OMNI-gx2CM-MIB DEFINITIONS ::= BEGIN IMPORTS Counter FROM RFC1155-SMI IpAddress, TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 sysUpTime, DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215 gi, motproxies FROM NLS-BBNIDENT-MIB gx2Cm FROM GX2HFC-MIB trapIdentifier,trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapNETrapLastTrapTimeStamp, trapChangedObjectId, trapChangedValueInteger, trapChangedValueDisplayString FROM NLSBBN-TRAPS-MIB; -- This MIB module uses the extended OBJECT-TYPE macro as -- defined in RFC1212 and the TRAP-TYPE macro as defined -- in RFC 1215. --REVISION "2" Jan 20, 2003 --DESCRIPTION -- Added revision and description comment section --REVISION "2" Jan 20, 2003 --DESCRIPTION -- Added parameter autoQuickSwapCnt to the quick swap table -- GX2 Control Module MIB MODULE -- This MIB module defines information for management of HFC networks -- -- The MIB module assumes that all generic (static) network element -- information is defined in a different module such as the HFC module -- The MIB consists of two groups: -- the device type descriptor subgroup and -- gx2Cm Network Elements subgroup. -- The device type descriptor subgroup is used to define -- parameters specific to gx2Cm device type. -- These parameters are common across all network elements -- from gx2Cm device type. -- -- The gx2Cm Network Elements subgroup is -- a list of gx2Cm type elements in the -- current network topology with nominal -- and current parameter values for the -- individual network elements; the individual -- network elements are identified by -- index from hfcCommonTable. -- That implies what hfcCommonTableIndex and -- gx2CmTableIndex are equal for each individual -- network element. -- This table is an extension of the hfcCommonTable -- for all elements of gx2Cm type. -- -- Both groups are mandatory for management of gx2Cm devices. -- **************************************************************************** -- -- All floating point numbers will be represented by an IEEE 32 Bit number. -- Conversion of this number must be done on the user interface to view the -- actual floating point number. -- Float ::= Counter -- UNSIGNED (32 BITS) -- **************************************************************************** -- gx2Cm Device Descriptor subgroup. -- The device type descriptor subgroup is used to define -- parameters specific to gx2Cm device type. -- These parameters are common across all network elements -- from gx2Cm device type. gx2cmDescriptor OBJECT IDENTIFIER ::= {gx2Cm 1} --***************************************************************************** -- gx2Cm Table -- Contains a list of all gx2Cm type devices in -- the network. Each device is characterized with -- current network topology information, with nominal -- and current parameter values for the -- individual network elements; -- -- The individual network elements indentified by -- index from hfcCommonTable. -- That implies what hfcCommonTableIndex and -- gx2cmTableIndex are equal for each individual -- nettwork element. -- This table should be used as an extension of the hfcCommonTable -- for all elements of gx2Cm type. --******************************************************************* gx2cmFactoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmFactoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 2 } gx2cmFactoryEntry OBJECT-TYPE SYNTAX Gx2cmFactoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Factory data and the associated parameter descriptions." INDEX { gx2cmFactoryTableIndex } ::= { gx2cmFactoryTable 1} --******************************************************************* gx2cmNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmNetworkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 3 } gx2cmNetworkEntry OBJECT-TYPE SYNTAX Gx2cmNetworkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Network parameters and the associated parameter descriptions." INDEX { gx2cmNetworkTableIndex } ::= { gx2cmNetworkTable 2} --******************************************************************* gx2cmAnalogTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmAnalogEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 4 } gx2cmAnalogEntry OBJECT-TYPE SYNTAX Gx2cmAnalogEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains analog parameters and the associated parameter descriptions." INDEX { gx2cmTableIndex } ::= { gx2cmAnalogTable 3} --******************************************************************* gx2cmDigitalTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmDigitalEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 5 } gx2cmDigitalEntry OBJECT-TYPE SYNTAX Gx2cmDigitalEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains digital parameters and the associated parameter descriptions." INDEX { gx2cmDigitalTableIndex } ::= { gx2cmDigitalTable 4} --******************************************************************* gx2cmStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 6 } gx2cmStatusEntry OBJECT-TYPE SYNTAX Gx2cmStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains status parameters and the associated parameter descriptions." INDEX { gx2cmStatusTableIndex } ::= { gx2cmStatusTable 5} --******************************************************************* gx2cmAMCTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmAMCEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 7 } gx2cmAMCEntry OBJECT-TYPE SYNTAX Gx2cmAMCEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains the AMC parameters and the associated parameter descriptions." INDEX { gx2cmAMCTableIndex } ::= { gx2cmAMCTable 6} --******************************************************************* gx2cmSecurityTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmSecurityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 8} gx2cmSecurityEntry OBJECT-TYPE SYNTAX Gx2cmSecurityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Security parameters and the associated parameter descriptions." INDEX { gx2cmSecurityTableIndex } ::= { gx2cmSecurityTable 7} --******************************************************************* gx2cmDiagnosticTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmDiagnosticEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 9} gx2cmDiagnosticEntry OBJECT-TYPE SYNTAX Gx2cmDiagnosticEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Diagnostic parameters and the associated parameter descriptions." INDEX { gx2cmDiagnosticTableIndex } ::= { gx2cmDiagnosticTable 8} --******************************************************************* gx2cmDownloadTable OBJECT-TYPE SYNTAX SEQUENCE OF Gx2cmDownloadEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains gx2Cm specific parameters with nominal and current values." ::= { gx2Cm 10} gx2cmDownloadEntry OBJECT-TYPE SYNTAX