OMNI-gx2RSW200-MIB DEFINITIONS ::= BEGIN

    IMPORTS
	Counter
					      FROM RFC1155-SMI
--	IpAddress, TimeTicks            
--					      FROM RFC1155-SMI
--	OBJECT-TYPE                     
--					      FROM RFC-1212
--	sysUpTime, DisplayString        
--					      FROM RFC1213-MIB
--	TRAP-TYPE                       
--					      FROM RFC-1215
--	gi, motproxies                   
--					      FROM NLS-BBNIDENT-MIB
	gx2Rsw200
					      FROM GX2HFC-MIB

	trapIdentifier,trapNetworkElemModelNumber,
	trapNetworkElemSerialNum, trapPerceivedSeverity,
	trapNetworkElemOperState, trapNetworkElemAlarmStatus,
	trapNetworkElemAdminState, trapNetworkElemAvailStatus,
	trapText, trapNETrapLastTrapTimeStamp, trapChangedObjectId,
	trapChangedValueInteger, trapChangedValueDisplayString
					      FROM NLSBBN-TRAPS-MIB;



	       -- This MIB module uses the extended OBJECT-TYPE macro as
	       -- defined in RFC1212 and the TRAP-TYPE macro as defined
	       -- in RFC 1215.

		   --REVISION	"4" Jan 20, 2003
		   --DESCRIPTION
		   --			Added revision and description comment section


		--    OMNISTAR RF Switch Module MIB MODULE

	-- This MIB module defines information for management of HFC networks
		-- 
		-- The MIB module assumes that all generic (static) network element
		-- information is defined in a different module such as the HFC module
		-- The MIB consists of two groups:
		-- the device type descriptor subgroup and 
		-- gx2Rsw200 Network Elements subgroup.
		-- The device type descriptor subgroup is used to define 
		-- parameters specific to gx2Rsw200 device type.
		-- These parameters are common across all network elements
		-- from gx2Rsw200 device type.
		--
		-- The gx2Rsw200 Network Elements subgroup is
		-- a list of gx2Rsw200 type elements in the
		-- current network topology with nominal
		-- and current parameter values for the
		-- individual network elements; the individual
		-- network elements are identified by  
		-- index from hfcCommonTable.
		-- That implies what hfcCommonTableIndex and
		-- gx2Rsw200TableIndex are equal for each individual
		-- network element.
		-- This table is an extension of the hfcCommonTable
		-- for all elements of gx2Lmc type.
		--
		-- Both groups are mandatory for management of gx2Lmc devices.

-- ****************************************************************************
		--
		-- All floating point numbers will be represented by an IEEE 32 Bit number.
		-- Conversion of this number must be done on the user interface to view the 
		-- actual floating point number. 
		--

		Float ::= Counter  -- UNSIGNED (32 BITS) 

-- ****************************************************************************

		-- gx2Rsw200 Device Descriptor subgroup.

		-- The device type descriptor subgroup is used to define 
		-- parameters specific to gx2Rsw200 device type.
		-- These parameters are common across all network elements
		-- from gx2Rsw200 device type.


		gx2Rsw200Descriptor OBJECT IDENTIFIER ::= {gx2Rsw200 1}



--*****************************************************************************
		--              gx2Rsw200 Table
		
		-- Contains a list of all gx2Rsw200 type devices in
		-- the network. Each device is characterized with
		-- current network topology information, with nominal
		-- and current parameter values for the
		-- individual network elements;
		--
		-- The individual network elements indentified by  
		-- index from hfcCommonTable.
		-- That implies what hfcCommonTableIndex and
		-- gx2Rsw200TableIndex are equal for each individual
		-- nettwork element.
		-- This table should be used as an extension of the hfcCommonTable
		-- for all elements of gx2Rsw200 type.


	       gx2Rsw200AnalogTable                    OBJECT-TYPE
			 SYNTAX             SEQUENCE OF Gx2Rsw200AnalogEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This table contains gx2Rsw200 specific parameters with
			  nominal and current values."
			 ::= { gx2Rsw200 2 }


	       gx2Rsw200AnalogEntry               OBJECT-TYPE
			 SYNTAX             Gx2Rsw200AnalogEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This list contains the analog parameters and descriptions."
			 INDEX { gx2Rsw200AnalogTableIndex }
			 ::= { gx2Rsw200AnalogTable  1}

