-- This file is corresponding to Release 6.1.2.100 from 2001/09/26 00:00:00 -- (C)opyright 1991-1999 BinTec Communications AG, All Rights Reserved -- $RCSfile: mibx21,v $ -- $Revision: 1.10 $ BIANCA-BRICK-X21-MIB DEFINITIONS ::= BEGIN IMPORTS Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; org OBJECT IDENTIFIER ::= { iso 3 } dod OBJECT IDENTIFIER ::= { org 6 } internet OBJECT IDENTIFIER ::= { dod 1 } private OBJECT IDENTIFIER ::= { internet 4 } enterprises OBJECT IDENTIFIER ::= { private 1 } bintec OBJECT IDENTIFIER ::= { enterprises 272 } bibo OBJECT IDENTIFIER ::= { bintec 4 } x21 OBJECT IDENTIFIER ::= { bibo 10 } -- Interfaces Group -- Management Information for the X21 Subsystem of the BIANCA/BRICK Date ::= INTEGER HexValue ::= INTEGER x21IfTable OBJECT-TYPE SYNTAX SEQUENCE OF X21IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The x21IfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected X21 interface. Entries can only be added or deleted by the system. Creating entries: Entries are created by the system only when a new X21 module is installed. Deleting entries: Entries are removed by the system after the appropriate X21 module is removed." ::= { x21 1 } x21IfEntry OBJECT-TYPE SYNTAX X21IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { x21IfIndex } ::= { x21IfTable 1 } X21IfEntry ::= SEQUENCE { x21IfIndex INTEGER, x21IfL1State INTEGER, x21IfL1Mode INTEGER, x21IfIfLeads INTEGER, x21IfSpeed INTEGER, x21IfL2Mode INTEGER, -- Statistics x21IfSpeedReal Counter, x21IfRxPackets Counter, x21IfRxOctets Counter, x21IfTxPackets Counter, x21IfTxOctets Counter, x21IfRxResets Counter, x21IfRxAborts Counter, x21IfRxOverruns Counter, x21IfRxCRCErrors Counter, x21IfRxGiantFrames Counter, x21IfTxResets Counter, x21IfTxAborts Counter, x21IfTxUnderruns Counter, x21IfTxGiantFrames Counter } x21IfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Unique index of the X21 interface." ::= { x21IfEntry 1 } x21IfL1State OBJECT-TYPE SYNTAX INTEGER { dn(1), -- inactive up(2) -- active } ACCESS read-only STATUS mandatory DESCRIPTION "The X21 physical layer state dn(1) physical layer is inactive; up(2) physical layer is active;" ::= { x21IfEntry 2 } x21IfL1Mode OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The physical layer (layer 1) mode. When configured as DCE(2) the X21 interface provides the clock." ::= { x21IfEntry 3 } x21IfIfLeads OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The value of IfLeads has influence on the state of the physical layer (L1State). When configured as IfLeads=enabled(1), the state of the physical layer depends on the signals of the X.21 interface pins `Indication' and `Control'. When configured as IfLeads=disabled(2), the state of the physical layer stays always up." ::= { x21IfEntry 4 } x21IfSpeed OBJECT-TYPE SYNTAX INTEGER { s2048k(1), s1024k(2), s512k(3), s256k(4), s128k(5), s64000(6), s38400(7), s19200(8), s14400(9), s9600(10), s2400(11) } ACCESS read-write STATUS mandatory DESCRIPTION "The X21 interface speed in bits per second. The range can be configured between 2Mbits and 2400 Bits per second." ::= { x21IfEntry 5 } x21IfL2Mode OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), auto(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE(1) the address in a command frame is 0x01, when configured as DCE(2) it is 0x03. For response frames it is vice versa. When configured as AUTO(3), layer 2 is set to the same mode like L1Mode is set." ::= { x21IfEntry 6 } x21IfSpeedReal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The measured X21 interface speed in bits per second." ::= { x21IfEntry 7 } x21IfRxPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received valid Frames." ::= { x21IfEntry 8 } x21IfRxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received bytes." ::= { x21IfEntry 9 } x21IfTxPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted valid Frames." ::= { x21IfEntry 10 } x21IfTxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted bytes." ::= { x21IfEntry 11 } x21IfRxResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly." ::= { x21IfEntry 12 } x21IfRxAborts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence." ::= { x21IfEntry 13 } x21IfRxOverruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver overruns. If the X21 card is unable to grant sufficiently soon/often the bus, the 32-character RxFIFO may fill up. This leads to loss of data." ::= { x21IfEntry 14 } x21IfRxCRCErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of corrupted frames. Errors due to interference on the X21 cable." ::= { x21IfEntry 15 } x21IfRxGiantFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed." ::= { x21IfEntry 16 } x21IfTxResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly." ::= { x21IfEntry 17 } x21IfTxAborts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as illegal." ::= { x21IfEntry 18 } x21IfTxUnderruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter underruns. The serial data for the X21 card is supplied too slowly." ::= { x21IfEntry 19 } x21IfTxGiantFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size." ::= { x21IfEntry 20 } END -- of BIANCA-BRICK definitions