Gx2cmDownloadEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Download parameters and the associated parameter descriptions." INDEX { gx2cmDownloadTableIndex } ::= { gx2cmDownloadTable 9} --******************** Trap History Table ******************************** cmTrapHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CmTrapHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the trap specific parameters." ::= { gx2Cm 11} cmTrapHistoryEntry OBJECT-TYPE SYNTAX CmTrapHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This list contains Trap History parameters and the associated parameter descriptions." INDEX { cmTrapHistoryTableIndex } ::= { cmTrapHistoryTable 10} --**************************************************************************** Gx2cmAnalogEntry ::= SEQUENCE { gx2cmTableIndex INTEGER, -- Analog Parameters labelModTemp DisplayString (SIZE (0..80)), uomModTemp DisplayString (SIZE (0..80)), majorHighModTemp Float, majorLowModTemp Float, minorHighModTemp Float, minorLowModTemp Float, currentValueModTemp Float, stateFlagModTemp INTEGER, minValueModTemp Float, maxValueModTemp Float, alarmStateModTemp INTEGER } -- **************** Digital Parameters *********************** Gx2cmDigitalEntry ::= SEQUENCE { gx2cmDigitalTableIndex INTEGER, labelRemoteLocal DisplayString (SIZE (0..80)), enumRemoteLocal DisplayString (SIZE (0..80)), valueRemoteLocal INTEGER, stateFlagRemoteLocal INTEGER, labelResetSlot DisplayString (SIZE (0..80)), enumResetSlot DisplayString (SIZE (0..80)), valueResetSlot INTEGER, stateResetSlot INTEGER, labelIdShelf DisplayString (SIZE (0..80)), enumIdShelf DisplayString (SIZE (0..80)), valueIdShelf INTEGER, stateFlagIdShelf INTEGER, labelResetAlarm DisplayString (SIZE (0..80)), enumResetAlarm DisplayString (SIZE (0..80)), valueResetAlarm INTEGER, stateFlagResetAlarm INTEGER } -- **************** Status Parameters ************************************ Gx2cmStatusEntry ::= SEQUENCE { gx2cmStatusTableIndex INTEGER, labelShelfAlarm DisplayString (SIZE (0..80)), valueShelfAlarm INTEGER, stateShelfAlarm INTEGER, labelDataCrc DisplayString (SIZE (0..80)), valueDataCrc INTEGER, stateDataCrc INTEGER, labelFlashStatus DisplayString (SIZE (0..80)), valueFlashStatus INTEGER, stateFlashStatus INTEGER, labelBootStatus DisplayString (SIZE (0..80)), valueBootStatus INTEGER, stateBootStatus INTEGER, labelAlmLimCrc DisplayString (SIZE (0..80)), valueAlmLimCrc INTEGER, stateAlmLimCrc INTEGER } -- **************** Factory Parameters ************************************* Gx2cmFactoryEntry ::= SEQUENCE { gx2cmFactoryTableIndex INTEGER, bootControlByte INTEGER, bootStatusByte INTEGER, bank0CRC INTEGER, bank1CRC INTEGER, prgEEPROMByte INTEGER, factoryCRC INTEGER, calculateCRC INTEGER, hourMeter INTEGER, flashPrgCnt0 INTEGER, flashPrgCnt1 INTEGER, flashBank0 DisplayString (SIZE (0..80)), flashBank1 DisplayString (SIZE (0..80)), localMacAdd DisplayString (SIZE (0..80)), netWorkMacAdd DisplayString (SIZE (0..80)) } -- ************** Network info Parameters **************************** Gx2cmNetworkEntry ::= SEQUENCE { gx2cmNetworkTableIndex INTEGER, labelLocalEthIPAdd DisplayString (SIZE (0..80)), valueLocalEthIPAdd DisplayString (SIZE (0..80)), labelLocalEthMask DisplayString (SIZE (0..80)), valueLocalEthMask DisplayString (SIZE (0..80)), labelNetworkEthAdd DisplayString (SIZE (0..80)), valueNetworkEthAdd DisplayString (SIZE (0..80)), labelNetworkEthMask DisplayString (SIZE (0..80)), valueNetworkEthMask DisplayString (SIZE (0..80)), labelShelfSerialNum DisplayString (SIZE (0..80)), valueShelfSerialNum DisplayString (SIZE (0..80)), labelGateWayIPAdd DisplayString (SIZE (0..80)), valueGateWayIPAdd DisplayString (SIZE (0..80)), labelTrapDestination DisplayString (SIZE (0..80)), valueTrapDestination DisplayString (SIZE (0..80)), labelTFTPserver DisplayString (SIZE (0..80)), valueTFTPserver DisplayString (SIZE (0..80)), labelTrap2Destination DisplayString (SIZE (0..80)), valueTrap2Destination DisplayString (SIZE (0..80)), labelTrap3Destination DisplayString (SIZE (0..80)), valueTrap3Destination DisplayString (SIZE (0..80)), labelTrap4Destination DisplayString (SIZE (0..80)), valueTrap4Destination DisplayString (SIZE (0..80)), labelTrap5Destination DisplayString (SIZE (0..80)), valueTrap5Destination DisplayString (SIZE (0..80)), -- ISDN parameters Rev k labelISDNMode DisplayString (SIZE (0..80)), valueISDNMode INTEGER, labelISDNModemIPAddress DisplayString (SIZE (0..80)), valueISDNModemIPAddress DisplayString (SIZE (0..80)), labelISDNTrapTimeout DisplayString (SIZE (0..80)), valueISDNTrapTimeout INTEGER, labelISDNPingTimeout DisplayString (SIZE (0..80)), valueISDNPingTimeout INTEGER, labelISDNBackoffTimer DisplayString (SIZE (0..80)), valueISDNBackoffTimer INTEGER } -- ************** AMC Parameters **************************** Gx2cmAMCEntry ::= SEQUENCE { gx2cmAMCTableIndex INTEGER, valueAMCslot1 INTEGER, serialAMCslot1 DisplayString (SIZE (0..80)), agentIDAMCslot1 INTEGER, valueAMCslot2 INTEGER, serialAMCslot2 DisplayString (SIZE (0..80)), agentIDAMCslot2 INTEGER, valueAMCslot3 INTEGER, serialAMCslot3 DisplayString (SIZE (0..80)), agentIDAMCslot3 INTEGER, valueAMCslot4 INTEGER, serialAMCslot4 DisplayString (SIZE (0..80)), agentIDAMCslot4 INTEGER, valueAMCslot5 INTEGER, serialAMCslot5 DisplayString (SIZE (0..80)), agentIDAMCslot5 INTEGER, valueAMCslot6 INTEGER, serialAMCslot6 DisplayString (SIZE (0..80)), agentIDAMCslot6 INTEGER, valueAMCslot7 INTEGER, serialAMCslot7 DisplayString (SIZE (0..80)), agentIDAMCslot7 INTEGER, valueAMCslot8 INTEGER, serialAMCslot8 DisplayString (SIZE (0..80)), agentIDAMCslot8 INTEGER, valueAMCslot9 INTEGER, serialAMCslot9 DisplayString (SIZE (0..80)), agentIDAMCslot9 INTEGER, valueAMCslot10 INTEGER, serialAMCslot10 DisplayString (SIZE (0..80)), agentIDAMCslot10 INTEGER, valueAMCslot11 INTEGER, serialAMCslot11 DisplayString (SIZE (0..80)), agentIDAMCslot11 INTEGER, valueAMCslot12 INTEGER, serialAMCslot12 DisplayString (SIZE (0..80)), agentIDAMCslot12 INTEGER, valueAMCslot13 INTEGER, serialAMCslot13 DisplayString (SIZE (0..80)), agentIDAMCslot13 INTEGER, valueAMCslot14 INTEGER, serialAMCslot14 DisplayString (SIZE (0..80)), agentIDAMCslot14 INTEGER, valueAMCslot15 INTEGER, serialAMCslot15 DisplayString (SIZE (0..80)), agentIDAMCslot15 INTEGER, valueAMCslot16 INTEGER, serialAMCslot16 DisplayString (SIZE (0..80)), agentIDAMCslot16 INTEGER, valueAMCslot17 INTEGER, serialAMCslot17 DisplayString (SIZE (0..80)), agentIDAMCslot17 INTEGER, valueAMCslot18 INTEGER, serialAMCslot18 DisplayString (SIZE (0..80)), agentIDAMCslot18 INTEGER, autoQuickSwapCnt INTEGER } -- ************** Security Parameters **************************** Gx2cmSecurityEntry ::= SEQUENCE { gx2cmSecurityTableIndex INTEGER, labelSecurityMode DisplayString (SIZE (0..80)), enumSecurityMode DisplayString (SIZE (0..80)), valueSecurityMode INTEGER, stateSecurityMode INTEGER, labelPassword DisplayString (SIZE (0..80)), valuePassword DisplayString (SIZE (0..80)), statePassword INTEGER, labelFactoryChgString DisplayString (SIZE (0..80)), valueFactoryChgString DisplayString (SIZE (0..80)), stateFactoryChgString INTEGER, labelOperatorChgString DisplayString (SIZE (0..80)), valueOperatorChgString DisplayString (SIZE (0..80)), stateOperatorChgString INTEGER, labelReadOnlyChgString DisplayString (SIZE (0..80)), valueReadOnlyChgString DisplayString (SIZE (0..80)), stateReadOnlyChgString INTEGER, labelRemoteOnlyChgString DisplayString (SIZE (0..80)), valueRemoteOnlyChgString DisplayString (SIZE (0..80)), stateRemoteOnlyChgString INTEGER, labelLocalOnlyChgString DisplayString (SIZE (0..80)), valueLocalOnlyChgString DisplayString (SIZE (0..80)), stateLocalOnlyChgString INTEGER } --****************** Diagnostic Parameters ******************************** Gx2cmDiagnosticEntry ::= SEQUENCE { gx2cmDiagnosticTableIndex INTEGER, ledTestValue INTEGER, bpTestCnt INTEGER, successTransSlot1 INTEGER, successTransSlot2 INTEGER, successTransSlot3 INTEGER, successTransSlot4 INTEGER, successTransSlot5 INTEGER, successTransSlot6 INTEGER, successTransSlot7 INTEGER, successTransSlot8 INTEGER, successTransSlot9 INTEGER, successTransSlot10 INTEGER, successTransSlot11 INTEGER, successTransSlot12 INTEGER, successTransSlot13 INTEGER, successTransSlot14 INTEGER, successTransSlot15 INTEGER, successTransSlot16 INTEGER, successTransSlot17 INTEGER, successTransSlot18 INTEGER, failureTransSlot1 INTEGER, failureTransSlot2 INTEGER, failureTransSlot3 INTEGER, failureTransSlot4 INTEGER, failureTransSlot5 INTEGER, failureTransSlot6 INTEGER, failureTransSlot7 INTEGER, failureTransSlot8 INTEGER, failureTransSlot9 INTEGER, failureTransSlot10 INTEGER, failureTransSlot11 INTEGER, failureTransSlot12 INTEGER, failureTransSlot13 INTEGER, failureTransSlot14 INTEGER, failureTransSlot15 INTEGER, failureTransSlot16 INTEGER, failureTransSlot17 INTEGER, failureTransSlot18 INTEGER, fanTestMode INTEGER, fanControl INTEGER, relayTestMode INTEGER, relayControl INTEGER, slotPollMode INTEGER, bootCount INTEGER, objectTableData DisplayString (SIZE (0..80)), setSysTime INTEGER } --****************** Download Parameters ******************************** Gx2cmDownloadEntry ::= SEQUENCE { gx2cmDownloadTableIndex INTEGER, downloadValue INTEGER, autoDownloadReset INTEGER, downloadFilename DisplayString (SIZE (0..80)), downloadState INTEGER, switchFwBank INTEGER } --****************** Trap History Parameters ******************************** CmTrapHistoryEntry ::= SEQUENCE { cmTrapHistoryTableIndex INTEGER, netrapId INTEGER, netrapNetworkElemModelNumber DisplayString (SIZE (0..80)), netrapNetworkElemSerialNum DisplayString (SIZE (0..80)), netrapPerceivedSeverity INTEGER, netrapNetworkElemOperState INTEGER, netrapNetworkElemAlarmStatus INTEGER, netrapNetworkElemAdminState INTEGER, netrapNetworkElemAvailStatus INTEGER, netrapText DisplayString (SIZE (0..80)), netrapLastTrapTimeStamp TimeTicks, netrapChangedObjectId DisplayString (SIZE (0..80)), netrapAdditionalInfoInteger1 INTEGER, netrapAdditionalInfoInteger2 INTEGER, netrapAdditionalInfoInteger3 INTEGER, netrapChangedValueDisplayString DisplayString (SIZE (0..80)), netrapChangedValueOID DisplayString (SIZE (0..80)), netrapChangedValueIpAddress INTEGER, netrapChangedValueInteger INTEGER } -- ************** Analog Parameters **************************** gx2cmTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmAnalogEntry 1} -- New Parameter labelModTemp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Module Temp parameter." ::= { gx2cmAnalogEntry 2} uomModTemp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the Unit of Measure of the Module Temp parameter." ::= { gx2cmAnalogEntry 3} majorHighModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the Major High alarm value of the Module Temp parameter." ::= { gx2cmAnalogEntry 4} majorLowModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the Major Low alarm value of the Module Temp parameter." ::= { gx2cmAnalogEntry 5} minorHighModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the Minor High alarm value of the Module Temp parameter." ::= { gx2cmAnalogEntry 6} minorLowModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the Minor Low alarm value of the Module Temp parameter." ::= { gx2cmAnalogEntry 7} currentValueModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the Current value of the Module Temp parameter." ::= { gx2cmAnalogEntry 8} stateFlagModTemp OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the state of the Module Temp parameter. (0-Hidden 1-Read-Only, 2-Updateable)" ::= { gx2cmAnalogEntry 9} minValueModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the minimum value the Module Temp parameter can achive." ::= { gx2cmAnalogEntry 10} maxValueModTemp OBJECT-TYPE SYNTAX Float ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the maximum value the Module Temp parameter can achive." ::= { gx2cmAnalogEntry 11} alarmStateModTemp OBJECT-TYPE SYNTAX INTEGER { noAlarm(1), majorLowAlarm(2), minorLowAlarm(3), minorHighAlarm(4), majorHighAlarm(5), informational(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the curent alarm state of the Module Temp Analog parameter." ::= { gx2cmAnalogEntry 12} -- ************************ Digital parameters ********************************** gx2cmDigitalTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmDigitalEntry 1} -- New parameter labelRemoteLocal OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS obsolete DESCRIPTION "The value of this object provides the label of the Remote Local Control Digital parameter." ::= { gx2cmDigitalEntry 2} enumRemoteLocal OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS obsolete DESCRIPTION "The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated value is separated by a common. The first value has a enumerated value of 1." ::= { gx2cmDigitalEntry 3} valueRemoteLocal OBJECT-TYPE SYNTAX INTEGER { local(1), remote(2) } ACCESS read-write STATUS obsolete DESCRIPTION "The value of this object is the current value of the parameter." ::= { gx2cmDigitalEntry 4} stateFlagRemoteLocal OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS obsolete DESCRIPTION "The value of this object provides the state of the Remote Local Control Digital parameter. (0-Hidden 1-Read-Only, 2-Updateable)." ::= { gx2cmDigitalEntry 5} -- New parameter labelResetSlot OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Reset Slot Digital parameter." ::= { gx2cmDigitalEntry 6} enumResetSlot OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated value is separated by a common. The first value has a enumerated value of 1." ::= { gx2cmDigitalEntry 7} valueResetSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object is the current value of the parameter. A write to this object will casue a hardware reset. 