--*****************************************************************************
	       gx2Rsw200DigitalTable                    OBJECT-TYPE
			 SYNTAX             SEQUENCE OF Gx2Rsw200DigitalEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This table contains gx2Rsw200 specific parameters with
			  nominal and current values."
			 ::= { gx2Rsw200 3 }

	       gx2Rsw200DigitalEntry               OBJECT-TYPE
			 SYNTAX             Gx2Rsw200DigitalEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This list contains digital parameters and descriptions."
			 INDEX { gx2Rsw200DigitalTableIndex }
			 ::= { gx2Rsw200DigitalTable  2}

--*****************************************************************************
	       gx2Rsw200StatusTable                    OBJECT-TYPE
			 SYNTAX             SEQUENCE OF Gx2Rsw200StatusEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This table contains gx2Rsw200 specific parameters with
			  nominal and current values."
			 ::= { gx2Rsw200 4 }

	       gx2Rsw200StatusEntry               OBJECT-TYPE
			 SYNTAX             Gx2Rsw200StatusEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This list contains Status parameters and descriptions."
			 INDEX { gx2Rsw200StatusTableIndex }
			 ::= { gx2Rsw200StatusTable  3}

--*****************************************************************************
	       gx2Rsw200FactoryTable                    OBJECT-TYPE
			 SYNTAX             SEQUENCE OF Gx2Rsw200FactoryEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This table contains gx2Rsw200 specific parameters with
			  nominal and current values."
			 ::= { gx2Rsw200 5 }

	       gx2Rsw200FactoryEntry               OBJECT-TYPE
			 SYNTAX             Gx2Rsw200FactoryEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This list contains Factory parameters and descriptions."
			 INDEX { gx2Rsw200FactoryTableIndex }
			 ::= { gx2Rsw200FactoryTable  4}

--*****************************************************************************

	       gx2Rsw200bHoldTimeTable                    OBJECT-TYPE
			 SYNTAX             SEQUENCE OF Gx2Rsw200bHoldTimeEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This table contains gx2Rsw200b specific parameters with
			  nominal and current values."
			 ::= { gx2Rsw200 6 }

	       gx2Rsw200bHoldTimeEntry               OBJECT-TYPE
			 SYNTAX             Gx2Rsw200bHoldTimeEntry
			 ACCESS             not-accessible
			 STATUS             mandatory
			 DESCRIPTION
			 "This list contains digital product class and the
			  associated RF channel parameters and descriptions."
			 INDEX { rxgx2Rsw200bHoldTimeTableIndex, rxgx2Rsw200bHoldTimeSpecIndex }
			 ::= { gx2Rsw200bHoldTimeTable  5}

--***********************************************************************

	      Gx2Rsw200AnalogEntry    ::= SEQUENCE  
	       {
		gx2Rsw200AnalogTableIndex         INTEGER,
		
		--           Analog Parameters

		rsw200labelModTemp			DisplayString (SIZE (0..80)),
		rsw200uomModTemp				DisplayString (SIZE (0..80)),
		rsw200majorHighModTemp			Float, 
		rsw200majorLowModTemp			Float, 
		rsw200minorHighModTemp			Float,
		rsw200minorLowModTemp			Float, 
		rsw200currentValueModTemp		Float, 
		rsw200stateFlagModTemp			INTEGER,
		rsw200minValueModTemp			Float,
		rsw200maxValueModTemp			Float,
		rsw200alarmStateModTemp			INTEGER,

		rsw200labelFanCurrent			DisplayString (SIZE (0..80)),
		rsw200uomFanCurrent			DisplayString (SIZE (0..80)),
		rsw200majorHighFanCurrent		Float, 
		rsw200majorLowFanCurrent		Float, 
		rsw200minorHighFanCurrent		Float,
		rsw200minorLowFanCurrent		Float, 
		rsw200currentValueFanCurrent		Float, 
		rsw200stateFlagFanCurrent		INTEGER,
		rsw200minValueFanCurrent		Float,
		rsw200maxValueFanCurrent 		Float,
		rsw200alarmStateFanCurrent		INTEGER
		}

