CXISDN-MIB DEFINITIONS ::= BEGIN IMPORTS Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 DisplayString FROM RFC1213-MIB cxISDN,SapIndex,Alias FROM CXProduct-SMI; isdnSoftwareVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Identifies the main version and revision numbers (separated by a period) of the ISDN software layer. Default Value: none" ::= { cxISDN 1 } isdnTraps OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether this software layer produces the isdnCCSapStatusIndication and isdnL3SapStatusIndication traps. Options: disabled(1): software layer does not produce CC and L3 status indication traps enabled (1): software layer produces CC and L3 status indication traps Default Value: disabled Configuration Changed: administrative " DEFVAL { disabled } ::= { cxISDN 2 } -- Lower Service Access Point Configuration Table -- The table describing: -- parameters required to configure a lower service access point -- controls available to manipulate a lower service access point -- status available for monitoring the current state of the lower service -- access point statistics available for monitoring any lower service access -- point -- The Lower Service Access Points here is considered as a the lower access -- point of Digital Subscriber Line (DSL) of this module. In fact, this -- lower access point support two SAPs (0 and 16). This Lower Service -- Access Points is used to communicate with one LAPD channel. So, every -- ISDN Basic Rate Interface line (BRI) will be handled by one of these -- Lower Service Access Point. -- The default values for all the timers object are the one defined in the -- Q.931 CCITT recommendation. isdnL3SapTable OBJECT-TYPE SYNTAX SEQUENCE OF IsdnL3SapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing configuration, controls, status and statistics information about each ISDN layer lower service access point." ::= { cxISDN 20 } isdnL3SapEntry OBJECT-TYPE SYNTAX IsdnL3SapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The parameters for a specific lower service access point." INDEX { isdnL3SapNumber } ::= { isdnL3SapTable 1 } IsdnL3SapEntry ::= SEQUENCE { -- Parameters isdnL3SapNumber SapIndex, isdnL3SapRowStatus INTEGER, isdnL3SapAlias Alias, isdnL3SapCompanionAlias Alias, isdnL3SapUserNetType INTEGER, isdnL3SapT303Timer INTEGER, isdnL3SapT304Timer INTEGER, isdnL3SapT305Timer INTEGER, isdnL3SapT308Timer INTEGER, isdnL3SapT310Timer INTEGER, isdnL3SapT313Timer INTEGER, isdnL3SapT318Timer INTEGER, isdnL3SapT319Timer INTEGER, isdnL3SapDefTimerCfg INTEGER, -- Control -- Status isdnL3SapStatusEvent INTEGER, isdnL3SapDslType INTEGER, isdnL3SapBRIType INTEGER -- Statistics } isdnL3SapNumber OBJECT-TYPE SYNTAX SapIndex ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the row containing objects for configuring (or monitoring) a SAP that is associated with another SAP in the LAPD software layers. Note: The SAP number has to be the same than the Digital Subscriber Line number used in the BCM software layer. Range of Values: 1-6 Default Value: none" ::= { isdnL3SapEntry 1 } isdnL3SapRowStatus OBJECT-TYPE SYNTAX INTEGER { invalid (1), valid (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether this SAP is to be removed from service (i.e. invalidated) within the ISDN software layer. Options: invalid (1): row is flagged; after next reset values will be disabled and row will be deleted from table valid (2): values are enabled Default Value: none Configuration Changed: administrative " ::= { isdnL3SapEntry 2 } isdnL3SapAlias OBJECT-TYPE SYNTAX Alias ACCESS read-write STATUS mandatory DESCRIPTION "Determines the textual name identifying this lower SAP. Range of Values: 0-16 alphanumeric characters beginning with a non-numeric character Default Value: none Configuration Changed: administrative " ::= { isdnL3SapEntry 3 } isdnL3SapCompanionAlias OBJECT-TYPE SYNTAX Alias ACCESS read-write STATUS mandatory DESCRIPTION "Determines the textual name identifying this SAPs companion SAP in the LAPD software layer. Range of Values: 0-16 alphanumeric characters beginning with a non-numeric character Default Value: none Configuration Changed: administrative " ::= { isdnL3SapEntry 4 } isdnL3SapUserNetType OBJECT-TYPE SYNTAX INTEGER { user (1), network (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the Basic Rate Interface emulation for this SAP. Options: user (1): BRI type is User network (2): BRI type is Network (for future use) Default Value: user Configuration Changed: administrative " DEFVAL { user } ::= { isdnL3SapEntry 10 } isdnL3SapT303Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for an Alerting, Connect, Setup Acknowledge, Call Proceeding, or Release Complete message after sending a Setup message. Range of Values: 0-255 Default Value: 4 Configuration Changed: administrative " DEFVAL { 4 } ::= { isdnL3SapEntry 11 } isdnL3SapT304Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Call Proceeding, Alerting, Connect, or Disconnect message after sending an Information message. Range of Values: 0-255 Default Value: 15 Configuration Changed: administrative " DEFVAL { 15 } ::= { isdnL3SapEntry 12 } isdnL3SapT305Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Release or Disconnect message after sending a Disconnect message. Range of Values: 0-255 Default Value: 30 Configuration Changed: administrative " DEFVAL { 30 } ::= { isdnL3SapEntry 13 } isdnL3SapT308Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Release or Release Complete message after sending a Release message. Range of Values: 0-255 Default Value: 4 Configuration Changed: administrative " DEFVAL { 4 } ::= { isdnL3SapEntry 14 } isdnL3SapT310Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for an Alerting, Connect, Disconnect or Progress message after receiving a Call Proceeding message. Range of Values: 0-255 Default Value: 10 Configuration Changed: administrative " DEFVAL { 10 } ::= { isdnL3SapEntry 15 } isdnL3SapT313Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Connect Acknowledge message after sending a Connect message. Range of Values: 0-255 Default Value: 4 Configuration Changed: administrative " DEFVAL { 4 } ::= { isdnL3SapEntry 16 } isdnL3SapT318Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Resume Acknowledge or Resume Reject message after sending a Resume message. Range of Values: 0-255 Default Value: 4 Configuration Changed: administrative " DEFVAL { 4 } ::= { isdnL3SapEntry 17} isdnL3SapT319Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for a Suspend Acknowledge or Suspend Reject message after sending a Suspend message. Range of Values: 0-255 Default Value: 4 Configuration Changed: administrative " DEFVAL { 4 } ::= { isdnL3SapEntry 18 } isdnL3SapDefTimerCfg OBJECT-TYPE SYNTAX INTEGER { noDefCfg (1), defCfg (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether isdnL3SapT303Timer, isdnL3SapT304Timer, isdnL3SapT305Timer, isdnL3SapT308Timer, isdnL3SapT310Timer, isdnL3SapT313Timer, isdnL3SapT318Timer and isdnL3SapT319Timer will revert immediately to their default values if the value of this object has previously permitted these values to be changed from their defaults. Options: noDefCfg (1): timer values can be or have been modified DefCfg (2): timer value will maintain or return to their defaults Default Value: DefCfg Configuration Changed: administrative " DEFVAL { defCfg } ::= { isdnL3SapEntry 19 } isdnL3SapStatusEvent OBJECT-TYPE SYNTAX INTEGER { noEvent (1), badCfgVersion (2), badDslID (3), dslInUse (4), dslNotInUse (5), noNLCB (6), nlcbInitErr (7), badSwitchType (8), nlcbPoolErr (9) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates a status generated by the isdnL3SapStatusIndication trap. Note: This value will always read noEvent unless isdnTraps has been enabled and an event has been trapped. Options: noEvent (1): no trapped event badCfgVersion (2): configuration template not current badDslID (3): wrong Digital Subscriber Line dslInUse (4): Digital Subscriber Line in use dslNotInUse (5): Digital Subscriber Line not available noNLCB (6): network layer control block not available nlcbInitErr (7): network layer control block initialization error badSwitchType (8): incorrect switch-type configuration nlcbPoolErr (9) no more network layer control blocks Default Value: noEvent" ::= { isdnL3SapEntry 40 } isdnL3SapDslType OBJECT-TYPE SYNTAX INTEGER { none (1), bri (2), pri (3) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the type of physical interface for this SAP. Options: none (1): SAP has no interface bri (2) SAP