-- -- EXTREME-SUMMIT-WM-MIB.my -- MIB generated by MG-SOFT Visual MIB Builder Version 4.0 Build 349 -- Friday, October 28, 2005 at 15:11:28 -- EXTREME-SUMMIT-WM-MIB DEFINITIONS ::= BEGIN IMPORTS summitWMMgmt, summitWMModules FROM EXTREME-SUMMIT-WM-SMI WEPKeytype FROM IEEE802dot11-MIB ifIndex, InterfaceIndex FROM IF-MIB OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF TimeTicks, IpAddress, Integer32, Counter64, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString, TruthValue, RowStatus, MacAddress, TEXTUAL-CONVENTION FROM SNMPv2-TC; -- September 01, 2005 at 02:37 GMT -- September 01, 2005 at 02:37 GMT -- 1.3.6.1.4.1.1916.5.5.2 summitWMMIB MODULE-IDENTITY LAST-UPDATED "200510280311Z" -- October 28, 2005 at 03:11 GMT ORGANIZATION "Extreme Networks, Inc." CONTACT-INFO "www.extremenetworks.com" DESCRIPTION "Summit WM MIB definition" REVISION "200510280311Z" -- October 28, 2005 at 03:11 GMT DESCRIPTION "Initial revision." ::= { summitWMModules 2 } -- -- Textual conventions -- LogEventSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The log event severities used in the access controller." SYNTAX INTEGER { critical(1), major(2), minor(3), information(4), trace(5) } -- -- Node definitions -- -- 1.3.6.1.4.1.1916.5.3.2 summitWM OBJECT IDENTIFIER ::= { summitWMMgmt 2 } -- 1.3.6.1.4.1.1916.5.3.2.1 systemObjects OBJECT IDENTIFIER ::= { summitWM 1 } -- 1.3.6.1.4.1.1916.5.3.2.1.1 sysSoftwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "System software version." ::= { systemObjects 1 } -- 1.3.6.1.4.1.1916.5.3.2.1.2 sysLogLevel OBJECT-TYPE SYNTAX LogEventSeverity MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the level of events which are written to the system log." ::= { systemObjects 2 } -- 1.3.6.1.4.1.1916.5.3.2.1.3 sysSerialNo OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "System serial number." ::= { systemObjects 3 } -- 1.3.6.1.4.1.1916.5.3.2.1.4 sysLogSupport OBJECT IDENTIFIER ::= { systemObjects 4 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.1 summitWMAppLogFacility OBJECT-TYPE SYNTAX INTEGER { local0(0), local1(1), local2(2), local3(3), local4(4), local5(5), local6(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The application log facility level for syslog." ::= { sysLogSupport 1 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.2 serviceLogFacility OBJECT-TYPE SYNTAX INTEGER { local0(0), local1(1), local2(2), local3(3), local4(4), local5(5), local6(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The service log facility level for syslog." ::= { sysLogSupport 2 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.3 includeAllServiceMessages OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if DHCP messages should also be forwarded to syslog." ::= { sysLogSupport 3 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4 sysLogServersTable OBJECT-TYPE SYNTAX SEQUENCE OF SysLogServersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of syslog servers to forward logging messages." ::= { sysLogSupport 4 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1 sysLogServersEntry OBJECT-TYPE SYNTAX SysLogServersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for an external syslog server." INDEX { sysLogServerIndex } ::= { sysLogServersTable 1 } SysLogServersEntry ::= SEQUENCE { sysLogServerIndex Integer32, sysLogServerEnabled TruthValue, sysLogServerIP IpAddress, sysLogServerPort Integer32, sysLogServerRowStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1.1 sysLogServerIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Table index for the syslog server." ::= { sysLogServersEntry 1 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1.2 sysLogServerEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if messages are to be sent to the syslog server." ::= { sysLogServersEntry 2 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1.3 sysLogServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "syslog server IP address." ::= { sysLogServersEntry 3 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1.4 sysLogServerPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "syslog server port number." ::= { sysLogServersEntry 4 } -- 1.3.6.1.4.1.1916.5.3.2.1.4.4.1.5 sysLogServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus for operating on syslogServersTable." ::= { sysLogServersEntry 5 } -- 1.3.6.1.4.1.1916.5.3.2.3 mgmtPortObjects OBJECT IDENTIFIER ::= { summitWM 3 } -- 1.3.6.1.4.1.1916.5.3.2.3.1 mgmtPortIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "ifIndex of the management port." ::= { mgmtPortObjects 1 } -- 1.3.6.1.4.1.1916.5.3.2.3.2 mgmtPortHostname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Hostname of the management port." ::= { mgmtPortObjects 2 } -- 1.3.6.1.4.1.1916.5.3.2.3.3 mgmtPortPrimaryDNS OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Primary domain server for the management port." ::= { mgmtPortObjects 3 } -- 1.3.6.1.4.1.1916.5.3.2.3.4 mgmtPortSecondaryDNS OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Secondary domain server for the management port." ::= { mgmtPortObjects 4 } -- 1.3.6.1.4.1.1916.5.3.2.3.5 mgmtPortDomain OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Domain of the management port." ::= { mgmtPortObjects 5 } -- 1.3.6.1.4.1.1916.5.3.2.4 physicalPortObjects OBJECT IDENTIFIER ::= { summitWM 4 } -- 1.3.6.1.4.1.1916.5.3.2.4.1 physicalPortCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of rows in routerPortsTable." ::= { physicalPortObjects 1 } -- 1.3.6.1.4.1.1916.5.3.2.4.2 physicalPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF PhysicalPortsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of router ports on the controller." ::= { physicalPortObjects 2 } -- 1.3.6.1.4.1.1916.5.3.2.4.2.1 physicalPortsEntry OBJECT-TYPE SYNTAX PhysicalPortsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in routerPortsTable." INDEX { ifIndex } ::= { physicalPortsTable 1 } PhysicalPortsEntry ::= SEQUENCE { portMgmtTrafficEnable TruthValue, portDuplexMode INTEGER, portFunction INTEGER } -- 1.3.6.1.4.1.1916.5.3.2.4.2.1.1 portMgmtTrafficEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Determines