		-- ****************  Digital Parameters ***********************
	     Gx2Rsw200DigitalEntry    ::= SEQUENCE  
	     {
		gx2Rsw200DigitalTableIndex         INTEGER,

		rsw200labelSwitchControl		DisplayString (SIZE (0..80)),
		rsw200enumSwitchControl			DisplayString (SIZE (0..80)),
		rsw200valueSwitchControl		INTEGER,
		rsw200stateflagSwitchControl   	INTEGER,

		rsw200labelRevertMode			DisplayString (SIZE (0..80)),
		rsw200enumRevertMode			DisplayString (SIZE (0..80)),
		rsw200valueRevertMode			INTEGER,
		rsw200stateflagRevertMode   		INTEGER,

		rsw200labelRevertTime			DisplayString (SIZE (0..80)),
		rsw200enumRevertTime			DisplayString (SIZE (0..80)),
		rsw200valueRevertTime			INTEGER,
		rsw200stateflagRevertTime  	 	INTEGER,

		rsw200labelSwitchState			DisplayString (SIZE (0..80)),
		rsw200enumSwitchState			DisplayString (SIZE (0..80)),
		rsw200valueSwitchState			INTEGER,
		rsw200stateflagSwitchState  	 	INTEGER,

		rsw200labelPriStatus			DisplayString (SIZE (0..80)),
		rsw200enumPriStatus			DisplayString (SIZE (0..80)),
		rsw200valuePriStatus			INTEGER,
		rsw200stateflagPriStatus  	 	INTEGER,

		rsw200labelSecStatus			DisplayString (SIZE (0..80)),
		rsw200enumSecStatus			DisplayString (SIZE (0..80)),
		rsw200valueSecStatus			INTEGER,
		rsw200stateflagSecStatus   		INTEGER,

		rsw200labelFactoryDefault		DisplayString (SIZE (0..80)),
		rsw200enumFactoryDefault		DisplayString (SIZE (0..80)),
		rsw200valueFactoryDefault		INTEGER,
		rsw200stateflagFactoryDefault   	INTEGER
		}

		-- ****************  Status Parameters ************************************
	     Gx2Rsw200StatusEntry    ::= SEQUENCE  
	     {
		gx2Rsw200StatusTableIndex         INTEGER,

		rsw200labelBoot				DisplayString (SIZE (0..80)),
		rsw200valueBoot				INTEGER,
		rsw200stateflagBoot			INTEGER,
		
		rsw200labelFlash				DisplayString (SIZE (0..80)),
		rsw200valueFlash				INTEGER,
		rsw200stateflagFlash			INTEGER,

		rsw200labelFactoryDataCRC 		DisplayString (SIZE (0..80)),
		rsw200valueFactoryDataCRC		INTEGER,
		rsw200stateflagFactoryDataCRC		INTEGER,

		rsw200labelAlarmDataCrc			DisplayString (SIZE (0..80)),
		rsw200valueAlarmDataCrc			INTEGER,
		rsw200stateflagAlarmDataCrc		INTEGER,

		rsw200labelRFSignalStatus		DisplayString (SIZE (0..80)),
		rsw200valueRFSignalStatus		INTEGER,
		rsw200stateflagRFSignalStatus		INTEGER,

		rsw200labelPriActiveStatus		DisplayString (SIZE (0..80)),
		rsw200valuePriActiveStatus		INTEGER,
		rsw200stateflagPriActiveStatus		INTEGER

		}


		-- ****************  Factory Parameters *************************************
       Gx2Rsw200FactoryEntry    ::= SEQUENCE  
       {
		gx2Rsw200FactoryTableIndex         INTEGER,
		rsw200bootControlByte  			INTEGER,
		rsw200bootStatusByte   			INTEGER,
		rsw200bank1CRC    			INTEGER,
		rsw200bank2CRC    			INTEGER,
		rsw200prgEEPROMByte    			INTEGER,
		rsw200factoryCRC    			INTEGER,
		rsw200calculateCRC    			INTEGER,
		rsw200hourMeter    			INTEGER,
		rsw200flashPrgCntA    			INTEGER,
		rsw200flashPrgCntB    			INTEGER,
		rsw200flashBankARev    			DisplayString (SIZE (0..80)),
		rsw200flashBankBRev    			DisplayString (SIZE (0..80))

		}

		-- ****************  Hold Time Parameters *************************************
	    Gx2Rsw200bHoldTimeEntry    ::= SEQUENCE  
	    {
		rxgx2Rsw200bHoldTimeTableIndex        INTEGER,
		rxgx2Rsw200bHoldTimeSpecIndex         INTEGER,   
		rxgx2Rsw200bHoldTimeData  			 INTEGER
		}



