PANDATEL-GMF-MODEM-MIB DEFINITIONS ::= BEGIN -- This is the private mib group section for the GM-F modems. -- Because these modems must be installed in the PANDATEL modem rack -- the PANDATEL-MODEM-MIB also applies. -- Ver.1.06 Sep.13.1999 IMPORTS enterprises, Gauge FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 mdmSpecifics, device-id FROM PANDATEL-MODEM-MIB; -- ********************** THE MDM-GMF SUBTREE ****************************** -- the specific identifier is identical to the modem type integer -- of the GM-F modem entries in the PANDATEL-MODEM-MIB mdmModemTable. gmf-modem OBJECT IDENTIFIER ::= { device-id 202 } -- chassis-mib gmf OBJECT IDENTIFIER ::= { mdmSpecifics 202 } -- this subtree gmfModemTable OBJECT-TYPE SYNTAX SEQUENCE OF GmfTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains information about all GM-F converters in all racks." ::= { gmf 1 } gmfTableEntry OBJECT-TYPE SYNTAX GmfTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The index of the table." INDEX { mdmRack, mdmModem, mdmPosition } ::= { gmfModemTable 1 } GmfTableEntry ::= SEQUENCE { mdmRack INTEGER, mdmModem INTEGER, mdmPosition INTEGER, mdmModemName DisplayString, mdmInterfaceEmulationMode INTEGER, mdmModemProperty INTEGER, mdmLineEmulationMode INTEGER, mdmClockSystem INTEGER, mdmClockSource INTEGER, mdmDataRate INTEGER, mdmStartTimeslot INTEGER, mdmTimeslotSize INTEGER, mdmTimeslot16 INTEGER, mdmCRC4Generation INTEGER, mdmFramingMode INTEGER, mdmCodingMode INTEGER, mdmScrambler INTEGER, mdmRemoteAccessMode INTEGER, mdmForcedRemoteAccess INTEGER, mdmTDPhaseLocking INTEGER, mdmLineBuiltOut INTEGER, mdmCRC6Test INTEGER, mdmCRC6Status INTEGER, mdmCRC6Error Gauge } mdmRack OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index of the rack where the converter is installed." ::= { gmfTableEntry 1 } mdmModem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This entry displays the slot number where the corresponding converter is installed in the rack." ::= { gmfTableEntry 2 } mdmPosition OBJECT-TYPE SYNTAX INTEGER { local (1), remote (2) } ACCESS read-only STATUS mandatory DESCRIPTION "This entry displays the location of the corresponding converter: 'local' or 'remote'. The converter which is plugged into a managed rack is 'local', the counterpart is 'remote'." ::= { gmfTableEntry 3 } mdmModemName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The verbal name of this converter." ::= { gmfTableEntry 5 } mdmInterfaceEmulationMode OBJECT-TYPE SYNTAX INTEGER { other (1), dte (2), dce (3), te (4), nt (5), unknown (99) } ACCESS read-only STATUS mandatory DESCRIPTION "Interface mode of the unit: 'dte', 'dce', 'te' or 'nt'." ::= { gmfTableEntry 6 } mdmModemProperty OBJECT-TYPE SYNTAX INTEGER { other (1), e1 (2), t1 (3), unknown (99) } ACCESS read-only STATUS mandatory DESCRIPTION "This entry displays the speed class of the GM-F: 'e1' or 't1'." ::= { gmfTableEntry 7 } mdmLineEmulationMode OBJECT-TYPE SYNTAX INTEGER { other (1), te (4), nt (5), unknown (99) } ACCESS read-only STATUS mandatory DESCRIPTION "Line mode of the unit: 'te' or 'nt'." ::= { gmfTableEntry 8 } mdmClockSystem OBJECT-TYPE SYNTAX INTEGER { other (1), dual (2), single (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The clock system of the link: 'dual' or 'single'." ::= { gmfTableEntry 23 } mdmClockSource OBJECT-TYPE SYNTAX INTEGER { other (1), internal (2), remote (3), external (4) } ACCESS read-write STATUS mandatory DESCRIPTION "The clock source of the link: 'internal', 'external', or 'remote'." ::= { gmfTableEntry 24 } mdmDataRate OBJECT-TYPE SYNTAX INTEGER { other (1) } ACCESS read-write STATUS mandatory DESCRIPTION "The data rate at the interface in bits per seconds. The data rate at the remote counterpart changes simultaneously. A data rate of 2.048 Mbps (E1) automatically disables CRC4, sets mdmStartTimeslot to 'unframed', enables time slot 16, and disables remote access. A data rate of 1.984 Mbps (E1) automatically sets mdmStartTimeslot to 'timeslot-1', enables time slot 16 and sets mdmRemoteAccessMode to 'via timeslot 0 sa4-bit'. A data rate of 1.544 Mbps (T1) automatically sets mdmStartTimeslot to 'unframed' and disables remote access." ::= { gmfTableEntry 25 } mdmStartTimeslot OBJECT-TYPE SYNTAX INTEGER { timeslot-1 (1), timeslot-2 (2), timeslot-3 (3), timeslot-4 (4), timeslot-5 (5), timeslot-6 (6), timeslot-7 (7), timeslot-8 (8), timeslot-9 (9), timeslot-10 (10), timeslot-11 (11), timeslot-12 (12), timeslot-13 (13), timeslot-14 (14), timeslot-15 (15), timeslot-16 (16), timeslot-17 (17), timeslot-18 (18), timeslot-19 (19), timeslot-20 (20), timeslot-21 (21), timeslot-22 (22), timeslot-23 (23), timeslot-24 (24), timeslot-25 (25), timeslot-26 (26), timeslot-27 (27), timeslot-28 (28), timeslot-29 (29), timeslot-30 (30), timeslot-31 (31), unframed (98), other (99), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry determines the start time slot for framing. Start time slot and data rate must match. A start time slot which is too high will be ignored. The remote unit's configuration changes simultaneously." ::= { gmfTableEntry 26 } mdmTimeslotSize OBJECT-TYPE SYNTAX INTEGER { other (1), nx64k (2), nx56k (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry determines the size of the time slots: 'nx64k' or 'nx56k'. 