whether controller management network traffic is allowed over this interface." ::= { physicalPortsEntry 1 } -- 1.3.6.1.4.1.1916.5.3.2.4.2.1.2 portDuplexMode OBJECT-TYPE SYNTAX INTEGER { full(1), half(2), auto(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Duplex mode for the esa ports." ::= { physicalPortsEntry 2 } -- 1.3.6.1.4.1.1916.5.3.2.4.2.1.3 portFunction OBJECT-TYPE SYNTAX INTEGER { router(1), host(2), thirdPartyAP(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the behavior of the WM physical ports." ::= { physicalPortsEntry 3 } -- 1.3.6.1.4.1.1916.5.3.2.5 adManagerObjects OBJECT IDENTIFIER ::= { summitWM 5 } -- 1.3.6.1.4.1.1916.5.3.2.5.1 adRole OBJECT-TYPE SYNTAX INTEGER { none(1), adMgr(2), adAgent(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the role of this WM in inter-WM mobility. None indicates that mobile units cannot roam to or from this WM. In any WM cluster, only one WM should be specified as adMgr, all others should be have adRole = adAgent ." ::= { adManagerObjects 1 } -- 1.3.6.1.4.1.1916.5.3.2.5.2 adIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "ifIndex of the physical port where inter-WM tunnels terminate." ::= { adManagerObjects 2 } -- 1.3.6.1.4.1.1916.5.3.2.5.3 adHeartBeatInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The time interval between inter-WM polling messages." ::= { adManagerObjects 3 } -- 1.3.6.1.4.1.1916.5.3.2.6 ntpObjects OBJECT IDENTIFIER ::= { summitWM 6 } -- 1.3.6.1.4.1.1916.5.3.2.6.1 ntpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disables support for the Network Time Protocol (NTP)." ::= { ntpObjects 1 } -- 1.3.6.1.4.1.1916.5.3.2.6.2 ntpTimezone OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the time zone where this WM resides." ::= { ntpObjects 2 } -- 1.3.6.1.4.1.1916.5.3.2.6.3 ntpTimeServer1 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Primary NTP server." ::= { ntpObjects 3 } -- 1.3.6.1.4.1.1916.5.3.2.6.4 ntpTimeServer2 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Secondary NTP server." ::= { ntpObjects 4 } -- 1.3.6.1.4.1.1916.5.3.2.6.5 ntpTimeServer3 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Tertiary NTP server." ::= { ntpObjects 5 } -- 1.3.6.1.4.1.1916.5.3.2.7 controllerStats OBJECT IDENTIFIER ::= { summitWM 7 } -- 1.3.6.1.4.1.1916.5.3.2.7.6 tunnelCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of connections to other summitWM controllers." ::= { controllerStats 6 } -- 1.3.6.1.4.1.1916.5.3.2.7.7 tunnelStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF TunnelStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "tunnelStatsTable contains a list of the IP tunnels connected to this WM for use in inter-WM mobility." ::= { controllerStats 7 } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1 tunnelStatsEntry OBJECT-TYPE SYNTAX TunnelStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for a mobility tunnel." INDEX { tunnelStartIP, tunnelEndIP } ::= { tunnelStatsTable 1 } TunnelStatsEntry ::= SEQUENCE { tunnelStartIP IpAddress, tunnelStartWM OCTET STRING, tunnelEndIP IpAddress, tunnelEndWM OCTET STRING, tunnelStatus INTEGER } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1.1 tunnelStartIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address for the start of the tunnel." ::= { tunnelStatsEntry 1 } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1.2 tunnelStartWM OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the access controller for the start of the tunnel." ::= { tunnelStatsEntry 2 } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1.3 tunnelEndIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address for the end of the tunnel." ::= { tunnelStatsEntry 3 } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1.4 tunnelEndWM OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the access controller for the end of the tunnel." ::= { tunnelStatsEntry 4 } -- 1.3.6.1.4.1.1916.5.3.2.7.7.1.5 tunnelStatus OBJECT-TYPE SYNTAX INTEGER { disconnected(1), connected(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if the mobility tunnel is up or down." ::= { tunnelStatsEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3 accessDomains OBJECT IDENTIFIER ::= { summitWMMgmt 3 } -- 1.3.6.1.4.1.1916.5.3.3.1 wmadConfigObjects OBJECT IDENTIFIER ::= { accessDomains 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.1 wmadCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of WMADs defined in wmadConfigTable." ::= { wmadConfigObjects 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.2 wmadConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains definitions of the Access Domain Segments defined on this SummitWM." ::= { wmadConfigObjects 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1 wmadConfigEntry OBJECT-TYPE SYNTAX WmadConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration elements for a specific Access Domain Segment." INDEX { wmadIfIndex } ::= { wmadConfigTable 1 } WmadConfigEntry ::= SEQUENCE { wmadDescription DisplayString, wmadAssignmentMode INTEGER, wmadMUSessionTimeout Integer32, wmadAllowMulticast TruthValue, wmadSSID DisplayString, wmadDomain DisplayString, wmadDNSServers DisplayString, wmadWINSServers DisplayString, wmadAuthModel INTEGER, wmadParentIfIndex Integer32, wmadMgmtTrafficEnable TruthValue, wmadUseDHCPRelay TruthValue, wmad3rdPartyAP TruthValue, wmadStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.1 wmadDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Textual description of the WMAD." ::= { wmadConfigEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.2 wmadAssignmentMode OBJECT-TYPE SYNTAX INTEGER { ssid(1), aaa(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Determines the method by which mobile units are assigned an address within this WMAD. If wmadAssignmentMode = ssid, any client with an SSID matching the WMAD will be assigned an address from this WMAD. If wmadAssignmentMode == aaa, then address assignment is not completed until after the user is authenticated." ::= { wmadConfigEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.3 wmadMUSessionTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Client