TCP/IP)." ::={ telProdNpConfDataGlobal 3 } telProdNpConfDataContact OBJECT-TYPE SYNTAX DisplayString(SIZE(0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Contact person; along with other data, as the telephone number." ::={ telProdNpConfDataGlobal 4 } telProdNpConfDataLocation OBJECT-TYPE SYNTAX DisplayString(SIZE(0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Location; where the device is located physically." ::={ telProdNpConfDataGlobal 5 } telProdNpConfDataServices OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A coded number which indicates the layers for which this node performs services." ::={ telProdNpConfDataGlobal 6 } telProdNpConfDataUptime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Time in hundredths of a second from the last reboot of the device." ::={ telProdNpConfDataGlobal 7 } telProdNpConfDataInactTime OBJECT-TYPE SYNTAX INTEGER(1..600) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum time (in minutes) of inactivity of the telnet, after which session disconnection will take place." ::={ telProdNpConfDataGlobal 9 } -- La tabla BuffersRx -- La tabla de BuffersRx contiene la informacion del -- tamanyo del buffer de recepcion de cada uno de los -- interfaces del router. Solo de la parte router (los interfaces del -- 1 hasta el Router-Nodo excluido), no de la parte nodo. telProdNpConfDataBuffersRxTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpConfDataBuffersRxEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "BuffersRx list. The value of the interface determines the entry number." ::= { telProdNpConfDataGlobal 8 } telProdNpConfDataBuffersRxEntry OBJECT-TYPE SYNTAX TelProdNpConfDataBuffersRxEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "Each entry consists of the router interface number of the device and the size of the reception buffer." INDEX { telProdNpConfDataBuffersRxIndex } ::={ telProdNpConfDataBuffersRxTable 1 } TelProdNpConfDataBuffersRxEntry ::= SEQUENCE{ telProdNpConfDataBuffersRxIndex INTEGER, telProdNpConfDataBuffersRxValue INTEGER } telProdNpConfDataBuffersRxIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS obsolete DESCRIPTION "Interface number of the router part of the device. It is the table index, and its value is between 1 until Router-Node, this last one excluded." ::={ telProdNpConfDataBuffersRxEntry 1 } telProdNpConfDataBuffersRxValue OBJECT-TYPE SYNTAX INTEGER(5..255) ACCESS read-write STATUS obsolete DESCRIPTION "Size of the reception buffer. If the assigned value is less than 5 the default value will be 5, and if it is more than 255 the default value will be 255." DEFVAL{5} ::={ telProdNpConfDataBuffersRxEntry 2 } -- ConfInterfaceAsignation telProdNpConfInterfaceAsignation OBJECT IDENTIFIER ::= { telProductsNpConfig 6 } -- Esta rama de asignacion de interfaces tiene tres partes. -- La primera (solo de lectura, telProdNpInterfAsigListInitial) -- muestra la configuracion de los interfaces que tenia al ROUTER en -- la ultima reinicializacion o reseteo. La tabla asociada la indexa el -- n de interfaz. La segunda (telProdNpInterfAsig) permite la asignacion -- de un tipo de interfaz al conector deseado. La tabla asociada la indexa -- el numero de conector. -- La tercera (solo de lectura,telProdNpInterfAsigListModify) muestra la -- configuracion de los interfaces en el momento actual; -- teniendo en cuenta las modificaciones realizadas en -- la tabla telProdNpInterfAsigTable. La tabla asociada la indexa el n de -- interfaz. -- Grupo telProdNpInterfAsigListInitial telProdNpInterfAsigListInitial OBJECT IDENTIFIER ::= { telProdNpConfInterfaceAsignation 1 } -- Tabla telProdNpInterfAsigListInitialTable -- La tabla de configuracion inicial de interfaces -- (despues del ultimo reset o reinicializacion del ROUTER). -- La tabla de interfaces contiene el indice (el numero de interfaz), -- el tipo de interfaz, el conector y una descripcion del mismo. telProdNpInterfAsigListInitialTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpInterfAsigListInitialEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Interfaces