0-control module 1-18 selected slot. " ::= { gx2cmDigitalEntry 8} stateResetSlot OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the state of the parameter. (0-Hidden 1-Read-Only, 2-Updateable)." ::= { gx2cmDigitalEntry 9} -- New parameter labelIdShelf OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the identify shelf Digital parameter." ::= { gx2cmDigitalEntry 10} enumIdShelf OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated value is separated by a common. The first value has a enumerated value of 1.." ::= { gx2cmDigitalEntry 11} valueIdShelf OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object is the current value of the parameter. Writing any non zero value to this parameter will casue the CM to blink its front panel LED." ::= { gx2cmDigitalEntry 12} stateFlagIdShelf OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)." ::= { gx2cmDigitalEntry 13} -- New parameter labelResetAlarm OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Reset Alarms Digital parameter." ::= { gx2cmDigitalEntry 14} enumResetAlarm OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object represents the Enumeration values possible for the Digital parameter. Each Enumerated value is separated by a common. The first value has a enumerated value of 1." ::= { gx2cmDigitalEntry 15} valueResetAlarm OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object is the current value of the parameter. Writing any non-zero value to this object will case the CM to reset shelf alarm processing." ::= { gx2cmDigitalEntry 16} stateFlagResetAlarm OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the state of the the parameter. (0-Hidden 1-Read-Only, 2-Updateable)." ::= { gx2cmDigitalEntry 17} --*********************** STATUS ************************************** gx2cmStatusTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmStatusEntry 1} --New Parameter labelShelfAlarm OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Shelf Alarm Status parameter." ::= { gx2cmStatusEntry 2} valueShelfAlarm OBJECT-TYPE SYNTAX INTEGER { ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current status of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical)." ::= { gx2cmStatusEntry 3} stateShelfAlarm OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current state of the parameter." ::= { gx2cmStatusEntry 4} --New Parameter labelDataCrc OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Data CRC parameter." ::= { gx2cmStatusEntry 5} valueDataCrc OBJECT-TYPE SYNTAX INTEGER { ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current status of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical)." ::= { gx2cmStatusEntry 6} stateDataCrc OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current state of the parameter." ::= { gx2cmStatusEntry 7} --New Parameter labelFlashStatus OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Flash Status parameter." ::= { gx2cmStatusEntry 8} valueFlashStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current status of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical)." ::= { gx2cmStatusEntry 9} stateFlashStatus OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current state of the parameter." ::= { gx2cmStatusEntry 10} --New Parameter labelBootStatus OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Boot Status parameter." ::= { gx2cmStatusEntry 11} valueBootStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current status of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical)." ::= { gx2cmStatusEntry 12} stateBootStatus OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current state of the parameter." ::= { gx2cmStatusEntry 13} --New Parameter labelAlmLimCrc OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object provides the label of the Alarm limit CRC parameter." ::= { gx2cmStatusEntry 14} valueAlmLimCrc OBJECT-TYPE SYNTAX INTEGER { ok(1), undetermined(2), warning(3), minor(4), major(5), critical(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current status of the parameter (0-Ok, 1-Undetermined 2-Warning, 3-Minor, 4-Major, 5-Critical)." ::= { gx2cmStatusEntry 15} stateAlmLimCrc OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object provides the current state of the parameter." ::= { gx2cmStatusEntry 16} -- ************ FACTORY DATA **************** gx2cmFactoryTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmFactoryEntry 1} bootControlByte OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object indicates which bank the firmware is currently being boot from." ::= { gx2cmFactoryEntry 2} bootStatusByte OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the status of the last boot" ::= { gx2cmFactoryEntry 3} bank0CRC OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the CRC code of bank 1." ::= { gx2cmFactoryEntry 4} bank1CRC OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the CRC code of bank 2." ::= { gx2cmFactoryEntry 5} prgEEPROMByte OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates if the EEPROM has been programmed" ::= { gx2cmFactoryEntry 6} factoryCRC OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the CRC code for the Factory data." ::= { gx2cmFactoryEntry 7} calculateCRC OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the CRC value of the fimware." ::= { gx2cmFactoryEntry 8} hourMeter OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the hour meter reading of the module." ::= { gx2cmFactoryEntry 9} flashPrgCnt0 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the number of times the flash has been programmed on side A." ::= { gx2cmFactoryEntry 10} flashPrgCnt1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the number of times the flash has been programmed on side B." ::= { gx2cmFactoryEntry 11} flashBank0 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the firmware revision of the firmware in bank 0." ::= { gx2cmFactoryEntry 12} flashBank1 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the firmware revision of the firmware in bank 1." ::= { gx2cmFactoryEntry 13} localMacAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the local mac address number" ::= { gx2cmFactoryEntry 14} netWorkMacAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the network mac address number." ::= { gx2cmFactoryEntry 15} -- ************** Network info Parameters ********************* gx2cmNetworkTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmNetworkEntry 1} labelLocalEthIPAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Ethernet IP Address field." ::= { gx2cmNetworkEntry 2} valueLocalEthIPAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the Local Ethernet IP Address for the