session idle time out, in seconds." ::= { wmadConfigEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.4 wmadAllowMulticast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When true, allows IP multicast packets to be broadcast to the clients on this WMAD." ::= { wmadConfigEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.5 wmadSSID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Service Set Identifier (i.e. Network Name) that will be configured on the Altitudes associated with this WMAD." ::= { wmadConfigEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.6 wmadDomain OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Domain name to be supplied to the wireless clients if internal DHCP address assignment." ::= { wmadConfigEntry 6 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.7 wmadDNSServers OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "List of DNSs to be supplied to the wireless clients if internal DHCP address assignment." ::= { wmadConfigEntry 7 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.8 wmadWINSServers OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "List of WINSs to be supplied to the wireless clients if internal DHCP address assignment." ::= { wmadConfigEntry 8 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.9 wmadAuthModel OBJECT-TYPE SYNTAX INTEGER { none(1), captivePortal(2), dot1X(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "wmadAuthModel specifies the authentication method used for clients in the WMAD. None indicates that the WMAD is open, and no authentication is required. wmadAuthModel=captivePortal may only be specified for a WMAD with wmadAssignmentMode=ssid. Likewise, wmadAuthModel=dot1X may only be specified for a WMAD with wmadAssignmentMode=aaa." ::= { wmadConfigEntry 9 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.10 wmadParentIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the ifIndex of the parent WMAD, if this WMAD is a child. This only applies for a WMAD where wmadAssignmentMode=aaa. If this is a top level WMAD, wmadParentIfIndex will return null or 0." ::= { wmadConfigEntry 10 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.11 wmadMgmtTrafficEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether clients in the WMAD have access to WM management elements." ::= { wmadConfigEntry 11 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.12 wmadUseDHCPRelay OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When true, specifies that DHCP Relay is enabled on the WMAD." ::= { wmadConfigEntry 12 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.13 wmad3rdPartyAP OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When true, specifies that the WMAD contains 3rd party access points. Only one such WMAD may be defined for a summitWM." ::= { wmadConfigEntry 13 } -- 1.3.6.1.4.1.1916.5.3.3.1.2.1.14 wmadStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus variable for performing row operations on wmadConfigTable." ::= { wmadConfigEntry 14 } -- 1.3.6.1.4.1.1916.5.3.3.1.3 wmadDHCPRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadDHCPRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "wmadDHCPRangeTable contains the IP address ranges that DHCP will serve to clients associated with this WMAD." ::= { wmadConfigObjects 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1 wmadDHCPRangeEntry OBJECT-TYPE SYNTAX WmadDHCPRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for a DHCP range." INDEX { ifIndex, wmadDHCPRangeIndex } ::= { wmadDHCPRangeTable 1 } WmadDHCPRangeEntry ::= SEQUENCE { wmadDHCPRangeIndex Integer32, wmadDHCPRangeStart IpAddress, wmadDHCPRangeEnd IpAddress, wmadDHCPRangeType INTEGER, wmadDHCPRangeStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1.1 wmadDHCPRangeIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Index for the DHCP row element." ::= { wmadDHCPRangeEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1.2 wmadDHCPRangeStart OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "First IP address in the range." ::= { wmadDHCPRangeEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1.3 wmadDHCPRangeEnd OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Last IP address in the range." ::= { wmadDHCPRangeEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1.4 wmadDHCPRangeType OBJECT-TYPE SYNTAX INTEGER { inclusion(1), exclusion(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Determines whether addresses in the specified range will be included, or excluded by the DHCP server." ::= { wmadDHCPRangeEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.3.1.5 wmadDHCPRangeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Row status variable for row operations on the wmadDHCPRangeTable" ::= { wmadDHCPRangeEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.4 wmadCaptivePortalTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadCaptivePortalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of the Captive Portal login page for WMADs that have wmadAssignment=ssid and wmadAuthModel=captivePortal." ::= { wmadConfigObjects 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1 wmadCaptivePortalEntry OBJECT-TYPE SYNTAX WmadCaptivePortalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Captive Portal Information for the WMAD." INDEX { ifIndex } ::= { wmadCaptivePortalTable 1 } WmadCaptivePortalEntry ::= SEQUENCE { cpURL DisplayString, cpLoginLabel DisplayString, cpPasswordLabel DisplayString, cpHeaderURL DisplayString, cpFooterURL DisplayString, cpMessage DisplayString } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.1 cpURL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Redirect URL of the Captive Portal login page." ::= { wmadCaptivePortalEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.2 cpLoginLabel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Label that appears in front of the login field on the Captive Portal login page." ::= { wmadCaptivePortalEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.3 cpPasswordLabel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Label that