list. It is the existing configuration after the last reset of the router. The table index is the interface number." ::= { telProdNpInterfAsigListInitial 1 } telProdNpInterfAsigListInitialEntry OBJECT-TYPE SYNTAX TelProdNpInterfAsigListInitialEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry consists of the index (interface number), the interface type, the connector and a description of the same one." INDEX { telNpInterfAListInitialIndex } ::={ telProdNpInterfAsigListInitialTable 1 } TelProdNpInterfAsigListInitialEntry ::= SEQUENCE{ telNpInterfAListInitialIndex INTEGER, telNpInterfAListInitialType INTEGER, telNpInterfAListInitialConn INTEGER, telNpInterfAListInitialDescription DisplayString } telNpInterfAListInitialIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface number. It is the table index." ::={ telProdNpInterfAsigListInitialEntry 1 } telNpInterfAListInitialType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the interface type." ::={ telProdNpInterfAsigListInitialEntry 2 } telNpInterfAListInitialConn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the interface connector." ::={ telProdNpInterfAsigListInitialEntry 3 } telNpInterfAListInitialDescription OBJECT-TYPE SYNTAX DisplayString(SIZE(0..49)) ACCESS read-only STATUS mandatory DESCRIPTION "Hardware description of the interface." ::={ telProdNpInterfAsigListInitialEntry 4 } -- Grupo telProdNpInterfAsig telProdNpInterfAsig OBJECT IDENTIFIER ::= { telProdNpConfInterfaceAsignation 2 } -- Tabla telProdNpInterfAsigTable. -- Esta tabla permite la asignacion de interfaces -- a los conectores del router : linea LAN (el tipo de interfaz asociado: -- Ethernet o TokenRing lo define el Hardware); las lineas WAN pueden tener -- asociados interfaces del tipo :Frame Relay (1), PPP (2), PPPAS (3), -- SDLC (4), X25 (5), X28(6), ATPPP-DIAL (7) ; la segunda linea LAN, cuyo -- tipo de interfaz asociado, Ethernet o Token Ring, lo define el Hardware; -- las lineas RDSI pueden tener asociados interfaces del tipo: FR-DIAL (20), -- PPP-DIAL(21), X25-DIAL (22); conector interno, que puede tener asociado -- XST y el interfaz 270. -- La tabla de DataLink contiene la informacion del indice, conector y -- el valor del interfaz asociado a dicho conector. -- El indice puede tomar estos valores: -- lan1 (1), linea1 (2), linea2 (3), linea3 (4), linea4 (5), linea5 (6), -- linea6 (7), linea7 (8), linea8 (9), lan2 (16), rdsi1 (20), rdsi2 (21), -- interno (30), router->nodo (31), nodo->router (32), int-270 (33). -- El conector puede tomar estos valores: -- lan (1), linea1 (2), linea2 (3), linea3 (4), linea4 (5), linea5 (6), -- linea6 (7), linea7 (8), linea8 (9), rdsi1 (10), rdsi2 (11), lan2 (16), -- interno (0), router-> nodo (0), nodo->router (0), con-270 (0). telProdNpInterfAsigTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpInterfAsigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Connectors list. The table index is the value of the line index: LAN, WAN, ISDN, INTERNAL, ROUTER-> NODE, NODE->ROUTER or CON-270." ::= { telProdNpInterfAsig 1 } telProdNpInterfAsigEntry OBJECT-TYPE SYNTAX TelProdNpInterfAsigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the index, the connector number and the interface value." INDEX { telNpInterfAsigIndex } ::={ telProdNpInterfAsigTable 1 } TelProdNpInterfAsigEntry ::= SEQUENCE{ telNpInterfAsigIndex INTEGER, telNpInterfAsigConector INTEGER, telNpInterfAsigValue INTEGER } telNpInterfAsigIndex OBJECT-TYPE SYNTAX INTEGER{ lan1(1), line1(2), line2(3), line3(4), line4(5), line5(6), line6(7), line7(8), line8(9), lan2(16), isdn1(20), isdn2(21), internal(30), router-node(31), node-router(32), int-270(33) } ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the hardware which indexes the table. The only possible values are: lan1(1), line1(2), line2(3),line3(4), line4(5), line5(6), line6(7), line7(8), line8(9), lan2(16), isdn1(20), isdn2(21), internal(30), router-node(31), node-router(32), int-270(33)." ::={ telProdNpInterfAsigEntry 1 } telNpInterfAsigConector OBJECT-TYPE SYNTAX INTEGER{ lan(1), line1(2), line2(3), line3(4), line4(5), line5(6), line6(7), line7(8), linea8(9), isdn1(10), isdn2(11), lan2(16), others(0) --internal(0), --router-node(0), --node-router (0), --con-270 (0) } ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the connector." ::={ telProdNpInterfAsigEntry 2 } telNpInterfAsigValue OBJECT-TYPE SYNTAX INTEGER{ ok(2), error(3), indefinite(4), fr(61), ppp(59), pppas(55), sdlc(63), x25(61444), x28(11), atppp-dial(31), chb1-dial-fr(40), chb1-dial-ppp(41), chb1-dial-x25(61442), chb2-dial-fr(240), chb2-dial-ppp(241), chb2-dial-x25(261442), ch-mppp(75), xst(61445), int-270(61446) } ACCESS read-write STATUS mandatory DESCRIPTION "This variable allows associating a certain protocol type to the connector. In reading, this variable shows if the last allocation attempt were in success (2, ok), in error (3) or if still any attempt has not been carried out to assign a protocol to a connector (4, indefinite). In writing, it is only permitted to do a set to some of the values allowed like possible protocols associated to the connectors. To LAN lines, the protocol type is determined by the device hardware (Ethernet or TokenRing), reason why they do not admit Set operations that try to modify this protocol. Possible values for WAN lines are: fr (61), ppp (59), pppas (55), sdlc (63), x25 (61444), x28 (11), atppp-dial (31). ISDN lines can have two B channels, and its possible values are: B1 channel: chb1-dial-fr (40), chb1-dial-ppp (41), chb1-dial-x25 (61442) B2 channel: chb2-dial-fr (240), chb2-dial-ppp (241), chb2-dial-x25 (261442) An interface MultiLink PPP can also be assigned to ISDN lines, independently of the type of B channel, since these interfaces are not associated to any specific connector, nor physical line. ch-mppp (75) When doing the allocation, the dial-fr and dial-ppp will always go first and the MPPP after. The INTERNAL interface can take the value xst (61445), associated to index 30. There can be another INTERNAL interface with the value int-270 (61446), associated to the index 33. This is the only way to assign the values, and any interrelation different from the associations above indicated cannot be done. When a atppp-dial (null, value 31) is assigned to one of the WAN lines by first time, two interfaces (one after the other) are added: one for the ATI of the B channel type: X.25(value 18), and another for the particular DIAL (PPP). The allocation of the DIAL interfaces (X25-DIAL, FR-DIAL, PPP-DIAL) is complex. In general, the allocation is done starting for the connector 1 and after with the connector 2. In general, chb1 will be assigned first and chb2 after. If it is tried to generate a chb2 in a connector which doesn't have chb1, it returns error. In case a same connector has FR-dial and/or PPP-dial in a B channel and X25-dial in the other B channel, FR-dial and / or PPP-dial will be assigned to chb1. I. If the device has an only basic access (ISDN) and can carry two B channels, then these will be chb1 and chb2. They are always present and are modified individually. II. If the device has two basic access and can carry two B channels, there are three possibilities: that they are associate one to each basic access, that two B channels are associate to one of the accesses and the other one is empty, and the inverse thing to the previous thing. A. CHB1 ALLOCATION: *If a chb1-x25 is assigned to a connector, two things can occur: - There is chb1 for that connector: If it is chb1-x25 nothing is done. If it is chb1-rdsi-base, it is changed to chb1-x25 and chb1-rdsi-base is eliminated. The PPP-DIAL or FR-DIAL which it has associate are eliminated if there is no another RDSI-BASE in that connector, otherwise they stay associated to that RDSI-BASE. - There isn't chb1 for that connector: In this case, the other connector has two B channels, chb1 and chb2. Therefore chb2 of the other connector is modified. If it is ch2-x25, it