            -- ************** Analog Parameters ****************************
		gx2Rsw200AnalogTableIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object identifies the network
			    element. This index is equal to the
			    hfcCommonTableIndex for the same element."
			   ::= { gx2Rsw200AnalogEntry 1}

-- New Parameter

		rsw200labelModTemp              OBJECT-TYPE
			   SYNTAX           DisplayString (SIZE (0..80))
			   ACCESS           read-only
			   STATUS           optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Module Temperature Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 2}

		rsw200uomModTemp                OBJECT-TYPE
			   SYNTAX           DisplayString (SIZE (0..80))
			   ACCESS           read-only
			   STATUS           optional
			   DESCRIPTION
			   "The value of this object provides the Unit of Measure of the
			    Module Temperature Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 3}

		rsw200majorHighModTemp          OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Major High alarm value
			    of the Module Temperature Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 4}


		rsw200majorLowModTemp           OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Major Low alarm value
			    of the Module Temperature Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 5}

		rsw200minorHighModTemp          OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Minor High alarm value
			    of the Module Temperature Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 6}

		rsw200minorLowModTemp           OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Minor Low alarm value
			    of the Module Temperature Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 7}

		rsw200currentValueModTemp       OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Current value
			    of the Module Temperature Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 8}

		rsw200stateFlagModTemp          OBJECT-TYPE
			   SYNTAX           INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the Module Temperature Analog parameter. (0-Hidden	
			          1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200AnalogEntry 9}

		rsw200minValueModTemp           OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the minimum value
			    the Module Temperature Analog parameter can achive.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 10}

		rsw200maxValueModTemp           OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the maximum value
			    the Module Temperature Analog parameter can achive.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 11}

		rsw200alarmStateModTemp         OBJECT-TYPE
			   SYNTAX           INTEGER {
									noAlarm(1),
									majorLowAlarm(2),
									minorLowAlarm(3),
									minorHighAlarm(4),
									majorHighAlarm(5),
									informational(6)
									}
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the curent alarm state of
			    the Module Temperature Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 12}
-- New Parameter

		rsw200labelFanCurrent           OBJECT-TYPE
			   SYNTAX           DisplayString (SIZE (0..80))
			   ACCESS           read-only
			   STATUS           optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Fan Current Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 13}

		rsw200uomFanCurrent             OBJECT-TYPE
			   SYNTAX           DisplayString (SIZE (0..80))
			   ACCESS           read-only
			   STATUS           optional
			   DESCRIPTION
			   "The value of this object provides the Unit of Measure of the
			    Fan Current Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 14}

		rsw200majorHighFanCurrent       OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Major High alarm value
			    of the Fan Current Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 15}


		rsw200majorLowFanCurrent        OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Major Low alarm value
			    of the Fan Current Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 16}

		rsw200minorHighFanCurrent       OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Minor High alarm value
			    of the Fan Current Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 17}

		rsw200minorLowFanCurrent        OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Minor Low alarm value
			    of the Fan Current Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 18}

		rsw200currentValueFanCurrent    OBJECT-TYPE
			   SYNTAX           Float 
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the Current value
			    of the Fan Current Analog parameter.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 19}

		rsw200stateFlagFanCurrent       OBJECT-TYPE
			   SYNTAX           INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the Fan Current Analog parameter. (0-Hidden	
			          1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200AnalogEntry 20}

		rsw200minValueFanCurrent        OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the minimum value
			    the Fan Current Analog parameter can achive.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 21}

		rsw200maxValueFanCurrent        OBJECT-TYPE
			   SYNTAX           Float
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the maximum value
			    the Fan Current Analog parameter can achive.
			   This value is a floating point number that is represented as an IEEE 32 bit number."
			   ::= { gx2Rsw200AnalogEntry 22}

        rsw200alarmStateFanCurrent      OBJECT-TYPE
			   SYNTAX           INTEGER {
									noAlarm(1),
									majorLowAlarm(2),
									minorLowAlarm(3),
									minorHighAlarm(4),
									majorHighAlarm(5),
									informational(6)
									}
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object provides the curent alarm state of
			    the Fan Current Analog parameter."
			   ::= { gx2Rsw200AnalogEntry 23}

-- ************************ Digital parameters **********************************
		gx2Rsw200DigitalTableIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object identifies the network
			    element. This index is equal to the
			    hfcCommonTableIndex for the same element."
			   ::= { gx2Rsw200DigitalEntry 1}