uses a Basic Rate Interface pri (3) SAP uses a Primary Rate Interface Default Value: none" ::= { isdnL3SapEntry 41 } isdnL3SapBRIType OBJECT-TYPE SYNTAX INTEGER { none (1), u (2), s-t (3) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the BRI type for this SAP. Options: none (1): SAP has no BRI interface u (2): BRI type is U s-t (3): BRI type is S/T Default Value: none" DEFVAL { none } ::= { isdnL3SapEntry 42 } -- Upper Service Access Point Configuration Table -- The table describing: -- parameters required to modify parameters at a upper service access point -- controls available to manipulate a upper service access point -- status available for monitoring the current state of the upper service -- access point -- statistics available for monitoring any upper service access point isdnCCSapTable OBJECT-TYPE SYNTAX SEQUENCE OF IsdnCCSapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing configuration information about each upper service access point." ::= { cxISDN 21 } isdnCCSapEntry OBJECT-TYPE SYNTAX IsdnCCSapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The parameters for a specific upper service access point." INDEX { isdnCCSapNumber } ::= { isdnCCSapTable 1 } IsdnCCSapEntry ::= SEQUENCE { -- Parameters isdnCCSapNumber SapIndex, isdnCCSapRowStatus INTEGER, isdnCCSapAlias Alias, isdnCCSapSwitchType INTEGER, isdnCCSapInitTerminal INTEGER, isdnCCSapDNRouting INTEGER, isdnCCSapBearerRouting INTEGER, isdnCCSapBearerType INTEGER, isdnCCSapDirectoryNumber DisplayString, isdnCCSapSPID DisplayString, isdnCCSapSubAddress DisplayString, isdnCCSapT415Timer INTEGER, -- Control -- Status isdnCCSapStatusEvent INTEGER, isdnCCSapInUse INTEGER, isdnCCSapActiveCalls Counter -- Statistics } isdnCCSapNumber OBJECT-TYPE SYNTAX SapIndex ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the row containing objects for configuring (or monitoring) a SAP that is associated with the corresponding SAP in the BCM software layer. Note: The SAP number has to be the same than the Digital Subscriber Line number used in the BCM software layer. Range of Values: 1-6 Default Value: none" ::= { isdnCCSapEntry 1 } isdnCCSapRowStatus OBJECT-TYPE SYNTAX INTEGER { invalid (1), valid (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether this SAP is to be removed from service (i.e. invalidated) within the ISDN software layer. Options: invalid (1): row is flagged; after next reset values will be disabled and row will be deleted from table valid (2): values are enabled Default Value: none Configuration Changed: administrative " ::= { isdnCCSapEntry 2 } isdnCCSapAlias OBJECT-TYPE SYNTAX Alias ACCESS read-write STATUS mandatory DESCRIPTION "Determines the textual name identifying this upper SAP. Range of Values:0-16 alphanumeric characters beginning with a non-numeric character Default Value: none Configuration Changed: administrative " ::= { isdnCCSapEntry 3 } isdnCCSapSwitchType OBJECT-TYPE SYNTAX INTEGER { unspecified (1), bri-1TR6 (2), -- Germany / 1TR6 bri-5ESS (3), -- U.S.A / At&T 5ESS bri-CCITT (4), -- CCITT Q.931 bri-DMS100 (5), -- U.S.A / Norther Telecom bri-KDD (6), -- Japan / KDD bri-NET3 (7), -- Europe / Net3 bri-NI1 (8), -- U.S.A / National ISDN 1 bri-NI2 (9), -- U.S.A / National ISDN 2 bri-NTT (10), -- Japan / NTT bri-TS013 (11), -- Australia / TS013 bri-VN (12) -- France / VN } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the type of protocol supported by the switch providing the CX 900 with ISDN access. Options: unspecified (1): unspecified bri-1TR6 (2): Germany / 1TR6 bri-5ESS (3): U.S.A / At&T 5ESS bri-CCITT (4): CCITT Q.931 bri-DMS100 (5): U.S.A / Norther Telecom bri-KDD (6): Japan / KDD bri-NET3 (7): Europe / Net3 bri-NI1 (8): U.S.A / National ISDN 1 bri-NI2 (9): U.S.A / National ISDN 2 bri-NTT (10): Japan / NTT bri-TS013 (11): Australia / TS013 bri-VN (12): France / VN Default Value: bri-NI1 Configuration Changed: administrative " DEFVAL { bri-NI1 } ::= { isdnCCSapEntry 10 } isdnCCSapInitTerminal OBJECT-TYPE SYNTAX INTEGER { nit (1), -- Non-Initializing Terminal fit (2) -- Fully Initializing Terminal } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the initializing characteristics of the ISDN software layer of the CX 900. Options: nit (1): non-initializing terminal fit (2) fully-initializing terminal (North American Note: FIT requires terminal registration. Default Value: nit Configuration Changed: administrative " DEFVAL { nit } ::= { isdnCCSapEntry 11} isdnCCSapDNRouting OBJECT-TYPE SYNTAX INTEGER { no (1), yes (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether incoming calls will be checked against End-Point ID (EPID). Options: no (1): incoming call not checked against EPID yes (2): incoming call checked against EPID Note: Incoming call not containing EPID will be checked against Directory Number (DN). Default Value: no Configuration Changed: administrative " DEFVAL { no } ::= { isdnCCSapEntry 12 } isdnCCSapBearerRouting OBJECT-TYPE SYNTAX INTEGER { no (1), yes (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether incoming calls will be checked against the bearer-type specified in isdnCCSapBearerType Options: no (1): incoming call not checked against bearer-type yes (2): incoming call checked against bearer-type Default Value: no Configuration Changed: administrative " DEFVAL { no } ::= { isdnCCSapEntry 13 } isdnCCSapBearerType OBJECT-TYPE SYNTAX INTEGER { voice-call (1), circuit-sw-data-call (2), packet-sw-data-call (3) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the bearer-type that will be checked if isdnCCSapBearerType is set to yes. Options: voice call (1): call is voice circuit-sw-data-call (2): call is circuit- switched data packet-sw-data-call (3): call is packet- switched data Default Value: circuit-sw-data-call Configuration Changed: administrative " DEFVAL { circuit-sw-data-call } ::= { isdnCCSapEntry 14 } isdnCCSapDirectoryNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Determines the address or calling number assigned to the subcriber interface of the CX900. Range of Values: 0-16 numeric characters (namely, 0123456789*#) Default Value: none Configuration Changed: administrative " DEFVAL { "" } ::= { isdnCCSapEntry 15 } isdnCCSapSPID OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Determines the Service Profile Identifier (SPID) for the subscriber interface of the CX900. This object is meaningful only in North America. SPIDs are required for DMS-100 and NI-1 switches but optional for 5ESS switches. Range of Values: 0-20 Default Value: none Configuration Changed: administrative " DEFVAL { "" } ::= { isdnCCSapEntry 16 } isdnCCSapSubAddress OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Determines the subaddress (DSS1) that can be used with object isdnCCSapDirectoryNumber to specify an end-point user to be reached. Range of Values: 0-20 Default Value: none Configuration Changed: administrative " DEFVAL { "" } ::= { isdnCCSapEntry 17 } isdnCCSapT415Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the interval in seconds that the ISDN software layer will wait for completion of terminal initialization. If the Information and SPID messages fail during this interval, they will be permitted only one retransmission. Range of Values: 0-255 Default Value: 20 Configuration Changed: administrative " DEFVAL { 20 } ::= { isdnCCSapEntry 18 } isdnCCSapStatusEvent OBJECT-TYPE SYNTAX INTEGER { noEvent (1), badCfgVersion (2), badDslID (3), badCes (4), badSwitchType (5), cbPollErr (6), dslInUseErr (7), dslNotCfgErr (8), dslNotInUse (9), noHostCB (10), noT415 (11) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates a status generated by the isdnCCSapStatusIndication trap. Note: This value will always read noEvent unless isdnTraps has been enabled and an event has been trapped. Options: noEvent (1): no trapped event badCfgVersion (2): configuration template not current badDslID (3): wrong Digital Subscriber Line badCes (4): bad connection end-point badSwitchType (5): incorrect switch-type configuration cbPollErr (6): call control block error dslInUseErr (7): Digital Subscriber Line in use dslNotCfgErr (8): Digital Subscriber Line not configured dslNotInUse (9): Digital Subscriber Line not available noHostCB (10): no host control block noT415 (11): no T415 timer Default Value: noEvent" ::= { isdnCCSapEntry 40 } isdnCCSapInUse OBJECT-TYPE SYNTAX INTEGER { no (1), yes (2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether this upper SAP has been properly initialized and is now in use. Options: no (1): SAP has not