is associated to it to the chb1 of the initial connector. If it is chb2-rdsi-base, it is changed to chb1-x25 of the initial connector and chb2-rdsi-base is eliminated from its connector. The PPP-DIAL or FR-DIAL which it has associate, are eliminated if there is no another RDSI-BASE in its connector, otherwise they stay associated to that RDSI-BASE. *If a chb1-rdsi-base is assigned to a connector, two things can occur: - There is chb1 for that connector: If it is chb1-x25, it is changed to chb1-rdsi-base. If it is chb1-rdsi-base, PPP-DIAL or FR-DIAL is added to that chb1-rdsi-base. - There isn't chb1 for that connector: In this case, the other connector has two B channels, chb1 and chb2. Therefore chb2 of the other connector is modified. If it is chb2-x25, it is changed to chb1-rdsi-base. of the initial connector. If it is chb2-rdsi-base, it is changed to chb1-rdsi-base of the initial connector and chb2-rdsi-base is eliminated from its connector. The PPP-DIAL or FR-DIAL which it has associate, are eliminated if there is no another RDSI-BASE in its connector, otherwise they stay associated to that RDSI-BASE. B. CHB2 ALLOCATION: *If a chb2-x25 is assigned to a connector (this is always done after having associated the chb1 to that connector), two things can occur: - There is chb2 for that connector: If it is chb2-x25 nothing is done. If it is chb2-rdsi-base, it is changed to chb2-x25 and chb2-rdsi-base is eliminated. The PPP-DIAL or FR-DIAL which it has associate are eliminated if there is no another RDSI-BASE in that connector, otherwise they stay associated to that RDSI-BASE. - There isn't chb2 for that connector: In this case, the other connector has a B channel (chb1), therefore chb1 of the other connector is modified. If it is ch1-x25, it is associated to it to the chb2 of the initial connector. If it is chb1-rdsi-base, it is changed to chb2-x25 of the initial connector and chb1-rdsi-base is eliminated from its connector. The PPP-DIAL or FR-DIAL which it has associate, are eliminated if there is no another RDSI-BASE in its connector, otherwise they stay associated to that RDSI-BASE. *If a chb2-rdsi-base is assigned to a connector (this is always done after having associated the chb1 to that connector), two things can occur: - There is chb1 for that connector: If it is chb2-x25, it is changed to chb2-rdsi-base. If it is chb2-rdsi-base, PPP-DIAL or FR-DIAL is added to that chb2-rdsi-base. - There isn't chb2 for that connector: In this case, the other connector has a B channel (chb1), therefore the chb1 of the other connector is modified. If it is chb1-x25, it is changed to chb2-rdsi-base. of the initial connector. If it is chb1-rdsi-base, it is changed to chb2-rdsi-base of the initial connector and chb1-rdsi-base is eliminated from its connector. The PPP-DIAL or FR-DIAL which it has associate, are eliminated if there is no another RDSI-BASE in its connector, otherwise they stay associated to that RDSI-BASE. III. If the device has two basic accesses and can carry 4 B channels, they will be chb1 and chb2 for the RDSI1, and chb1 and chb2 for the RDSI2. They are always present and are modified individually. When a FR-DIAL or PPP-DIAL is assigned to one of the ISDN lines by first time, two interfaces are added: one for the ISDN and another for the particular DIAL (FR or PPP). A X25-DIAL by each ISDN basic access can only be assigned. There can be several FR-DIAL and PPP-DIAL in a same ISDN basic access. X25-dial cannot coexist with FR-dial nor PPP-dial in a same ISDN basic access. For that reason, when assigning a X25-dial to an ISDN connector, the ISDN-base is eliminated, and if there is no another RDSI-base associated to that connector, possible PPP-dial and FR-dial are also eliminated; the same happens if there is a X25-dial in a basic access and it is tried to add a FR-dial or a PPP-dial: then the X25-DIAL is eliminated. The maximum number of interfaces that the device can have is 40. In addition, there can be 6 DIAL in total between the