-- extracted from draft-ietf-pwe3-pw-mpls-mib-06.txt -- at Thu Jul 8 06:21:50 2004 PW-MPLS-DRAFT06-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF StorageType FROM SNMPv2-TC InterfaceIndexOrZero FROM IF-MIB MplsTunnelIndex, MplsTunnelInstanceIndex, MplsLdpIdentifier, MplsLsrIdentifier FROM MPLS-TC-STD-MIB MplsIndexType FROM MPLS-LSR-STD-MIB PwVcIndexType, pwStdMIB FROM PW-TC-DRAFT05-MIB pwVcIndex FROM PW-DRAFT05-MIB ; pwVcMplsMIB MODULE-IDENTITY LAST-UPDATED "200406131200Z" -- 13 June 2004 12:00:00 GMT ORGANIZATION "Pseudo Wire Edge to Edge Emulation (PWE3) Working Group" CONTACT-INFO " David Zelig Postal: Corrigent Systems 126, Yigal Alon St. Tel Aviv, ISRAEL Phone: +972-3-6945273 E-mail: davidz@corrigent.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Tel: +1-978-497-3051 Email: tnadeau@cisco.com Dave Danenberg Email: dave_danenberg@yahoo.com Sharon Mantin Postal: AxONLink (Israel) Ltd 9 Bareket St. Petah Tikva 49517, Israel Tel: +972-3-9263972 Email: sharon.mantin@axonlink.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module complements the PW MIB module for PW operation over MPLS. Copyright (C) The Internet Society (date). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. -- RFC Ed.: replace yyyy with actual RFC number & remove this note " -- Revision history. REVISION "200406131200Z" -- 13 June 2004 12:00:00 GMT DESCRIPTION "Draft-ietf-pwe3-pw-mpls-mib-06 version. Changes from previous version: 1) Compliance section details. " REVISION "200402121200Z" -- 12 February 2004 12:00:00 GMT DESCRIPTION "Draft-ietf-pwe3-pw-mpls-mib-05 version. Changes from previous version: 1) Add inbound/outbound index for the nonTe mapping table 2) Clarify the pwVcMplsTeMappingTunnelInstance usage in pwVcMplsTeMappingTable. 3) Remove an index from pwVcMplsOutboundTable and adding an indication of Te or non-TE usage. 4) Removing the RowStatus from the outbound tables since it possible to configure a PW to a single TE tunnel head-end and/or a single nonTE tunnel, so the agent can open the row automatically. 5) Adding a nonTe inbound table in order to enable a quick search for a PW based on pwVcIndex. " REVISION "200311301200Z" -- 30 November 2003 12:00:00 EST DESCRIPTION "Draft-ietf-pwe3-pw-mpls-mib-04 version. Changes from previous version: 1) Adapting description to MIB boilerplate. 2) Module OID changed to PWE3 tree. 3) Sync descriptions of various items to table structure and removing unnecessary references. " REVISION "200307291200Z" -- 29 July 2003 12:00:00 EST DESCRIPTION "Draft-ietf-pwe3-pw-mpls-mib-02 version. Changes from previous version: 1) Removing inbound table (no strict mode and no knowledge of inbound tunnel). 2) Provisioning (i.e. RowCreate) done via mapping tables. Outbound table is now read only for sorted search for pwVcIndex. " REVISION "200206021200Z" -- 02 June 2002 12:00:00 EST DESCRIPTION "Draft-ietf-pwe3-pw-mpls-mib-00 version. Changes from previous version: 1) Splitting the mapping table into two tables, one for Non TE application and one for TE application. 2) Object types alignment with MPLS MIBs. " REVISION "200201291200Z" -- 29 January 2002 12:00:00 EST DESCRIPTION "Changes from previous version: 1) Add LDP entity association. 2) Clarify inbound/outbound directions. 3) Simplify indexing of outbound and inbound tables and providing get next variables. " REVISION "200111071200Z" -- 7 November 2001 12:00:00 EST DESCRIPTION "Changes from previous version: 1) Remove Vc instance from table indexing. 2) Update descriptions of indexing and protection. 3) Remove the need for MPLS-LSR in case of VC only. 4) Change pwVcMplsMplsType to BITS in order to enable multiple types of outer tunnel. 5) Add ifindex to outer tunnel tables to support vcOnly option. 6) change naming of outbound, inbound and mapping tables to reflect addition of VC only port ifindexes. 