been initialized yes (2): SAP is in use Default Value: none" ::= { isdnCCSapEntry 41 } isdnCCSapActiveCalls OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current number of active calls at this SAP. Range of Values: 0-2 Default Value: none" ::= { isdnCCSapEntry 42 } -- Debug Table -- This table is used to get log files of different structure of the code to -- be debugged. -- The table are the following: -- L3: NLCBs (Network Link Control Block structure) -- CC: CCDsl (Call Control Dsl context structure) -- CC: HCB (Host Control Block structure) -- CC: CCB (Call Control Block structures) -- "L3" being the "layer 3", and "CC" being the "Call Control" layer. isdnDebugTable OBJECT-TYPE SYNTAX SEQUENCE OF IsdnDebugEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing control to access debugging information." ::= { cxISDN 22 } isdnDebugEntry OBJECT-TYPE SYNTAX IsdnDebugEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The parameters for a specific structure debugging information." INDEX { isdnDebugNumber } ::= { isdnDebugTable 1 } IsdnDebugEntry ::= SEQUENCE { isdnDebugNumber SapIndex, isdnDebugCCB INTEGER, isdnDebugHCB INTEGER, isdnDebugCCDsl INTEGER, isdnDebugNLCB INTEGER } isdnDebugNumber OBJECT-TYPE SYNTAX SapIndex ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the row containing objects for creating diagnostic files for this upper SAP. Range of Values: 1-6 Default Value: none" ::= { isdnDebugEntry 1 } isdnDebugCCB OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Creates a file that includes the following Call Control Block information: - DSL = #XX - CCB = #XX - State = 0xXXXX - CallType = 0xXXXX - B-Chan = 0xXXXX - Call-ID = 0xXXXX - CallRef = 0xXXXX - Ces = 0xXX - Sapi = 0xXX - MakePrivateMsg = 0xXX - H cbIndex = 0xXXXX - CallRefLen = 0xXXXX - Cause = 0xXXXX - Host-Specifier = 0xXXXX - Host-ID = 0xXXXX - SendClearConf = 0xXX - Diagnostics = 0xXX - CollectAddress = 0xXX - Service = 0xXXXX" ::= { isdnDebugEntry 10 } isdnDebugHCB OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Creates a file that includes the following Host Control Block information: - DSL = #XX - HCB = #XX - Directory = XXXXXXXXXXXXXXXXXXXX - SPID = XXXXXXXXXXXXXXXXXXXX epid(0) - epsf = 0xXX - usid = 0xXXXX - tid = 0xXXXX epid[1] - epsf = 0xXX - usid = 0xXXXX - tid = 0xXXXX - Busy[0] = 0xXX, - Busy[1] = 0xXX - Terminal-state = 0xXX - Timer-T415 = 0xXXXX - Bearer-Routing = 0xXX - Host-ID = 0xXXXX - Ces = 0xXX - Initializing-Terminal = 0xXX" ::= { isdnDebugEntry 11 } isdnDebugCCDsl OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Creates a file that includes the following Call Control DSL information: - DSL = #XX - InUse = 0xXXXX - ActiveCCBs = 0xXXXX - Cause-Location = XXXXXX - Cd-Numb-Plan = XXXXXX - Cd-Numb-Type = XXXXXX - Cd-Sub-Type = XXXXXX - Cr-Numb-Plan = XXXXXX - Cr-Numb-Type = XXXXXX - Cr-Prest-Ind = XXXXXX - Cr-Scrn-Ind = XXXXXX - Cr-Sub-Type = XXXXXX - Facility-Code = XXXXXX - HL-Coding-Std = XXXXXX - HL-Interpret = XXXXXX - HL-Presentat = XXXXXX - HL-Teleservice = XXXXXX - L2-Prot = XXXXXX - L3-Prot = XXXXXX - Sig-Val = XXXXXX - Status = XXXXXX - Transmit-Attr = XXXXXX - Xfer-Cap = XXXXXX - Xfer-Mode = XXXXXX - Xfer-Prot = XXXXXX - Xfer-Rate = XXXXXX - Prog-Coding = XXXXXX - Prog-Loc = XXXXX - Prog-desc = XXXXXX - Ind-Val = XXXXXX" ::= { isdnDebugEntry 12 } isdnDebugNLCB OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Creates a file that includes the following Network Link Control Block information: - DSL = #XX - NLCB = #XX - DslID = 0xXXXX - Ces = 0xXX - CallID = 0xXXXX - ChanID = 0xXXXX - CallReflen = 0xXX - CallRef = 0xXXXX - State = 0xXXXX - Event = 0xXXXX - Timer-T304 = 0xXXXX - Timer-T310 = 0xXXXX - T303-First = 0xXX - T308-First = 0xXX - T313-First = 0xXX - UserOriginated = 0xXX - Internal = 0xXX - Cause = 0xXX - PreviousCause = 0xXX" ::= { isdnDebugEntry 13 } -- Traps isdnL3SapStatusIndication TRAP-TYPE ENTERPRISE cxISDN VARIABLES { isdnL3SapNumber, isdnL3SapStatusEvent } DESCRIPTION "Indicates that an event specified in isdnL3SapStatusEvent has occurred." ::= 1 isdnCCSapStatusIndication TRAP-TYPE ENTERPRISE cxISDN VARIABLES { isdnCCSapNumber, isdnCCSapStatusEvent } DESCRIPTION "Indicates that an event specified in isdnCCSapStatusEvent has occurred." ::= 2 END