two basic accesses, for each ISDN basic access." ::={ telProdNpInterfAsigEntry 3 } -- Grupo telProdNpInterfAsigListModify telProdNpInterfAsigListModify OBJECT IDENTIFIER ::= { telProdNpConfInterfaceAsignation 3 } -- Tabla telProdNpInterfAsigListModifyTable -- La tabla de configuracion actual de interfaces del ROUTER. -- La tabla de interfaces contiene el indice (el numero de interfaz), -- la variable de borrado de un interfaz (siempre que este permitido), -- el tipo de interfaz, el conector, una descripcion de tipo de interfaz -- y del conector. telProdNpInterfAsigListModifyTable OBJECT-TYPE SYNTAX SEQUENCE OF TelProdNpInterfAsigListModifyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "List of the modified interfaces. It is the actual interfaces configuration, considering the modifications done in the router. The table index is the interface number." ::= { telProdNpInterfAsigListModify 1 } telProdNpInterfAsigListModifyEntry OBJECT-TYPE SYNTAX TelProdNpInterfAsigListModifyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information of the index (the interface number), the variable to delete an interface (whenever it is permitted), the interface type, the connector, and a description of the interface type and connector." INDEX { telNpInterfAListModifyIndex } ::={ telProdNpInterfAsigListModifyTable 1 } TelProdNpInterfAsigListModifyEntry ::= SEQUENCE{ telNpInterfAListModifyIndex INTEGER, telNpInterfAListModifyDelInterf INTEGER, telNpInterfAListModifyType INTEGER, telNpInterfAListModifyConn INTEGER, telNpInterfAListModifyTypeDescription DisplayString, telNpInterfAListModifyConnDescription DisplayString, telNpInterfAListModifyAdminStat INTEGER, telNpInterfAListModifyOperStat INTEGER } telNpInterfAListModifyIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interface type. It is the index table." ::={ telProdNpInterfAsigListModifyEntry 1 } telNpInterfAListModifyDelInterf OBJECT-TYPE SYNTAX INTEGER{ valid(1), last-set-ok(2), last-set-non-ok(3), indeterminate(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This variable allows deleting an interface. The operation is done if it is permitted to delete this interface. A set to 1 must be done to delete the interface (it returns 1(valid) if it is done with success and error in opposite case). Get returns 2(last-set-ok) if the last set was done with success, 3(last-set-non-ok) if it resulted in error and 4 in another case." ::={ telProdNpInterfAsigListModifyEntry 2 } telNpInterfAListModifyType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the interface type." ::={ telProdNpInterfAsigListModifyEntry 3 } telNpInterfAListModifyConn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number associated to the interface connector." ::={ telProdNpInterfAsigListModifyEntry 4 } telNpInterfAListModifyTypeDescription OBJECT-TYPE SYNTAX DisplayString(SIZE(0..50)) ACCESS read-only STATUS mandatory DESCRIPTION "Description of the interface type." ::={ telProdNpInterfAsigListModifyEntry 5 } telNpInterfAListModifyConnDescription OBJECT-TYPE SYNTAX DisplayString(SIZE(0..50)) ACCESS read-only STATUS mandatory DESCRIPTION "Description of the connector type." ::={ telProdNpInterfAsigListModifyEntry 6 } telNpInterfAListModifyAdminStat OBJECT-TYPE SYNTAX INTEGER{ up(1), down(2), ignored(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Administrative or wished status of the interface." ::={ telProdNpInterfAsigListModifyEntry 7 } telNpInterfAListModifyOperStat OBJECT-TYPE SYNTAX INTEGER{ up(1), down(2), ignored(3), unknown(4), dormant(5), not-present(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Operative state of the interface." ::={ telProdNpInterfAsigListModifyEntry 8 } -- Variable telNpInterfADelAll telNpInterfADelAll OBJECT-TYPE SYNTAX INTEGER{ set(1), last-set-ok(2), last-set-failed (3), indeterminate(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This variable deletes all interfaces configuration that has been modified until the moment." ::={ telProdNpConfInterfaceAsignation 4 } END