Control Module." ::= { gx2cmNetworkEntry 3} -- labelLocalEthMask OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Local Ethernet Mask field." ::= { gx2cmNetworkEntry 4} valueLocalEthMask OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the Local Ethernet Mask value." ::= { gx2cmNetworkEntry 5} -- labelNetworkEthAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Network Ethernet Address ." ::= { gx2cmNetworkEntry 6} valueNetworkEthAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value of the Network Ethernet Address." ::= { gx2cmNetworkEntry 7} -- labelNetworkEthMask OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Network Mask Address." ::= { gx2cmNetworkEntry 8} valueNetworkEthMask OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value of the Network Mask Address." ::= { gx2cmNetworkEntry 9} -- labelShelfSerialNum OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Shelf Serial Number." ::= { gx2cmNetworkEntry 10} valueShelfSerialNum OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the value for the Shelf Serial Number." ::= { gx2cmNetworkEntry 11} labelGateWayIPAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Gateway IP address." ::= { gx2cmNetworkEntry 12} valueGateWayIPAdd OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the IP address for the Gateway." ::= { gx2cmNetworkEntry 13} labelTrapDestination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the trap destination field." ::= { gx2cmNetworkEntry 14} valueTrapDestination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the trap destination." ::= { gx2cmNetworkEntry 15} labelTFTPserver OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the TFTP Server address field." ::= { gx2cmNetworkEntry 16} valueTFTPserver OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the TFTP Server." ::= { gx2cmNetworkEntry 17} labelTrap2Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the second trap destination field." ::= { gx2cmNetworkEntry 18} valueTrap2Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the second trap destination." ::= { gx2cmNetworkEntry 19} labelTrap3Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the third trap destination field." ::= { gx2cmNetworkEntry 20} valueTrap3Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the third trap destination." ::= { gx2cmNetworkEntry 21} labelTrap4Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the fourth trap destination field." ::= { gx2cmNetworkEntry 22} valueTrap4Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the fourth trap destination." ::= { gx2cmNetworkEntry 23} labelTrap5Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label the fifth trap destination field." ::= { gx2cmNetworkEntry 24} valueTrap5Destination OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the address for the fifth trap destination." ::= { gx2cmNetworkEntry 25} -- ISDN parameters Rev k labelISDNMode OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the ISDN mode setting." ::= { gx2cmNetworkEntry 26} valueISDNMode OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the ISDN mode setting. In order to activate the ISDN feature, the user must set the ISDN mode to ON and provide a valid IP address. This address needs to be the IP address of the remote ISDN Modem." ::= { gx2cmNetworkEntry 27} labelISDNModemIPAddress OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the ISDN modem IP Address." ::= { gx2cmNetworkEntry 28} valueISDNModemIPAddress OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the ISDN modem IP Address. This Address is used by the control Module to ping the remote ISDN modem to determine if an ISDN connection is made. Only after a successful ping response to this address and the ISDN Modem Mode object is set to ON will the Control Module send traps. Factory default value is 0.0.0.0." ::= { gx2cmNetworkEntry 29} labelISDNTrapTimeout OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the ISDN modem Timeout object." ::= { gx2cmNetworkEntry 30} valueISDNTrapTimeout OBJECT-TYPE SYNTAX INTEGER (0 .. 3600) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the ISDN modem Timeout. The value of this object sets the time period that the communication link is open for sending traps. This timer is started when the first trap is issued. The factory default for this value is 2 minutes. Unit of measure is in seconds." ::= { gx2cmNetworkEntry 31} labelISDNPingTimeout OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the ISDN ping timeout object." ::= { gx2cmNetworkEntry 32} valueISDNPingTimeout OBJECT-TYPE SYNTAX INTEGER (100 .. 5000) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the ISDN ping timeout. Factory default value is 500 ms. User should set this value in milli-second" ::= { gx2cmNetworkEntry 33} labelISDNBackoffTimer OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the ISDN backoff timer object." ::= { gx2cmNetworkEntry 34} valueISDNBackoffTimer OBJECT-TYPE SYNTAX INTEGER (0 .. 3600) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the ISDN backoff timer. The value in this object is a hold period used to prevent traps from being sent. It is used to allow other chassis to have time to connect and communicate over the ISDN modems. This hold period starts after the valueISDNTrapTimeout period has expired. NOTE: The value of this object should be set to a value greater than the ISDN Modem's idle connection timeout period. This will allow the Modem to break the ISDN Connection. Factory default value is 2 min (120 sec). User should set this value in seconds" ::= { gx2cmNetworkEntry 35} --**************** Security Parameters******************** gx2cmSecurityTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmSecurityEntry 1} labelSecurityMode OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Current Security Mode." ::= { gx2cmSecurityEntry 2} enumSecurityMode OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "The value of this object represents the Enumeration values possible for the security mode parameter. Each Enumerated value is separated by a common. The first value has a enumerated value of 1." ::= { gx2cmSecurityEntry 3} valueSecurityMode OBJECT-TYPE SYNTAX INTEGER { read-only(1), operator-access(2), factory-access(3), remote-write-only(4), local-write-only(5) } ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the current Security Mode." ::= { gx2cmSecurityEntry 4} stateSecurityMode OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the state of the Security Mode parameter ." ::= { gx2cmSecurityEntry 5} labelPassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the label for the Password field." ::= { gx2cmSecurityEntry 6} valuePassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value for the Password." ::= { gx2cmSecurityEntry 7} statePassword OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the password field." ::= { gx2cmSecurityEntry 8} labelFactoryChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the lable for the Factory Change String field." ::= { gx2cmSecurityEntry 9} valueFactoryChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS write-only STATUS mandatory DESCRIPTION "This object provides the value for the Factory Change String." ::= { gx2cmSecurityEntry 10} stateFactoryChgString OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the Factory Change String field." ::= { gx2cmSecurityEntry 11} labelOperatorChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the lable for the Operator Change String field." ::= { gx2cmSecurityEntry 12} valueOperatorChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS write-only STATUS mandatory DESCRIPTION "This object provides the value for the Operator Change String." ::= { gx2cmSecurityEntry 13} stateOperatorChgString OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the Operator Change String field." ::= { gx2cmSecurityEntry 14} labelReadOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the lable for the Read Only Change String field." ::= { gx2cmSecurityEntry 15} valueReadOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS write-only STATUS mandatory DESCRIPTION "This object provides the value for the Read Only Change String." ::= { gx2cmSecurityEntry 16} stateReadOnlyChgString OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the Read Only Change String field." ::= { gx2cmSecurityEntry 17} labelRemoteOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the lable for the Remote Only Change String field." ::= { gx2cmSecurityEntry 18} valueRemoteOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS write-only STATUS mandatory DESCRIPTION "This object provides the value for the Remote Only Change String." ::= { gx2cmSecurityEntry 19} stateRemoteOnlyChgString OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the Remote Only Change String field." ::= { gx2cmSecurityEntry 20} labelLocalOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS optional DESCRIPTION "This object provides the lable for the Local Only Change String field." ::= { gx2cmSecurityEntry 21} valueLocalOnlyChgString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS write-only STATUS mandatory DESCRIPTION "This object provides the value for the Local Only Change String." ::= { gx2cmSecurityEntry 22} stateLocalOnlyChgString OBJECT-TYPE SYNTAX INTEGER { hidden(1), read-only(2), updateable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the state of the Local Only Change String field." ::= { gx2cmSecurityEntry 23} -- **************************AMC Parameters ******************************************** gx2cmAMCTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmAMCEntry 1} valueAMCslot1 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 2} serialAMCslot1 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 3} agentIDAMCslot1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 4} -- valueAMCslot2 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 5} serialAMCslot2 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 6} agentIDAMCslot2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 7} -- valueAMCslot3 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 8} serialAMCslot3 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 9} agentIDAMCslot3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 10} -- valueAMCslot4 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 11} serialAMCslot4 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 12} agentIDAMCslot4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 13} -- valueAMCslot5 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 14} serialAMCslot5 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 15} agentIDAMCslot5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 16} -- valueAMCslot6 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 17} serialAMCslot6 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 18} agentIDAMCslot6 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 19} -- valueAMCslot7 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 20} serialAMCslot7 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 21} agentIDAMCslot7 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 22} -- valueAMCslot8 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 23} serialAMCslot8 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 24} agentIDAMCslot8 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 25} -- valueAMCslot9 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 26} serialAMCslot9 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 27} agentIDAMCslot9 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 28} -- valueAMCslot10 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 29} serialAMCslot10 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 30} agentIDAMCslot10 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 31} -- valueAMCslot11 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 32} serialAMCslot11 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 33} agentIDAMCslot11 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 34} -- valueAMCslot12 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 35} serialAMCslot12 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 36} agentIDAMCslot12 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 37} -- valueAMCslot13 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 38} serialAMCslot13 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 39} agentIDAMCslot13 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 40} -- valueAMCslot14 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 41} serialAMCslot14 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 42} agentIDAMCslot14 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 43} -- valueAMCslot15 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 44} serialAMCslot15 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 45} agentIDAMCslot15 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 46} -- valueAMCslot16 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 47} serialAMCslot16 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 48} agentIDAMCslot16 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 49} -- valueAMCslot17 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 50} serialAMCslot17 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 51} agentIDAMCslot17 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 52} -- valueAMCslot18 OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), force(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control to enable or disable AMC for the current device in the