appears in front of the password field on the Captive Portal login page." ::= { wmadCaptivePortalEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.4 cpHeaderURL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "URL of the Captive Portal header." ::= { wmadCaptivePortalEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.5 cpFooterURL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "URL of the Captive Portal footer." ::= { wmadCaptivePortalEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.4.1.6 cpMessage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "A welcome message, or set of instructions that is to appear on the Captive Portal login page." ::= { wmadCaptivePortalEntry 6 } -- 1.3.6.1.4.1.1916.5.3.3.1.5 wmadRadiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of RADIUS servers to be utilized for authentication in the WMAD." ::= { wmadConfigObjects 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1 wmadRadiusServerEntry OBJECT-TYPE SYNTAX WmadRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for a RADIUS server." INDEX { ifIndex, wmadRadiusServerIP } ::= { wmadRadiusServerTable 1 } WmadRadiusServerEntry ::= SEQUENCE { wmadRadiusServerIP IpAddress, wmadRadiusServerPort Integer32, wmadRadiusServerRetries Integer32, wmadRadiusServerTimeout Integer32, wmadRadiusServerSharedSecret DisplayString, wmadRadiusServerNASIdentifier DisplayString, wmadRadiusServerAuthType INTEGER, wmadRadiusServerRowStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.1 wmadRadiusServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the RADIUS server." ::= { wmadRadiusServerEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.2 wmadRadiusServerPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Port number for the RADIUS server." ::= { wmadRadiusServerEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.3 wmadRadiusServerRetries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries for a RADIUS authentication request." ::= { wmadRadiusServerEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.4 wmadRadiusServerTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Delay between requests." ::= { wmadRadiusServerEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.5 wmadRadiusServerSharedSecret OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Shared secret to be used between the NAS and RADIUS server." ::= { wmadRadiusServerEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.6 wmadRadiusServerNASIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "NAS identifier to be include in RADIUS request." ::= { wmadRadiusServerEntry 6 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.7 wmadRadiusServerAuthType OBJECT-TYPE SYNTAX INTEGER { pap(0), chap(1), msChap(2), msChapV2(3), notApplicable(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Challenge mechanism for the request." ::= { wmadRadiusServerEntry 7 } -- 1.3.6.1.4.1.1916.5.3.3.1.5.1.8 wmadRadiusServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus value for manipulating wmadRADIUSServerTable." ::= { wmadRadiusServerEntry 8 } -- 1.3.6.1.4.1.1916.5.3.3.1.6 wmadFilterIDTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadFilterIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of names filters for a WMAD." ::= { wmadConfigObjects 6 } -- 1.3.6.1.4.1.1916.5.3.3.1.6.1 wmadFilterIDEntry OBJECT-TYPE SYNTAX WmadFilterIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of a specific filter in the WMAD." INDEX { ifIndex, wmadFilterID } ::= { wmadFilterIDTable 1 } WmadFilterIDEntry ::= SEQUENCE { wmadFilterID DisplayString, wmadFilterIDStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.3.1.6.1.1 wmadFilterID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Filter names." ::= { wmadFilterIDEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.6.1.2 wmadFilterIDStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus for operating on wmadFilterIDTable." ::= { wmadFilterIDEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.7 wmadFilterRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadFilterRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing specific filters for a named filter." ::= { wmadConfigObjects 7 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1 wmadFilterRuleEntry OBJECT-TYPE SYNTAX WmadFilterRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Filter elements for an individual WMAD filter." INDEX { ifIndex, wmadFilterID, wmadFilterRuleOrder } ::= { wmadFilterRuleTable 1 } WmadFilterRuleEntry ::= SEQUENCE { wmadFilterRuleOrder Integer32, wmadFilterRuleDirection INTEGER, wmadFilterRuleAction INTEGER, wmadFilterRuleIPAddress IpAddress, wmadFilterRulePortLow Integer32, wmadFilterRulePortHigh Integer32, wmadFilterRuleProtocol INTEGER, wmadFilterRuleEtherType INTEGER, wmadFilterRuleStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.1 wmadFilterRuleOrder OBJECT-TYPE SYNTAX Integer32 (1..65532) MAX-ACCESS read-write STATUS current DESCRIPTION "Position of the filter in the filter list." ::= { wmadFilterRuleEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.2 wmadFilterRuleDirection OBJECT-TYPE SYNTAX INTEGER { in(1), out(2), both(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Traffic direction to apply the rule." ::= { wmadFilterRuleEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.3 wmadFilterRuleAction OBJECT-TYPE SYNTAX INTEGER { allow(1), disallow(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Allow or deny traffic for the filter." ::= { wmadFilterRuleEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.4 wmadFilterRuleIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address to apply the filter." ::= { wmadFilterRuleEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.5 wmadFilterRulePortLow OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Low port number for the filter." ::= { wmadFilterRuleEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.6 wmadFilterRulePortHigh OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "High port number for the filter." ::= { wmadFilterRuleEntry 6 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.7 