7) Adapt order of items in mapping table to SNMP convention. " REVISION "200107111200Z" -- July 11 2001 12:00:00 EST DESCRIPTION "draft-zelig-pw-mib-00.txt - initial version" -- NOTE: original draft left this OID as "{ pwStdMIB x }" pending -- assignment by IANA; no real assignment has been fabricated here. ::= { pwStdMIB 0 } -- the value 3 is requested for this -- specific Module. -- Top-level components of this MIB. -- Tables, Scalars pwVcMplsObjects OBJECT IDENTIFIER ::= { pwVcMplsMIB 1 } -- Conformance pwVcMplsConformance OBJECT IDENTIFIER ::= { pwVcMplsMIB 2 } -- PW MPLS table pwVcMplsTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcMplsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table controls MPLS specific parameters when the PW is going to be carried over MPLS PSN." ::= { pwVcMplsObjects 1 } pwVcMplsEntry OBJECT-TYPE SYNTAX PwVcMplsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents parameters specific to MPLS PSN for a pseudo wire (PW). The row is created automatically by the local agent if the pwVcPsnType is MPLS. It is indexed by pwVcIndex, which uniquely identifying a singular PW. " INDEX { pwVcIndex } ::= { pwVcMplsTable 1 } PwVcMplsEntry ::= SEQUENCE { pwVcMplsMplsType BITS, pwVcMplsExpBitsMode INTEGER, pwVcMplsExpBits Unsigned32, pwVcMplsTtl Unsigned32, pwVcMplsLocalLdpID MplsLdpIdentifier, pwVcMplsLocalLdpEntityID MplsLsrIdentifier, pwVcMplsPeerLdpID MplsLdpIdentifier, pwVcMplsStorageType StorageType } pwVcMplsMplsType OBJECT-TYPE SYNTAX BITS { mplsTe (0), mplsNonTe (1), vcOnly (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the outer tunnel types, if exists. mplsTe(0) is used if the outer tunnel was set-up by MPLS-TE, and mplsNonTe(1) is used the outer tunnel was set up by LDP or manually. Combination of mplsTe(0) and mplsNonTe(1) may exist together. vcOnly(2) is used if there is no outer tunnel label, i.e. in static provisioning without MPLS tunnel. vcOnly(2) cannot be combined with mplsNonTe(1) or mplsTe(0)." DEFVAL { { mplsNonTe } } ::= { pwVcMplsEntry 1 } pwVcMplsExpBitsMode OBJECT-TYPE SYNTAX INTEGER { outerTunnel (1), specifiedValue (2), serviceDependant (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the way the PW shim label EXP bits are to be determined. The value of outerTunnel(1) is used where there is an outer tunnel - pwVcMplsMplsType is mplsTe(0) or mplsNonTe(1). Note that in this case there is no need to mark the PW label with the EXP bits since the PW label is not visible to the intermediate nodes. If there is no outer tunnel, specifiedValue(2) indicates that the value is specified by pwVcMplsExpBits, and serviceDependant(3) indicates that the EXP bits are setup based on a rule specified in the emulated service specific tables, for example when the EXP bits are a function of 802.1p marking for Ethernet emulated service." DEFVAL { outerTunnel } ::= { pwVcMplsEntry 2 } pwVcMplsExpBits OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the MPLS EXP bits to be used on the PW shim label if pwVcMplsExpBitsMode is specifiedValue(2), zero otherwise." DEFVAL { 0 } ::= { pwVcMplsEntry 3 } pwVcMplsTtl OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the PW TTL value to be used on the PW shim label." DEFVAL { 2 } ::= { pwVcMplsEntry 4 } pwVcMplsLocalLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The local LDP identifier of the LDP entity creating this PW in the local node. As the PW labels are always set from the per platform label space, the last two octets in the LDP ID MUST be always both zeros." REFERENCE "'LDP specifications', RFC 3036 section 2.2.2." ::= { pwVcMplsEntry 5 } pwVcMplsLocalLdpEntityID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The local node LDP Entity ID of the LDP entity creating this PW. Should return the value of all zeros if not used." ::= { pwVcMplsEntry 