slot." ::= { gx2cmAMCEntry 53} serialAMCslot18 OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the serial number for the AMC slot selected." ::= { gx2cmAMCEntry 54} agentIDAMCslot18 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the agentID of the AMC parameter for the selected slot." ::= { gx2cmAMCEntry 55} autoQuickSwapCnt OBJECT-TYPE SYNTAX INTEGER { timeroff(1), onehour(2), oneday(3), oneweek(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This object sets the time interval as to when the Control Module will update its memory with quick swap data. The Control Module will enable the quick swap feature for each module in the system. It will then retrieve the quick swap data from each module. The timer settings are as follows: 1=timeroff, 2=onehour, 3=oneday, 4=oneweek." ::= { gx2cmAMCEntry 56} --****************** Diagnostic Parameters ******************************** gx2cmDiagnosticTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmDiagnosticEntry 1} ledTestValue OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the LED test pattern on/off control." ::= { gx2cmDiagnosticEntry 2} bpTestCnt OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object control which slot the alarm poll command will be repeatedly sent to. During this operation normal polling is disabled. 0-off, 1-18 selects the slot." ::= { gx2cmDiagnosticEntry 3} successTransSlot1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 4} successTransSlot2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 5} successTransSlot3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 6} successTransSlot4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 7} successTransSlot5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 8} successTransSlot6 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 9} successTransSlot7 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 10} successTransSlot8 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 11} successTransSlot9 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 12} successTransSlot10 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 13} successTransSlot11 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 14} successTransSlot12 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 15} successTransSlot13 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 16} successTransSlot14 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 17} successTransSlot15 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 18} successTransSlot16 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 19} successTransSlot17 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 20} successTransSlot18 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot passes." ::= { gx2cmDiagnosticEntry 21} failureTransSlot1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 22} failureTransSlot2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 23} failureTransSlot3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 24} failureTransSlot4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 25} failureTransSlot5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 26} failureTransSlot6 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 27} failureTransSlot7 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 28} failureTransSlot8 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 29} failureTransSlot9 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 30} failureTransSlot10 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 31} failureTransSlot11 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 32} failureTransSlot12 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 33} failureTransSlot13 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 34} failureTransSlot14 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 35} failureTransSlot15 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 36} failureTransSlot16 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 37} failureTransSlot17 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 38} failureTransSlot18 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides data on the number of time writing to the selected slot fails." ::= { gx2cmDiagnosticEntry 39} fanTestMode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control for putting the fan in manual test mode. Writing any non-zero value will set to on" ::= { gx2cmDiagnosticEntry 40} fanControl OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control over the fan mode." ::= { gx2cmDiagnosticEntry 41} relayTestMode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control for putting the relay in manual test mode. Writing any non-zero value will set to on" ::= { gx2cmDiagnosticEntry 42} relayControl OBJECT-TYPE SYNTAX INTEGER { open(1), closed(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control for putting the relay in manual test mode." ::= { gx2cmDiagnosticEntry 43} slotPollMode OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object provides control of the slotpoll test mode. When on the slotpoll operation is disabled." ::= { gx2cmDiagnosticEntry 44} bootCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the value of how many times the CM went though a boot/rest process." ::= { gx2cmDiagnosticEntry 45} objectTableData OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This object provides the OID for the start loations for the status, digital and analog tables. This data is used by the web server application." ::= { gx2cmDiagnosticEntry 46} setSysTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Writing any value to this object will reset sysUpTime to zero." ::= { gx2cmDiagnosticEntry 47} --****************** Download Parameters ******************************** gx2cmDownloadTableIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object identifies the network element. This index is equal to the hfcCommonTableIndex for the same element." ::= { gx2cmDownloadEntry 1} downloadValue OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the slot(s) to be downloaded. The slots to be downloaded corresponds to the following bit map. bit 0 - control module, bits 1-18 to the corresponding slot. Any combination of bit may be set. If all bits are reset this will halt the download." ::= { gx2cmDownloadEntry 2} autoDownloadReset OBJECT-TYPE SYNTAX INTEGER { deactivate(1), activate(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object determines if the module will be reset directly after a successfull download. 