-- New parameter

		rsw200labelSwitchControl           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Switch Control Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 2}

		rsw200enumSwitchControl              	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 3}


		rsw200valueSwitchControl         	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							primary(1),
							secondary(2)
					    		}
			   ACCESS           	read-write
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 4}

		rsw200stateflagSwitchControl     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 5}

		rsw200labelRevertMode	           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Revert Mode Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 6}

		rsw200enumRevertMode               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 7}


		rsw200valueRevertMode         	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							manual(1),
							autorevert(2),
							nonrevert(3)
					    		}
			   ACCESS           	read-write
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 8}

		rsw200stateflagRevertMode     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 9}

		rsw200labelRevertTime	     		OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Revert Time Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 10}

		rsw200enumRevertTime               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 11}


		rsw200valueRevertTime         	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							tensec(1),
							sixtysec(2),
							sixhundredsec(3)
					    		}
			   ACCESS           	read-write
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 12}

		rsw200stateflagRevertTime     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 13}

		rsw200labelSwitchState	           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Switch State Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 14}

		rsw200enumSwitchState               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 15}


		rsw200valueSwitchState         	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							primary(1),
							secondary(2)
					    		}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 16}

		rsw200stateflagSwitchState     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 17}

		rsw200labelPriStatus           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Primary Signal Status Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 18}

		rsw200enumPriStatus               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 19}


		rsw200valuePriStatus   	      	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							short(1),
							valid(2),
							invalid(3),
							open(4)
					    		}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 20}

		rsw200stateflagPriStatus     		OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 21}

		rsw200labelSecStatus      	     OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Secondary Signal Status Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 22}

		rsw200enumSecStatus               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 23}


		rsw200valueSecStatus       	  	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							short(1),
							valid(2),
							invalid(3),
							open(4)
					    		}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 24}

		rsw200stateflagSecStatus    	 	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 25}

		rsw200labelFactoryDefault           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Factory Default Reset  Digital parameter."
			   ::= { gx2Rsw200DigitalEntry 26}

		rsw200enumFactoryDefault               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object represents the Enumeration values
			    possible for the Digital parameter. Each Enumerated values is
			    separated by a common. The first value has a enumerated value of 1."
			   ::= { gx2Rsw200DigitalEntry 27}


		rsw200valueFactoryDefault         	OBJECT-TYPE
			   SYNTAX       		INTEGER {
							off(1),
							on(2)
					    		}
			   ACCESS           	read-write
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object is the current value of the parameter."
			   ::= { gx2Rsw200DigitalEntry 28}

		rsw200stateflagFactoryDefault     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200DigitalEntry 29}


		--*********** STATUS *****************
		gx2Rsw200StatusTableIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object identifies the network
			    element. This index is equal to the
			    hfcCommonTableIndex for the same element."
			   ::= { gx2Rsw200StatusEntry 1}

--New Parameter
		rsw200labelBoot               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Boot Status  Status parameter."
			   ::= { gx2Rsw200StatusEntry 2}

		rsw200valueBoot              		OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 3}

		rsw200stateflagBoot     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  4}



--New Parameter
		rsw200labelFlash               	OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Flash Status  Status parameter."
			   ::= { gx2Rsw200StatusEntry 5}

		rsw200valueFlash              	OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 6}

		rsw200stateflagFlash     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  7}

--New Parameter
		rsw200labelFactoryDataCRC           OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Factory Data CRC Status parameter."
			   ::= { gx2Rsw200StatusEntry 8}

		rsw200valueFactoryDataCRC          	OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 9}

		rsw200stateflagFactoryDataCRC     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  10}

--New Parameter
		rsw200labelAlarmDataCrc               	      OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Alarm Data Crc parameter."
			   ::= { gx2Rsw200StatusEntry 11}

		rsw200valueAlarmDataCrc              		OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 12}

		rsw200stateflagAlarmDataCrc     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  13}

--New Parameter
		rsw200labelRFSignalStatus              OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    RF Signal Status parameter."
			   ::= { gx2Rsw200StatusEntry 14}

		rsw200valueRFSignalStatus              OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 15}

		rsw200stateflagRFSignalStatus     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  16}