wmadFilterRuleProtocol OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), tcp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specific protocol to filter." ::= { wmadFilterRuleEntry 7 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.8 wmadFilterRuleEtherType OBJECT-TYPE SYNTAX INTEGER { ip(1), arp(2), rarp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specific ethertype to filter." ::= { wmadFilterRuleEntry 8 } -- 1.3.6.1.4.1.1916.5.3.3.1.7.1.9 wmadFilterRuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus value for the wmadFilterRuleTable." ::= { wmadFilterRuleEntry 9 } -- 1.3.6.1.4.1.1916.5.3.3.1.8 wmadPrivacyTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadPrivacyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of privacy settings for the WMAD." ::= { wmadConfigObjects 8 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1 wmadPrivacyEntry OBJECT-TYPE SYNTAX WmadPrivacyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration values for a specific privacy setting." INDEX { ifIndex } ::= { wmadPrivacyTable 1 } WmadPrivacyEntry ::= SEQUENCE { wmadPrivWEPKeyType INTEGER, wmadPrivDynamicRekeyFrequency Integer32, wmadPrivWEPKeyLength Integer32, wmadPrivWPA1Enabled TruthValue, wmadPrivUseSharedKey TruthValue, wmadPrivWPASharedKey DisplayString, wmadPrivWPA2Enabled TruthValue } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.1 wmadPrivWEPKeyType OBJECT-TYPE SYNTAX INTEGER { none(1), wepstatic(2), wpapsk(3), dynamic(4), wpa(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of key in use. none(1) = not cofigured, wepstatic(2) = static WEP, wpapsk(3) = WPA Pre-Shared Key, dynamic(4) = dynamically assigned, wpa(5) = WPA." ::= { wmadPrivacyEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.2 wmadPrivDynamicRekeyFrequency OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic WEP re-keying frequency, in seconds. Setting this value to 0 disables rekeying. This value is only meaningful if wmadPrivWEPKeyType == dynamic. For any other values of wmadPrivWEPKeyType, reading or setting this value will return an unsuccessful status and will return a value of null or zero." ::= { wmadPrivacyEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.3 wmadPrivWEPKeyLength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "WEP key length, either 40 or 104 bit. If wmadPrivWEPKeyType is none, reading or setting this value will return an unsuccessful status and will return a value of null or zero." ::= { wmadPrivacyEntry 3 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.4 wmadPrivWPA1Enabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enables WPA.1 (Wi-Fi Protected Access)." ::= { wmadPrivacyEntry 4 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.5 wmadPrivUseSharedKey OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enables the use of WPA shared key for this WMAD." ::= { wmadPrivacyEntry 5 } -- 1.3.6.1.4.1.1916.5.3.3.1.8.1.6 wmadPrivWPASharedKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the WPA shared key for this WMAD. This value is logically WRITE ONLY. Attempts to read this value shall return unsuccessful status and values of null or zero." ::= { wmadPrivacyEntry 6 } -- 1.3.6.1.4.1.4329.15.3.3.1.8.1.7 wmadPrivWPA2Enabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When true, WPA v.2 support is enabled." ::= { wmadPrivacyEntry 7 } -- 1.3.6.1.4.1.1916.5.3.3.1.9 wmadWEPKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF WmadWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of WEP key entries for a static WEP definition." ::= { wmadConfigObjects 9 } -- 1.3.6.1.4.1.1916.5.3.3.1.9.1 wmadWEPKeyEntry OBJECT-TYPE SYNTAX WmadWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "WEP key for a single entry in the table." INDEX { ifIndex, wmadWEPKeyIndex } ::= { wmadWEPKeyTable 1 } WmadWEPKeyEntry ::= SEQUENCE { wmadWEPKeyIndex Integer32, wmadWEPKeyValue WEPKeytype } -- 1.3.6.1.4.1.1916.5.3.3.1.9.1.1 wmadWEPKeyIndex OBJECT-TYPE SYNTAX Integer32 (1..4) MAX-ACCESS read-write STATUS current DESCRIPTION "Table index for the WEP key." ::= { wmadWEPKeyEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.9.1.2 wmadWEPKeyValue OBJECT-TYPE SYNTAX WEPKeytype MAX-ACCESS read-write STATUS current DESCRIPTION "Value of a WEP key for this WMAD. This value is logically WRITE ONLY. Attempts to read this value shall return unsuccessful status and values of null or zero." ::= { wmadWEPKeyEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.1.10 wmad3rdPartyAPTable OBJECT-TYPE SYNTAX SEQUENCE OF Wmad3rdPartyAPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains a list of 3rd Party access points for the WM." ::= { wmadConfigObjects 10 } -- 1.3.6.1.4.1.1916.5.3.3.1.10.1 wmad3rdPartyAPEntry OBJECT-TYPE SYNTAX Wmad3rdPartyAPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for a 3rd party access point." INDEX { ifIndex, apMacAddress } ::= { wmad3rdPartyAPTable 1 } Wmad3rdPartyAPEntry ::= SEQUENCE { apMacAddress MacAddress, apIpAddress IpAddress } -- 1.3.6.1.4.1.1916.5.3.3.1.10.1.1 apMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Ethernet MAC address of the 3rd party access point." ::= { wmad3rdPartyAPEntry 1 } -- 1.3.6.1.4.1.1916.5.3.3.1.10.1.2 apIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the 3rd party access point." ::= { wmad3rdPartyAPEntry 2 } -- 1.3.6.1.4.1.1916.5.3.3.2 wmadStatsObjects OBJECT IDENTIFIER ::= { accessDomains 2 } -- 1.3.6.1.4.1.1916.5.3.3.2.1 activeWMADSessionCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of active WMADs." ::= { wmadStatsObjects 1 } -- 1.3.6.1.4.1.1916.5.3.5 altitude OBJECT IDENTIFIER ::= { summitWMMgmt 5 } -- 1.3.6.1.4.1.1916.5.3.5.1 altitudeConfigObjects OBJECT IDENTIFIER ::= { altitude 1 } -- 1.3.6.1.4.1.1916.5.3.5.1.1 altitudeCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of currently configured Altitudes associated with this summitWM." ::= { altitudeConfigObjects 1 } -- 1.3.6.1.4.1.1916.5.3.5.1.2 altitudeTable OBJECT-TYPE SYNTAX SEQUENCE OF AltitudeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains a list of all configured Altitudes associated with the summitWM." ::= { altitudeConfigObjects 