'nx56k' is valid for T1 units only. The remote unit's configuration changes simultaneously." ::= { gmfTableEntry 27 } mdmTimeslot16 OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), enable (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry enables or disables time slot 16. If it is disabled, it will not be used for data transmission but for framing. Valid for E1 units only." ::= { gmfTableEntry 40 } mdmCRC4Generation OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), enable (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry enables or disables the generation of a CRC4 check sum. Valid for E1 units only." ::= { gmfTableEntry 41 } mdmFramingMode OBJECT-TYPE SYNTAX INTEGER { other (1), d4 (2), esf (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "The T1 framing mode: 'd4' or 'esf'. The remote unit's configuration changes simultaneously. Valid for T1 units only." ::= { gmfTableEntry 50 } mdmCodingMode OBJECT-TYPE SYNTAX INTEGER { other (1), ami (2), b8zs (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "The T1 coding mode: 'ami' or 'b8zs'. The remote unit's configuration changes simultaneously. Valid for T1 units only." ::= { gmfTableEntry 51 } mdmScrambler OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), enable (3) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry enables or disables scrambling." ::= { gmfTableEntry 63 } mdmRemoteAccessMode OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), via-next-free-timeslot (3), via-timeslot-0-Sa4-bit (4), via-unframed-line (6) } ACCESS read-write STATUS mandatory DESCRIPTION "The remote access mode: 'disable', 'via-next-free-timeslot', 'via-timeslot-0-Sa4-bit', or 'via-unframed-line'. The value 'via-next-free-timeslot' means that one time slot higher than the last data time slot is used for remote access. The value 'via-timeslot-0-Sa4-bit' means that the sa4-bit in time slot 0 is used for remote access (for E1 units only). The value 'via-unframed-line' is valied for data rates of 2048 Kbps (E1) or 1544 Kbps (T1) only. With a data rate of 1536 Kbps (T1). remote management is not available. The remote unit's configuration changes simultaneously." ::= { gmfTableEntry 64 } mdmForcedRemoteAccess OBJECT-TYPE SYNTAX INTEGER { off (1), on (2), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "Valid if 'mdmRemoteAccessMode' is set to 'via-unframed-line'. Activation of remote management: 'on' or 'off'. Status 'on' enables management of remote unit. During this process the link is restricted to management data. The transmission of user data is interrupted. Status 'off' disables management of remote unit. The link transmits user data." ::= { gmfTableEntry 65 } mdmTDPhaseLocking OBJECT-TYPE SYNTAX INTEGER { other (1), positive-clock-slope (2), negative-clock-slope (3), unknown (99), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry defines the data phase locking for I/F data: 'positive-clock-slope' or 'negative-clock-slope'." ::= { gmfTableEntry 67 } mdmLineBuiltOut OBJECT-TYPE SYNTAX INTEGER { other (1), dsx-1-0to133-ft (3), dsx-1-133to266-ft (4), dsx-1-266to399-ft (5), dsx-1-399to533-ft (6), dsx-1-533to655-ft (7), csu-0db (8), csu-7db5 (9), csu-15db (10), csu-22db5 (11), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "The T1 transmission mode of the unit. Valid for T1 units only." ::= { gmfTableEntry 68 } mdmCRC6Test OBJECT-TYPE SYNTAX INTEGER { other (1), start (3), stop (4), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "This entry enables the execution of a CRC6 test. Write requests with values other than 'start' or 'stop' will be rejected. Valid for T1 units only." ::= { gmfTableEntry 100 } mdmCRC6Status OBJECT-TYPE SYNTAX INTEGER { other (1), never-started (2), running (5), stopped (6), start-failed (7), not-available (100) } ACCESS read-only STATUS mandatory DESCRIPTION "This entry indicates the status of the CRC6 test. Valid for T1 units only." ::= { gmfTableEntry 101 } mdmCRC6Error OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "This entry indicates the number of errors detected during the last 60 seconds." ::= { gmfTableEntry 102 } END