0 - Deactivated, 1+ Activated" ::= { gx2cmDownloadEntry 3} downloadFilename OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the name of the file for download" ::= { gx2cmDownloadEntry 4} downloadState OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object provides the current state of the download process." ::= { gx2cmDownloadEntry 5} switchFwBank OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Writting to this object causes the firmware bank to switch and execute from that bank. The range of values that can be entered for this object is from 0 to 18. Where 0 is slot 0, and 18 is slot 18." ::= { gx2cmDownloadEntry 6} -- **************** Trap history table **************************** cmTrapHistoryTableIndex OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the trap issued by the network element." ::= { cmTrapHistoryEntry 1} netrapId OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this objest is the trap ID number provided by network element." ::= { cmTrapHistoryEntry 2} netrapNetworkElemModelNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object is the model number of the network element. Combination of Model # and Serial # is used as the unique identifier of the NE." ::= { cmTrapHistoryEntry 3} netrapNetworkElemSerialNum OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "The value of this object is the serial number of the network element." ::= { cmTrapHistoryEntry 4} netrapPerceivedSeverity OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This parameter defines five severity levels, which provide an indication of the perceived status of the managed object." ::= { cmTrapHistoryEntry 5} netrapNetworkElemOperState OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The current Operational State of the Network Element which generated the trap.." ::= { cmTrapHistoryEntry 6} netrapNetworkElemAlarmStatus OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The current Alarm Status of the Network Element. Alarm Status is always equal to the highest severity level of all outstanding alarms in this NE.." ::= { cmTrapHistoryEntry 7} netrapNetworkElemAdminState OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The current Adminsitrative state of the network element." ::= { cmTrapHistoryEntry 8} netrapNetworkElemAvailStatus OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The current Operational state of the network elment" ::= { cmTrapHistoryEntry 9} netrapText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This variable contains trap text." ::= { cmTrapHistoryEntry 10} netrapLastTrapTimeStamp OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This OBJECT IDENTIFIER is used to hold time when trap was generated." ::= { cmTrapHistoryEntry 11} netrapChangedObjectId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This variable identifies the object that has generated the trap." ::= { cmTrapHistoryEntry 12} netrapAdditionalInfoInteger1 OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This 32 bit integer is used to hold specific information about the trap." ::= { cmTrapHistoryEntry 13} netrapAdditionalInfoInteger2 OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "this 32 bit integer is used to hold specific information about the trap." ::= { cmTrapHistoryEntry 14} netrapAdditionalInfoInteger3 OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This 32 bit integer is used to hold specific information about the trap." ::= { cmTrapHistoryEntry 15} netrapChangedValueDisplayString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This DisplayString is used to hold specific information about the trap" ::= { cmTrapHistoryEntry 16} netrapChangedValueOID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) ACCESS read-only STATUS mandatory DESCRIPTION "This OBJECT IDENTIFIER is used to hold specific information about the trap" ::= { cmTrapHistoryEntry 17} netrapChangedValueIpAddress OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This OBJECT IDENTIFIER is used to hold specific information about the trap." ::= { cmTrapHistoryEntry 18} netrapChangedValueInteger OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "this 32 bit integer is used to hold the data value that this object has been changed too." ::= { cmTrapHistoryEntry 19} -- **************************************************************** -- -- TRAP DEFINITIONS -- -- -- Every trap generated by an HFC agents will include first 9 identical -- fields. If particular variable is not supported in -- particular TRAP-TYPE then default value will be returned. -- -- DESCRIPTION will include explanation of use of generic -- variables (trapAdditionalInfo******.) If no -- DESCRIPTION is given then generic variables will contain -- default values. -- -- ***************************************************************** --*************************************************************************** --*************************************************************************** -- ************************************************************************** -- Laser Module traps -- ************************************************************************** trapCMConfigChangeInteger TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued if configuration of a single variable with integer type was changed (via ANY interface). TrapChangedValueInteger variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'" ::= 1 trapCMConfigChangeDisplayString TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueDisplayString, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued if configuration of a single variable with DispalayString type was changed (via ANY interface). TrapChangedValueDisplayString variable may contain current reading of that variable. trapPerceivedSeverity - 'indeterminate'" ::= 2 trapCMModuleTempAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the Module Temperature parameter goes out of range. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 3 trapCMEEPROMAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the EEPROM detectes an error. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 4 trapCMFlashAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the Flash device detects an error. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 5 trapCMHardwareAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the system hardware detectes an error. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 6 trapCMInitEEPROMAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the there is an EEPROM initializing error. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 7 trapCMBootAlarm TRAP-TYPE ENTERPRISE gx2Cm VARIABLES { trapIdentifier, trapNetworkElemModelNumber, trapNetworkElemSerialNum, trapPerceivedSeverity, trapNetworkElemOperState, trapNetworkElemAlarmStatus, trapNetworkElemAdminState, trapNetworkElemAvailStatus, trapText, trapChangedObjectId, trapChangedValueInteger, trapNETrapLastTrapTimeStamp } DESCRIPTION "This trap is issued when the there is a boot error. trapAdditionalInfoInteger variable contains current reading of the this parameter." ::= 8 END