2 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1 altitudeEntry OBJECT-TYPE SYNTAX AltitudeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for an access point." INDEX { altitudeIndex } ::= { altitudeTable 1 } AltitudeEntry ::= SEQUENCE { altitudeIndex Integer32, altitudeName DisplayString, altitudeDesc DisplayString, altitudeSerialNumber OCTET STRING, altitudePortifIndex InterfaceIndex, altitudeWiredIfIndex InterfaceIndex, altitudeSoftwareVersion OCTET STRING, altitudeSpecific OBJECT IDENTIFIER, altitudeBroadcastDisassociate TruthValue, altitudeRowStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.1 altitudeIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Table index for the access point." ::= { altitudeEntry 1 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.2 altitudeName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Altitude's name." ::= { altitudeEntry 2 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.3 altitudeDesc OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Text description of the Altitude." ::= { altitudeEntry 3 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.4 altitudeSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "16-character serial number of the Altitude." ::= { altitudeEntry 4 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.5 altitudePortifIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "ifIndex of the physical port to which this Altitude is assigned." ::= { altitudeEntry 5 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.6 altitudeWiredIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "ifIndex of the wired interface on the Altitude." ::= { altitudeEntry 6 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.7 altitudeSoftwareVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Software version currently installed on the Altitude." ::= { altitudeEntry 7 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.8 altitudeSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "A link back to the OID under the summitWMProducts branch that identifies the specific version of this Altitude." ::= { altitudeEntry 8 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.9 altitudeBroadcastDisassociate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "True indicates that the Altitude should broadcast disassociation requests, False indicates unicast." ::= { altitudeEntry 9 } -- 1.3.6.1.4.1.1916.5.3.5.1.2.1.10 altitudeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus for the altitudeTable." ::= { altitudeEntry 10 } -- 1.3.6.1.4.1.1916.5.3.5.1.3 altitudeRadioTable OBJECT-TYPE SYNTAX SEQUENCE OF AltitudeRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table access point radio configuration information." ::= { altitudeConfigObjects 3 } -- 1.3.6.1.4.1.1916.5.3.5.1.3.1 altitudeRadioEntry OBJECT-TYPE SYNTAX AltitudeRadioEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration information for a radio on the access point." INDEX { altitudeIndex, ifIndex } ::= { altitudeRadioTable 1 } AltitudeRadioEntry ::= SEQUENCE { altitudeRadioFrequency INTEGER } -- 1.3.6.1.4.1.1916.5.3.5.1.3.1.1 altitudeRadioFrequency OBJECT-TYPE SYNTAX INTEGER { freq50GHz(1), freq24GHz(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of radio (a or b/g)." ::= { altitudeRadioEntry 1 } -- 1.3.6.1.4.1.1916.5.3.5.1.4 radioWMADTable OBJECT-TYPE SYNTAX SEQUENCE OF RadioWMADEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of WMADs the radio is participating in." ::= { altitudeConfigObjects 4 } -- 1.3.6.1.4.1.1916.5.3.5.1.4.1 radioWMADEntry OBJECT-TYPE SYNTAX RadioWMADEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a single WMAD entry." INDEX { radioIfIndex, wmadIfIndex } ::= { radioWMADTable 1 } RadioWMADEntry ::= SEQUENCE { radioIfIndex InterfaceIndex, wmadIfIndex InterfaceIndex, radioWMADRowStatus RowStatus } -- 1.3.6.1.4.1.1916.5.3.5.1.4.1.1 radioIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Radio participating in the WMAD." ::= { radioWMADEntry 1 } -- 1.3.6.1.4.1.1916.5.3.5.1.4.1.2 wmadIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "ifIndex for the WMAD the radio is participating." ::= { radioWMADEntry 2 } -- 1.3.6.1.4.1.1916.5.3.5.1.4.1.3 radioWMADRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus for the radioWMADTable." ::= { radioWMADEntry 3 } -- 1.3.6.1.4.1.1916.5.3.5.2 altitudeStatsObjects OBJECT IDENTIFIER ::= { altitude 2 } -- 1.3.6.1.4.1.1916.5.3.5.2.1 altitudeActiveCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of active Altitude associated with this summitWM." ::= { altitudeStatsObjects 1 } -- 1.3.6.1.4.1.1916.5.3.5.2.2 altitudeStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AltitudeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of statistics for the access points." ::= { altitudeStatsObjects 2 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1 altitudeStatsEntry OBJECT-TYPE SYNTAX AltitudeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for an access point." INDEX { altitudeIndex } ::= { altitudeStatsTable 1 } AltitudeStatsEntry ::= SEQUENCE { altitudeInUcastPkts Counter64, altitudeInNUcastPkts Counter64, altitudeInOctets Counter64, altitudeInErrors Counter64, altitudeInDiscards Counter64, altitudeOutUcastPkts Counter64, altitudeOutNUcastPkts Counter64, altitudeOutOctets Counter64, altitudeOutErrors Counter64, altitudeOutDiscards Counter64, altitudeUpTime TimeTicks } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.1 altitudeInUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of unicast packets from wireless-to-wired network." ::= { altitudeStatsEntry 1 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.2 altitudeInNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-unicast packets from wireless-to-wired network." ::= { altitudeStatsEntry 2 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.3 altitudeInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets from wireless-to-wired network." ::= { altitudeStatsEntry 3 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.4 altitudeInErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of error packets from