6 } pwVcMplsPeerLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The peer LDP identifier as identified from the LDP session. Should return the value of zero if not applicable or not known yet." ::= { pwVcMplsEntry 7 } pwVcMplsStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the storage type for this row." ::= { pwVcMplsEntry 8 } -- End of PW MPLS table -- Pseudo Wire MPLS Outbound Tunnel table pwVcMplsOutboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reports and configure the current outbound MPLS tunnels (i.e. toward the PSN) or the physical interface in case of PW label only that carry the PW traffic. It also reports the current outer tunnel and LSP which forward the PW traffic." ::= { pwVcMplsObjects 2 } pwVcMplsOutboundEntry OBJECT-TYPE SYNTAX PwVcMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table configured the outer tunnel used for carrying the PW traffic toward the PSN. In the case of PW label only, it configures the interface that will carry the PW traffic. An entry in this table augments the pwVcMplsEntry, and is created automatically when the corresponding row has been created by the agent in the pwVcMplsEntry. This table points to the appropriate MPLS MIB module. In the MPLS-TE case, the 3 variables relevant to the indexing of a TE tunnel head-end are used as in MPLS-TE-STD-MIB are to be configured, and the tunnel instance indicates the LSP that is currently in use for forwarding the traffic. In case of signaled Non-TE MPLS (an outer tunnel label assigned by LDP) the table points to the XC entry in the LSR-STD-MIB. If the Non-TE MPLS tunnel is manually configured, the operator configure the XC pointer to this tunnel. In case of PW label only (no outer tunnel) the ifIndex of the port to carry the PW is configured here. It is possible to associate a PW to one TE tunnel head-end and a non-TE tunnel together. An indication in this table will report the currently active one, In addition, in the TE case the table reports the active tunnel instance (i.e. the specific LSP in use). " AUGMENTS { pwVcMplsEntry } ::= { pwVcMplsOutboundTable 1 } PwVcMplsOutboundEntry ::= SEQUENCE { pwVcMplsOutboundLsrXcIndex MplsIndexType, pwVcMplsOutboundTunnelIndex MplsTunnelIndex, pwVcMplsOutboundTunnelInstance MplsTunnelInstanceIndex, pwVcMplsOutboundTunnelLclLSR MplsLsrIdentifier, pwVcMplsOutboundTunnelPeerLSR MplsLsrIdentifier, pwVcMplsOutboundIfIndex InterfaceIndexOrZero, pwVcMplsOutboundTunnelTypeInUse INTEGER } pwVcMplsOutboundLsrXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsNonTe(1) bit is set, and MUST return a value of zero otherwise. If the outer tunnel is signaled, the object is read-only and indicate the XC index in the MPLS-LSR-STD-MIB of the outer tunnel toward the peer. Otherwise (tunnel is set-up manually) the operator define the XC index of the manually created outer tunnel through this object. " ::= { pwVcMplsOutboundEntry 1 } pwVcMplsOutboundTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is Part of set of indexes for outbound tunnel. The operator set this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwVcMplsOutboundEntry 2 } pwVcMplsOutboundTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It indicates the actual tunnel instance that is currently active and carrying the PW traffic - it should return the value of zero until if the information from the MPLS-TE application is not yet known. " ::= { pwVcMplsOutboundEntry 3 } pwVcMplsOutboundTunnelLclLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsTe(0) bit is set, and MUST return a value of all zeros otherwise. It is part of set of indexes for outbound tunnel. The operator set this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwVcMplsOutboundEntry 4 } pwVcMplsOutboundTunnelPeerLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is part of set of