ACC-ISDN DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, IpAddress, TimeTicks, Gauge, Counter FROM RFC1155-SMI TRAP-TYPE FROM RFC-1215 accTrapLogSeqNum, accTrapLogSeverityType FROM ACC-SYSTEM accBRG, DisplayString, RowStatus, IfIndex, SmdsAddress FROM ACC-MIB;-- Basic Rate ISDN Group accIsdn OBJECT IDENTIFIER ::= { accBRG 36 } -- The IsdnDsl Group accIsdnDsl OBJECT IDENTIFIER ::= { accIsdn 1 } -- Configuration and operational parameters maintained and -- reported on a per-terminal (bridge/router) basis. accIsdnDslIndex OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-only STATUS deprecated DESCRIPTION " An index instantiating a particular digital subscriber loop interface on this bridge/router terminal." ::= { accIsdnDsl 1 } -- The IsdnSub Group -- Configuration and operational parameters maintained and -- reported on a per-subscriber interface basis. accIsdnSubTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnSubEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " ISDN subscriber table containing configuration and operational parameters for all ISDN subscriber interfaces on this bridge/router terminal." ::= { accIsdn 2 } accIsdnSubEntry OBJECT-TYPE SYNTAX AccIsdnSubEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " Configuration and operational parameters for a particular ISDN subscriber interface." INDEX { accIsdnDslIndex } ::= { accIsdnSubTable 1 } AccIsdnSubEntry ::= SEQUENCE { accIsdnSubSwitchType INTEGER, accIsdnSubChannelMode INTEGER, accIsdnSubAdminStatus INTEGER, accIsdnSubDiagLevel INTEGER, accIsdnSubManualTei INTEGER } accIsdnSubSwitchType OBJECT-TYPE SYNTAX INTEGER { bri-net3(1), bri-5ess(2), bri-dms100(3), bri-vn2(4), bri-vn3(5), bri-kdd(6), bri-ntt(7), bri-1tr6(8), bri-ni1(9), bri-ccitt(10) } ACCESS read-write STATUS deprecated DESCRIPTION " The particular type of central-office switch providing access to the ISDN network and to which this subscriber interface is connected." ::= { accIsdnSubEntry 1 } accIsdnSubChannelMode OBJECT-TYPE SYNTAX INTEGER { cm-1b-plus-d(1), cm-2b-plus-d(2), cm-1h-plus-d(3) } ACCESS read-write STATUS deprecated DESCRIPTION " The ISDN channel configuration mode." ::= { accIsdnSubEntry 2 } accIsdnSubAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } ACCESS read-write STATUS deprecated DESCRIPTION " The administrative status of this subscriber interface." ::= { accIsdnSubEntry 3 } accIsdnSubDiagLevel OBJECT-TYPE SYNTAX INTEGER (0..5) ACCESS read-write STATUS deprecated DESCRIPTION " The current diagnostic message level for this subscriber interface." ::= { accIsdnSubEntry 4 } accIsdnSubManualTei OBJECT-TYPE SYNTAX INTEGER (0..63) -- 127 ACCESS read-write STATUS deprecated DESCRIPTION " The TEI (terminal endpoint identifier) when manual TEI assignment is required. Setting this value between 0 and 63 (inclusive) specifies manual TEI assignment using the indicated value. Setting this value to 127 (the broadcast TEI) specifies automatic TEI assignment." ::= { accIsdnSubEntry 5 } -- The IsdnStat Group -- Statistics and operational status maintained and -- reported on a per-subscriber interface basis. accIsdnStatTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnStatEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " Statistics and operational status maintained for all ISDN subscriber interfaces on this bridge/router terminal." ::= { accIsdn 3 } accIsdnStatEntry OBJECT-TYPE SYNTAX AccIsdnStatEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " Statistics and operational status for a particular ISDN subscriber interface." INDEX { accIsdnDslIndex } ::= { accIsdnStatTable 1 } AccIsdnStatEntry ::= SEQUENCE { accIsdnStatHdlcInPackets Counter, accIsdnStatHdlcInOctets Counter, accIsdnStatHdlcInErrors Counter, accIsdnStatHdlcInDiscs Counter, accIsdnStatHdlcOutPackets Counter, accIsdnStatHdlcOutOctets Counter, accIsdnStatHdlcOutErrors Counter, accIsdnStatHdlcOutDiscs Counter, accIsdnStatLapdUnsolicResps Counter, accIsdnStatLapdPeerSabmes Counter, accIsdnStatLapdN200Errors Counter, accIsdnStatLapdNrSeqErrors Counter, accIsdnStatLapdRecvdFrmrs Counter, accIsdnStatLapdCntlErrors Counter, accIsdnStatLapdInfoErrors Counter, accIsdnStatLapdWrongSizes Counter, accIsdnStatLapdN201Errors Counter, accIsdnStatCallsOriginateds Counter, accIsdnStatCallsOfferreds Counter, accIsdnStatCallsAnswereds Counter, accIsdnStatCallsAccepteds