--New Parameter
		rsw200labelPriActiveStatus              OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))         
			   ACCESS           	read-only
			   STATUS           	optional
			   DESCRIPTION
			   "The value of this object provides the label of the
			    Secondary Active Status parameter."
			   ::= { gx2Rsw200StatusEntry 17}

		rsw200valuePriActiveStatus              OBJECT-TYPE
			   SYNTAX       		INTEGER {
									ok(1),
									undetermined(2),
									warning(3),
									minor(4),
									major(5),
									critical(6)
									}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the current state of
			    the parameter (0-Ok, 1-Undetermined
			    2-Warning, 3-Minor, 4-Major, 5-Critical)."
			   ::= { gx2Rsw200StatusEntry 18}

		rsw200stateflagPriActiveStatus     	OBJECT-TYPE
			   SYNTAX       		INTEGER {
								hidden(1),
								read-only(2),
								updateable(3)
								}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides the state
			    of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)."
			   ::= { gx2Rsw200StatusEntry  19}

            -- ************ FACTORY DATA ****************
		gx2Rsw200FactoryTableIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object identifies the network
			    element. This index is equal to the
			    hfcCommonTableIndex for the same element."
			   ::= { gx2Rsw200FactoryEntry 1}

		rsw200bootControlByte          	OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object indicates which bank the firmware
			    is currently being boot from."
			   ::= { gx2Rsw200FactoryEntry 2}

		rsw200bootStatusByte          	OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object indicates the status of the last boot"
			   ::= { gx2Rsw200FactoryEntry 3}

		rsw200bank1CRC          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the CRC code of bank 0."
			   ::= { gx2Rsw200FactoryEntry 4}

		rsw200bank2CRC          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the CRC code of bank 1."
			   ::= { gx2Rsw200FactoryEntry 5}

		rsw200prgEEPROMByte          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object indicates if the EEPROM has been programmed"
			   ::= { gx2Rsw200FactoryEntry 6}

		rsw200factoryCRC          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the CRC code for the Factory data."
			   ::= { gx2Rsw200FactoryEntry 7}

		rsw200calculateCRC          		OBJECT-TYPE
			   SYNTAX       		INTEGER {
							factory(1),
							alarm(2),
							na(3)
					    		}
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object indicates which of the Emnums will have the CRC calculated."
			   ::= { gx2Rsw200FactoryEntry 8}

		rsw200hourMeter          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the hour meter reading of the module."
			   ::= { gx2Rsw200FactoryEntry 9}

		rsw200flashPrgCntA          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the number of times Bank 1 flash has been 
                      programmed."
			   ::= { gx2Rsw200FactoryEntry 10}

		rsw200flashPrgCntB          		OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the number of times Bank 1 flash has been 
                      programmed."
			   ::= { gx2Rsw200FactoryEntry 11}

		rsw200flashBankARev          		OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the revision of flash bank 0."
			   ::= { gx2Rsw200FactoryEntry 12}

		rsw200flashBankBRev          		OBJECT-TYPE
			   SYNTAX       		DisplayString (SIZE (0..80))
			   ACCESS           	read-only
			   STATUS           	mandatory
			   DESCRIPTION
			   "This object provides the revision of flash bank 1."
			   ::= { gx2Rsw200FactoryEntry 13}

            -- ************ Hold Time DATA ****************
		rxgx2Rsw200bHoldTimeTableIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object is the index of the data object."
			   ::= { gx2Rsw200bHoldTimeEntry 1}

		rxgx2Rsw200bHoldTimeSpecIndex              OBJECT-TYPE
			   SYNTAX           INTEGER (1..4294967295)
			   ACCESS           read-only
			   STATUS           mandatory
			   DESCRIPTION
			   "The value of this object identifies the index of the alarm object to be modified."
			   ::= { gx2Rsw200bHoldTimeEntry 2}

		rxgx2Rsw200bHoldTimeData          	OBJECT-TYPE
			   SYNTAX       		INTEGER
			   ACCESS           	read-write
			   STATUS           	mandatory
			   DESCRIPTION
			   "The value of this object provides access to the hold timers used 
			   to suppress nose on analog objects. This object is a 32 bit object. 
			   Validation data is entered into bytes zero and one of the object. 
			   Bytes three and four are used to entering the hold time for the 
			   specified alarm object. The Hold timer data ranges from 0 to 1300 seconds.
			   The index of this object corresponds to the alarm object to be modified. 
			   Alarm Hold timers correspond to the index of this object as follows:  
			   Index 1 = xxx, index 2 = xxxx, Index 3 = xxxx, 
			   The hold time is represented in seconds."
			   ::= { gx2Rsw200bHoldTimeEntry 3}