indexes for outbound tunnel. It is typically equal to pwVcPeerAddr. " ::= { pwVcMplsOutboundEntry 5 } pwVcMplsOutboundIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwVcMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. The operator configure the ifIndex of the outbound port in this case. " ::= { pwVcMplsOutboundEntry 6 } pwVcMplsOutboundTunnelTypeInUse OBJECT-TYPE SYNTAX INTEGER { notYetKnown (1), mplsTe (2), mplsNonTe (3), vcOnly (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current tunnel that is carrying the PW traffic. The value of notYetKnown(1) should be used if the agent is currently unable to determine which tunnel or interface is carrying the PW, for example because both tunnels are in operational status down. " ::= { pwVcMplsOutboundEntry 7 } -- End of PW MPLS Outbound Tunnel table -- PW MPLS inbound table pwVcMplsInboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the PW LDP XC entry in the MPLS-LSR-STD-MIB for signaled PWs. " ::= { pwVcMplsObjects 3 } pwVcMplsInboundEntry OBJECT-TYPE SYNTAX PwVcMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table is created by the agent for each signaled PW, and shows the XC index related to the PW signaling in the inbound direction in the MPLS-LSR-STD-MIB that controls and display the information for all the LDP signaling processes in the local node. " INDEX { pwVcIndex } ::= { pwVcMplsInboundTable 1 } PwVcMplsInboundEntry ::= SEQUENCE { pwVcMplsInboundXcIndex MplsIndexType } pwVcMplsInboundXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The XC index representing this PW in the inbound direction. Should return the value of zero if the information is not yet known." ::= { pwVcMplsInboundEntry 1 } -- End of PW MPLS inbound table -- PW to Non-TE mapping Table. pwVcMplsNonTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates outbound Tunnel to a PW in non-TE applications, maps the PW to it's (inbound) XC entry, and indicates the PW to physical interface mapping for a PW label to physical interface a PW label is in use without outer tunnel. " ::= { pwVcMplsObjects 4 } pwVcMplsNonTeMappingEntry OBJECT-TYPE SYNTAX PwVcMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table displays the association between the PW and - it's non-TE MPLS outbound outer Tunnel or, - it's XC entry in the MPLS-LSR-STD-MIB, - it's physical interface if there is no outer tunnel (PW label only) and manual configuration. Rows are created in this table by the by the agent depending on the setting of pwVcMplsMplsType: - If pwVcMplsMplsType mplsNonTe(1) bit is set, the agent creates a row for the outbound direction (pwVcMplsNonTeMappingDirection set to psnBound(1)). The pwVcMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PSN bound outer tunnel. pwVcMplsNonTeMappingIfIndex MUST be zero for this row. - If pwVcMplsMplsType vcOnly(2) bit is set, the agent creates a row for the outbound direction (pwVcMplsNonTeMappingDirection set to psnBound(1)). The pwVcMplsNonTeMappingIfIndex holds the ifIndex of the physical port this PW will use in the outbound direction. pwVcMplsNonTeMappingXcIndex MUST be zero for this row. - If the PW has been set-up by signaling protocol (i.e. pwVcOwner equal pwIdFecSignaling(2) or genFecSignaling(3)), the agent creates a row for the inbound direction (pwVcMplsNonTeMappingDirection set to fromPsn(2)). The pwVcMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PW LDP generated XC entry. pwVcMplsNonTeMappingIfIndex MUST be zero for this row. An application can use this table to quickly retrieve the PW carried over specific non-TE MPLS outer tunnel or physical interface. " INDEX { pwVcMplsNonTeMappingDirection, pwVcMplsNonTeMappingXcIndex, pwVcMplsNonTeMappingIfIndex, pwVcMplsNonTeMappingVcIndex } ::= { pwVcMplsNonTeMappingTable 1 } PwVcMplsNonTeMappingEntry ::= SEQUENCE { pwVcMplsNonTeMappingDirection INTEGER, pwVcMplsNonTeMappingXcIndex MplsIndexType, pwVcMplsNonTeMappingIfIndex InterfaceIndexOrZero, pwVcMplsNonTeMappingVcIndex PwVcIndexType } pwVcMplsNonTeMappingDirection OBJECT-TYPE SYNTAX INTEGER { psnBound (1), fromPsn (2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the conceptual XC row identifying Tunnel to PW mappings, indicating the direction of packet flow the entry is related too. psnBound(1) indicates that the entry is related to packets toward the PSN. fromPsn(2) indicates that the entry is related to packets coming from the PSN. " ::= { pwVcMplsNonTeMappingEntry 1 } pwVcMplsNonTeMappingXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwVcMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwVcMplsNonTeMappingEntry 2 } pwVcMplsNonTeMappingIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwVcMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwVcMplsNonTeMappingEntry 3 } pwVcMplsNonTeMappingVcIndex OBJECT-TYPE SYNTAX PwVcIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represent the PW in the pwVcTable." ::= { pwVcMplsNonTeMappingEntry 4 } -- End of PW to Non-TE mapping Table. -- PW to TE MPLS tunnels mapping Table. pwVcMplsTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table enable the retrieval of a PW association to the outbound MPLS tunnel for MPLS-TE applications." ::= { pwVcMplsObjects 5 } pwVcMplsTeMappingEntry OBJECT-TYPE SYNTAX PwVcMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents the association between a PW and it's MPLS-TE outer (head-end) Tunnel. An application can use this table to quickly retrieve the list of the PWs that are configured on a specific MPLS TE outer tunnel. The pwVcMplsTeMappingTunnelInstance reports the actual LSP out of the tunnel head-end that is currently forwarding the traffic. The table in indexed by the head-end indexes of a TE tunnel and the PW index. " INDEX { pwVcMplsTeMappingTunnelIndex, pwVcMplsTeMappingTunnelInstance, pwVcMplsTeMappingTunnelPeerLsrID, pwVcMplsTeMappingTunnelLocalLsrID, pwVcMplsTeMappingVcIndex } ::= { pwVcMplsTeMappingTable 1 } PwVcMplsTeMappingEntry ::= SEQUENCE { pwVcMplsTeMappingTunnelIndex MplsTunnelIndex, pwVcMplsTeMappingTunnelInstance MplsTunnelInstanceIndex, pwVcMplsTeMappingTunnelPeerLsrID MplsLsrIdentifier, pwVcMplsTeMappingTunnelLocalLsrID MplsLsrIdentifier, pwVcMplsTeMappingVcIndex PwVcIndexType } pwVcMplsTeMappingTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index for the conceptual row identifying the MPLS-TE tunnel that is carrying the PW traffic." ::= { pwVcMplsTeMappingEntry 1 } pwVcMplsTeMappingTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identify the MPLS-TE LSP that is carrying the PW traffic. Should return the value of zero if the information of the specific LSP is not yet known. Note that based on the recommendation in the MPLS-TC-STD-MIB, instance index 0 should refer to the configured tunnel interface." ::= { pwVcMplsTeMappingEntry 2 } pwVcMplsTeMappingTunnelPeerLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the Peer LSR when the outer tunnel is MPLS-TE based." ::= { pwVcMplsTeMappingEntry 3 } pwVcMplsTeMappingTunnelLocalLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the local LSR." ::= { pwVcMplsTeMappingEntry 4 } pwVcMplsTeMappingVcIndex OBJECT-TYPE SYNTAX PwVcIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represent the PW in the pwVcTable." ::= { pwVcMplsTeMappingEntry 5 } -- End of PW to TE MPLS tunnels mapping Table. -- conformance information pwVcMplsGroups OBJECT IDENTIFIER ::= { pwVcMplsConformance 1 } pwVcMplsCompliances OBJECT IDENTIFIER ::= { pwVcMplsConformance 2 } -- Compliance requirement for fully compliant implementations. pwMplsModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide full support for PW-MPLS MIB Module. Such devices can then