Counter, accIsdnStatCallsCompleteds Counter, accIsdnStatCallsCleareds Counter, accIsdnStatDslOperStatus INTEGER, accIsdnStatLastCauses INTEGER } accIsdnStatHdlcInPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of packets received on the D-channel of this subscriber interface." ::= { accIsdnStatEntry 1 } accIsdnStatHdlcInOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of octets received on the D-channel of this subscriber interface." ::= { accIsdnStatEntry 2 } accIsdnStatHdlcInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of input hardware errors counted by the D-channel input/output driver." ::= { accIsdnStatEntry 3 } accIsdnStatHdlcInDiscs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of input packets discarded by the D-channel input/output driver." ::= { accIsdnStatEntry 4 } accIsdnStatHdlcOutPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of packets transmitted on the D-channel of this subscriber interface." ::= { accIsdnStatEntry 5 } accIsdnStatHdlcOutOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of octets transmitted on the D-channel of this subscriber interface." ::= { accIsdnStatEntry 6 } accIsdnStatHdlcOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of output hardware errors counted by the D-channel input/output driver." ::= { accIsdnStatEntry 7 } accIsdnStatHdlcOutDiscs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of output packets discarded by the D-channel input/output driver." ::= { accIsdnStatEntry 8 } accIsdnStatLapdUnsolicResps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of unsolicited LAPD response frames received on all data links associated with the D-channel of this subscriber interface." ::= { accIsdnStatEntry 9 } accIsdnStatLapdPeerSabmes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of peer SABME frames received on all data links associated with the D-channel of this subscriber interface." ::= { accIsdnStatEntry 10 } accIsdnStatLapdN200Errors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of unsuccessful T200 timer recoveries after a frame has been retransmitted N200 times." ::= { accIsdnStatEntry 11 } accIsdnStatLapdNrSeqErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of N(R) sequence errors." ::= { accIsdnStatEntry 12 } accIsdnStatLapdRecvdFrmrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of LAPD FRMR response frames received." ::= { accIsdnStatEntry 13 } accIsdnStatLapdCntlErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of LAPD frames received with an invalid or non-implemented control field." ::= { accIsdnStatEntry 14 } accIsdnStatLapdInfoErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of LAPD frames received with a non-permitted information (I) field." ::= { accIsdnStatEntry 15 } accIsdnStatLapdWrongSizes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of LAPD frames received which were the wrong size." ::= { accIsdnStatEntry 16 } accIsdnStatLapdN201Errors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of LAPD frames received which contained and information field which exceeded N201." ::= { accIsdnStatEntry 17 } accIsdnStatCallsOriginateds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of outgoing calls originated on this subscriber interface." ::= { accIsdnStatEntry 18 } accIsdnStatCallsOfferreds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of incoming calls offerred on this subscriber interface." ::= { accIsdnStatEntry 19 } accIsdnStatCallsAnswereds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of outgoing calls originated on this subscriber interface which were answered by the destination." ::= { accIsdnStatEntry 20 } accIsdnStatCallsAccepteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of incoming calls offerred on this subscriber interface which were accepted for connection." ::= { accIsdnStatEntry 21 } accIsdnStatCallsCompleteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of outgoing and incoming calls completed (that is, the number of calls which were successfully connected)." ::= { accIsdnStatEntry 22 } accIsdnStatCallsCleareds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS deprecated DESCRIPTION " The number of outgoing and incoming calls cleared." ::= { accIsdnStatEntry 23 } accIsdnStatDslOperStatus OBJECT-TYPE SYNTAX INTEGER { inactive(1), -- layer-1 deactivated waiting(2), -- awaiting activation activated(3), -- layer-1 