wireless-to-wired network." ::= { altitudeStatsEntry 4 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.5 altitudeInDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets from wireless-to-wired network." ::= { altitudeStatsEntry 5 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.6 altitudeOutUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of unicast packets from wired-to-wireless network." ::= { altitudeStatsEntry 6 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.7 altitudeOutNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-unicast packets from wired-to-wireless network." ::= { altitudeStatsEntry 7 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.8 altitudeOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets from wired-to-wireless network." ::= { altitudeStatsEntry 8 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.9 altitudeOutErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of error packets from wired-to-wireless network." ::= { altitudeStatsEntry 9 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.10 altitudeOutDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets from wired-to-wireless network." ::= { altitudeStatsEntry 10 } -- 1.3.6.1.4.1.1916.5.3.5.2.2.1.11 altitudeUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { altitudeStatsEntry 11 } -- 1.3.6.1.4.1.1916.5.3.6 mobileUnits OBJECT IDENTIFIER ::= { summitWMMgmt 6 } -- 1.3.6.1.4.1.1916.5.3.6.1 mobileUnitCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of clients associated with the access point." ::= { mobileUnits 1 } -- 1.3.6.1.4.1.1916.5.3.6.2 muTable OBJECT-TYPE SYNTAX SEQUENCE OF MuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of information for clients associated with the WM." ::= { mobileUnits 2 } -- 1.3.6.1.4.1.1916.5.3.6.2.1 muEntry OBJECT-TYPE SYNTAX MuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a client associated with the WM." INDEX { muMACAddress } ::= { muTable 1 } MuEntry ::= SEQUENCE { muMACAddress MacAddress, muIPAddress IpAddress, muUser OCTET STRING, muState TruthValue, muAltitudeSerialNo OCTET STRING, muWmadSSID OCTET STRING, muTxPackets Counter64, muRxPackets Counter64, muTxOctets Counter64, muRxOctets Counter64, muDuration Counter64 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.1 muMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Client MAC address." ::= { muEntry 1 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.2 muIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Client IP Address." ::= { muEntry 2 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.3 muUser OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Client login name." ::= { muEntry 3 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.4 muState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if the client is authenticated." ::= { muEntry 4 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.5 muAltitudeSerialNo OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Serial Number of the Altitude the client is associated with." ::= { muEntry 5 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.6 muWmadSSID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "SSID of the WMAD the client is associated with." ::= { muEntry 6 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.7 muTxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets trasmitted to the client." ::= { muEntry 7 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.8 muRxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received from the client." ::= { muEntry 8 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.9 muTxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets transmitted to the client." ::= { muEntry 9 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.10 muRxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received from the client." ::= { muEntry 10 } -- 1.3.6.1.4.1.1916.5.3.6.2.1.11 muDuration OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Time client has been associated with the WM." ::= { muEntry 11 } -- 1.3.6.1.4.1.1916.5.3.7 associations OBJECT IDENTIFIER ::= { summitWMMgmt 7 } -- 1.3.6.1.4.1.1916.5.3.7.1 assocCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Total number of current client associations to the access point." ::= { associations 1 } -- 1.3.6.1.4.1.1916.5.3.7.2 assocTable OBJECT-TYPE SYNTAX SEQUENCE OF AssocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of information about clients associated with the access point." ::= { associations 2 } -- 1.3.6.1.4.1.1916.5.3.7.2.1 assocEntry OBJECT-TYPE SYNTAX AssocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a single client in the association table." INDEX { assocMUMacAddress, altitudeIndex, assocStartSysUpTime } ::= { assocTable 1 } AssocEntry ::= SEQUENCE { assocMUMacAddress MacAddress, assocStartSysUpTime TimeTicks, assocTxPackets Counter64, assocRxPackets Counter64, assocTxOctets Counter64, assocRxOctets Counter64, assocDuration Integer32, assocWmadIfIndex InterfaceIndex } -- 1.3.6.1.4.1.1916.5.3.7.2.1.1 assocMUMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the client." ::= { assocEntry 1 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.2 assocStartSysUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "How long the client has been associated to the access point." ::= { assocEntry 2 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.3 assocTxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Nubmer of tx packets to the client." ::= { assocEntry 3 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.4 assocRxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets from the client." ::= { assocEntry 4 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.5 assocTxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets sent to the client." ::= { assocEntry 5 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.6 assocRxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received from the client." ::= { assocEntry 6 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.7 assocDuration OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Length of time since