be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwVcMplsGroup, pwVcMplsOutboundMainGroup, pwVcMplsInboundGroup, pwVcMplsMappingGroup } GROUP pwVcMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS TE tunnels to carry PW traffic. " OBJECT pwVcMplsMplsType DESCRIPTION "Support of vcOnly(2) is not required. At least one of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwVcMplsExpBitsMode DESCRIPTION "Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwVcMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity identifier for PW signaling. " OBJECT pwVcMplsLocalLdpEntityID MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity index for PW signaling. " OBJECT pwVcMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero MUST be supported if the implementation support non TE signaling of the outer tunnel. A read-write access MUST be supported if the implementation supports manually setting of the PW labels and carrying them over non-TE tunnels. " OBJECT pwVcMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero and read-write operations MUST be supported if the implementation supports manully configured PW without MPLS outer tunnel. " ::= { pwVcMplsCompliances 1 } -- Compliance requirement for Read Only compliant implementations. pwMplsModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read only support for PW-MPLS MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwVcMplsGroup, pwVcMplsOutboundMainGroup, pwVcMplsInboundGroup, pwVcMplsMappingGroup } GROUP pwVcMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS TE tunnels to carry PW traffic. " OBJECT pwVcMplsMplsType MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support of vcOnly(2) is not required. At least one of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwVcMplsExpBitsMode MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwVcMplsExpBits MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsLocalLdpEntityID MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation support non TE signaling of the outer tunnel. " OBJECT pwVcMplsOutboundTunnelIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsOutboundTunnelLclLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsOutboundTunnelPeerLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwVcMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation supports manually configured PW without MPLS outer tunnel. " ::= { pwVcMplsCompliances 2 } -- Units of conformance. pwVcMplsGroup OBJECT-GROUP OBJECTS { pwVcMplsMplsType, pwVcMplsExpBitsMode, pwVcMplsExpBits, pwVcMplsTtl, pwVcMplsLocalLdpID, pwVcMplsLocalLdpEntityID, pwVcMplsPeerLdpID, pwVcMplsStorageType } STATUS current DESCRIPTION "Collection of objects needed for PW over MPLS PSN configuration." ::= { pwVcMplsGroups 1 } pwVcMplsOutboundMainGroup OBJECT-GROUP OBJECTS { pwVcMplsOutboundLsrXcIndex, pwVcMplsOutboundIfIndex, pwVcMplsOutboundTunnelTypeInUse } STATUS current DESCRIPTION "Collection of objects needed for outbound association of PW and MPLS tunnel." ::= { pwVcMplsGroups 2 } pwVcMplsOutboundTeGroup OBJECT-GROUP OBJECTS { pwVcMplsOutboundTunnelIndex, pwVcMplsOutboundTunnelInstance, pwVcMplsOutboundTunnelLclLSR, pwVcMplsOutboundTunnelPeerLSR } STATUS current DESCRIPTION "Collection of objects needed for outbound association of PW and MPLS TE tunnel." ::= { pwVcMplsGroups 3 } pwVcMplsInboundGroup OBJECT-GROUP OBJECTS { pwVcMplsInboundXcIndex } STATUS current DESCRIPTION "Collection of objects needed for inbound PW presentation. This group MUST be supported if PW signaling through LDP is used." ::= { pwVcMplsGroups 4 } pwVcMplsMappingGroup OBJECT-GROUP OBJECTS { pwVcMplsNonTeMappingVcIndex, pwVcMplsTeMappingVcIndex } STATUS current DESCRIPTION "Collection of objects needed for mapping association of PW and MPLS tunnel." ::= { pwVcMplsGroups 5 } END -- of PW MPLS MIB Module