-- ****************************************************************
--
-- TRAP DEFINITIONS
--
--
-- Every trap generated by an HFC agents will include first 9 identical
-- fields. If particular variable is not supported in
-- particular TRAP-TYPE then default value will be returned.
--
-- DESCRIPTION will include explanation of use of generic
-- variables (trapAdditionalInfo******.)  If no
-- DESCRIPTION is given then generic variables will contain
-- default values.
--
-- *****************************************************************

--***************************************************************************
-- ***********!!! THE TRAP SECTION HAS NOT BEEN COMPLETED YET !!! ***********
--***************************************************************************

-- **************************************************************************
--                              RF Switch Module traps
-- **************************************************************************
   trapRSW200ConfigChangeInteger TRAP-TYPE
       ENTERPRISE gx2Rsw200
       VARIABLES
	       {       
		trapIdentifier,
		trapNetworkElemModelNumber,
		trapNetworkElemSerialNum,
		trapPerceivedSeverity,
		trapNetworkElemOperState,
		trapNetworkElemAlarmStatus,  
		trapNetworkElemAdminState,
		trapNetworkElemAvailStatus,
		trapText,
		trapChangedObjectId,
		trapChangedValueInteger,
		trapNETrapLastTrapTimeStamp
	       }
       DESCRIPTION
	"This trap is issued if configuration of a single variable
	 with integer type was changed (via ANY interface).  
	 TrapChangedValueInteger variable may contain current reading
	 of that variable.
	 trapPerceivedSeverity - 'indeterminate'"
  ::= 1

   trapRSW200ConfigChangeDisplayString TRAP-TYPE
       ENTERPRISE gx2Rsw200
       VARIABLES
	       {       
		trapIdentifier,
		trapNetworkElemModelNumber,
		trapNetworkElemSerialNum,
		trapPerceivedSeverity,
		trapNetworkElemOperState,
		trapNetworkElemAlarmStatus,  
		trapNetworkElemAdminState,
		trapNetworkElemAvailStatus,
		trapText,
		trapChangedObjectId,
		trapChangedValueDisplayString,
		trapNETrapLastTrapTimeStamp
	       }
       DESCRIPTION
	"This trap is issued if configuration of a single variable
	 with DispalayString type was changed (via ANY interface).  
	 TrapChangedValueDisplayString variable may contain current reading
	 of that variable.
	 trapPerceivedSeverity - 'indeterminate'"
  ::= 2

  trapRSW200RFInputAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Switch Control signals 
	 go out of range.
	 trapAdditionalInfoInteger variable contains current reading of 
	 the this parameter."
  ::= 3
  
  trapRSW200FanCurrentAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Fan Current 
	 parameter goes out of range.
	 trapAdditionalInfoInteger variable contains current reading of 
	 the this parameter."
  ::= 4

  trapRSW200ModuleTempAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Temperature goes out of range.
	 trapAdditionalInfoInteger variable contains current reading of 
	 the this parameter."
  ::= 5

  trapRSW200FlashAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the detects an error during
	Flash memory operations."
  ::= 6

  trapRSW200BankBootAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the detects an error while booting
	from bank 0 or bank 1."
  ::= 7

	trapRSW200AlarmDataCRCAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Alarm Data CRC is incorrect."
  ::= 8

	trapRSW200FactoryDataCRCAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Factory Data CRC is incorrect."
  ::= 9

	trapRSW200InputSwitchedAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the RF input switched."
  ::= 10

	trapRSW200ResetFactoryDefaultAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the Factory Default Reset occurs."
  ::= 11

	trapRSW200SecondaryInputActiveAlarm TRAP-TYPE
	ENTERPRISE gx2Rsw200
	VARIABLES
		{       
		 trapIdentifier,
		 trapNetworkElemModelNumber,
		 trapNetworkElemSerialNum,
		 trapPerceivedSeverity,
		 trapNetworkElemOperState,
		 trapNetworkElemAlarmStatus,  
		 trapNetworkElemAdminState,
		 trapNetworkElemAvailStatus,
		 trapText,
		 trapChangedObjectId,
		 trapChangedValueInteger,
		 trapNETrapLastTrapTimeStamp
		}
	DESCRIPTION
	"This trap is issued when the scondary input becomes active."
  ::= 12

  END