last association." ::= { assocEntry 7 } -- 1.3.6.1.4.1.1916.5.3.7.2.1.8 assocWmadIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Index of WMAD to which the MU is associated with." ::= { assocEntry 8 } -- 1.3.6.1.4.1.1916.5.3.8 protocols OBJECT IDENTIFIER ::= { summitWMMgmt 8 } -- 1.3.6.1.4.1.1916.5.3.8.1 wmadc OBJECT IDENTIFIER ::= { protocols 1 } -- 1.3.6.1.4.1.1916.5.3.9 logNotifications OBJECT IDENTIFIER ::= { summitWMMgmt 9 } -- 1.3.6.1.4.1.1916.5.3.9.1 logEventSeverityThreshold OBJECT-TYPE SYNTAX LogEventSeverity MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the minimum level at which the SNMP agent will send notifications for log events. I.e., setting this value to 'major' will send notifcations for critical and major log events. Setting the threshold to minor will trap critical, major, and minor events. " ::= { logNotifications 1 } -- 1.3.6.1.4.1.1916.5.3.9.3 logEventSeverity OBJECT-TYPE SYNTAX LogEventSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the severity of the most recently trapped summitWMLogAlarm notification." ::= { logNotifications 3 } -- 1.3.6.1.4.1.1916.5.3.9.4 logEventComponent OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Contains the component which sent the most recently trapped summitWMLogAlarm notification." ::= { logNotifications 4 } -- 1.3.6.1.4.1.1916.5.3.9.5 logEventDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the description of the most recently trapped summitWMLogAlarm." ::= { logNotifications 5 } -- 1.3.6.1.4.1.1916.5.3.9.6 summitWMLogAlarm NOTIFICATION-TYPE OBJECTS { logEventSeverity, logEventComponent, logEventDescription } STATUS current DESCRIPTION "Components of an alarm." ::= { logNotifications 6 } -- 1.3.6.1.4.1.1916.5.3.19 altitudeNotifications OBJECT IDENTIFIER ::= { summitWMMgmt 19 } -- 1.3.6.1.4.1.1916.5.3.19.1 altitudeEventId OBJECT-TYPE SYNTAX INTEGER { altitudePollTimeout(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies event associated with Altitude or Altitude tunnel: altitudePollTimeout - an event triggered when Altitude disconnects from WM" ::= { altitudeNotifications 1 } -- 1.3.6.1.4.1.1916.5.3.19.2 altitudeEventDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the description of the most recently triggered event." ::= { altitudeNotifications 2 } -- 1.3.6.1.4.1.1916.5.3.19.3 altitudeEventSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "16-character serial number of the Altitude." ::= { altitudeNotifications 3 } -- 1.3.6.1.4.1.1916.5.3.19.4 altitudeTunnelAlarm NOTIFICATION-TYPE OBJECTS { altitudeEventId, altitudeEventDescription, altitudeEventSerialNumber } STATUS current DESCRIPTION "alarm associated with Altitude and Altitude interface." ::= { altitudeNotifications 4 } -- 1.3.6.1.4.1.1916.5.3.30 summitWMConformance OBJECT IDENTIFIER ::= { summitWMMgmt 30 } -- this module -- 1.3.6.1.4.1.1916.5.3.30.1 summitWMModule MODULE-COMPLIANCE STATUS current DESCRIPTION "Conformance definition for the WM MIB." MODULE -- this module MANDATORY-GROUPS { summitWMGroup } ::= { summitWMConformance 1 } -- 1.3.6.1.4.1.1916.5.3.30.2 summitWMGroup OBJECT-GROUP OBJECTS { sysSoftwareVersion, sysLogLevel, logEventSeverityThreshold, logEventSeverity, logEventComponent, logEventDescription, altitudeEventId, altitudeEventDescription, altitudeEventSerialNumber, assocTxPackets, assocRxPackets, assocTxOctets, assocRxOctets, assocDuration, assocCount, assocMUMacAddress, assocStartSysUpTime, muTxPackets, muRxPackets, muTxOctets, muRxOctets, muDuration, mobileUnitCount, muMACAddress, wmadIfIndex, radioWMADRowStatus, altitudeSpecific, altitudeRowStatus, radioIfIndex, altitudeDesc, altitudeSerialNumber, altitudePortifIndex, wmadFilterRulePortLow, wmadFilterRulePortHigh, altitudeInUcastPkts, altitudeInNUcastPkts, altitudeInOctets, altitudeInErrors, altitudeInDiscards, altitudeOutUcastPkts, altitudeOutNUcastPkts, altitudeOutOctets, altitudeOutErrors, altitudeOutDiscards, cpPasswordLabel, cpLoginLabel, cpURL, wmadDHCPRangeIndex, wmad3rdPartyAP, wmadUseDHCPRelay, wmadMgmtTrafficEnable, wmadAuthModel, physicalPortCount, altitudeSoftwareVersion, mgmtPortIfIndex, mgmtPortHostname, mgmtPortPrimaryDNS, mgmtPortSecondaryDNS, mgmtPortDomain, portMgmtTrafficEnable, portDuplexMode, portFunction, adRole, adIfIndex, adHeartBeatInterval, ntpEnabled, ntpTimezone, ntpTimeServer1, ntpTimeServer2, ntpTimeServer3, tunnelCount, wmadCount, wmadDescription, wmadAssignmentMode, wmadMUSessionTimeout, wmadAllowMulticast, wmadSSID, wmadDomain, wmadDNSServers, wmadWINSServers, wmadParentIfIndex, wmadStatus, wmadDHCPRangeStart, wmadDHCPRangeEnd, wmadDHCPRangeType, wmadDHCPRangeStatus, wmadRadiusServerIP, wmadRadiusServerPort, wmadRadiusServerRetries, wmadRadiusServerTimeout, wmadRadiusServerSharedSecret, wmadRadiusServerNASIdentifier, wmadRadiusServerAuthType, wmadRadiusServerRowStatus, wmadFilterID, wmadFilterIDStatus, wmadFilterRuleOrder, wmadFilterRuleDirection, wmadFilterRuleAction, wmadFilterRuleIPAddress, wmadFilterRuleProtocol, wmadFilterRuleEtherType, wmadFilterRuleStatus, wmadPrivWEPKeyType, wmadPrivDynamicRekeyFrequency, wmadPrivWEPKeyLength, wmadPrivWPA1Enabled, wmadPrivUseSharedKey, wmadPrivWPASharedKey, wmadWEPKeyIndex, wmadWEPKeyValue, activeWMADSessionCount, altitudeCount, altitudeIndex, cpHeaderURL, cpFooterURL, cpMessage, apMacAddress, apIpAddress, summitWMAppLogFacility, serviceLogFacility, sysLogServerIP, sysLogServerPort, sysLogServerRowStatus, sysLogServerIndex, altitudeActiveCount, altitudeWiredIfIndex, sysLogServerEnabled, altitudeUpTime, assocWmadIfIndex, muIPAddress, muUser, muState, muAltitudeSerialNo, muWmadSSID, altitudeBroadcastDisassociate, altitudeName, sysSerialNo, wmadPrivWPA2Enabled, altitudeRadioFrequency, includeAllServiceMessages, tunnelStartIP, tunnelStartWM, tunnelEndIP, tunnelEndWM, tunnelStatus } STATUS current DESCRIPTION "Conformance groups." ::= { summitWMConformance 2 } -- 1.3.6.1.4.1.1916.5.3.30.3 summitWMAlarms NOTIFICATION-GROUP NOTIFICATIONS { summitWMLogAlarm, altitudeTunnelAlarm } STATUS current DESCRIPTION "Conformance information for the alarm groups." ::= { summitWMConformance 3 } END -- -- EXTREME-SUMMIT-WM-MIB.my --