activated established(4) -- multi-frame established } ACCESS read-only STATUS deprecated DESCRIPTION " The operation status of this interface." ::= { accIsdnStatEntry 24 } accIsdnStatLastCauses OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION " The last cause value sent or received on this subscriber interface." ::= { accIsdnStatEntry 25 } -- The IsdnCall Group -- Parameters and operational status maintained and -- reported on a per-call basis. accIsdnCallTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnCallEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " Parameters and operational status for ISDN calls active on this bridge/router terminal." ::= { accIsdn 4 } accIsdnCallEntry OBJECT-TYPE SYNTAX AccIsdnCallEntry ACCESS not-accessible STATUS deprecated DESCRIPTION " Parameters and operational status for a particular ISDN call which is presently active or is in the process of being established or cleared." INDEX { accIsdnCallDslIndex, accIsdnCallIdentifier } ::= { accIsdnCallTable 1 } AccIsdnCallEntry ::= SEQUENCE { accIsdnCallIdentifier INTEGER, accIsdnCallReference INTEGER, accIsdnCallChannelId INTEGER, accIsdnCallIfIndex INTEGER, accIsdnCallInfoRate INTEGER, accIsdnCallState INTEGER, accIsdnCallCause INTEGER, accIsdnCallOrigin INTEGER, accIsdnCallAddress OCTET STRING, accIsdnCallDslIndex INTEGER } accIsdnCallIdentifier OBJECT-TYPE SYNTAX INTEGER (0..65536) ACCESS read-only STATUS deprecated DESCRIPTION " The internal call control identifier for this call." ::= { accIsdnCallEntry 1 } accIsdnCallReference OBJECT-TYPE SYNTAX INTEGER (1..32767) ACCESS read-only STATUS deprecated DESCRIPTION " The Q.931 call reference value for this call." ::= { accIsdnCallEntry 2 } accIsdnCallChannelId OBJECT-TYPE SYNTAX INTEGER { none(1), -- no channel allocated b1(2), -- B1 b2(3), -- B2 h0(4) -- hyperchannel (B1 + B2) } ACCESS read-only STATUS deprecated DESCRIPTION " The bearer channel interface ID allocated for this call." ::= { accIsdnCallEntry 3 } accIsdnCallIfIndex OBJECT-TYPE SYNTAX INTEGER { j1(1), -- J1 j2(2) -- J2 } ACCESS read-only STATUS deprecated DESCRIPTION " The interface index of the physical port connected by the bearer channel." ::= { accIsdnCallEntry 4 } accIsdnCallInfoRate OBJECT-TYPE SYNTAX INTEGER { packet(1), r-64k(17), r-2x64k(18), r-384k(20), r-1536k(22), r-1920k(24) } ACCESS read-only STATUS deprecated DESCRIPTION " The information transfer rate." ::= { accIsdnCallEntry 5 } accIsdnCallState OBJECT-TYPE SYNTAX INTEGER { disconnected(1), incoming(2), outgoing(3), routing(4), releaseing(5), connected(6) } ACCESS read-only STATUS deprecated DESCRIPTION " The current call control state (not Q.931)." ::= { accIsdnCallEntry 6 } accIsdnCallCause OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS deprecated DESCRIPTION " The last cause value associated with this call." ::= { accIsdnCallEntry 7 } accIsdnCallOrigin OBJECT-TYPE SYNTAX INTEGER { none(1), -- not yet originated terminal(2), -- outgoing (TE-to-NT) network(3) -- incoming (NT-to_TE) } ACCESS read-only STATUS deprecated DESCRIPTION " The originator of the call." ::= { accIsdnCallEntry 8 } accIsdnCallAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS deprecated DESCRIPTION " The remote call address associated with this call. For incoming calls, this is the calling ISDN address. For outgoing calls, this is the called ISDN address." ::= { accIsdnCallEntry 9 } accIsdnCallDslIndex OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-only STATUS deprecated DESCRIPTION " The interface index for the digital subscriber loop." ::= { accIsdnCallEntry 10 } -- ISDN Interface Group -- -- Implementation of the ISDN interface group is mandatory for all -- systems that implement a basic rate or primary rate ISDN -- interface. The ISDN interface group consists of three tables: -- ISDN Subscriber Table -- ISDN Statistics Table -- ISDN Call Table -- These tables are indexed by a digital subscriber loop (DSL) -- index which has the same value as the ifIndex for the ISDN -- interface. Prior to Release 8.0, the DSL index was a -- sequential integer index assigned independently of ifIndex. -- Due to the change in how ISDN tables are indexed, as well as -- other flaws in the ACC ISDN MIB definition, the following -- branches are being deprecated, and have been replaced by new -- branches: -- accIsdnDsl OBJECT IDENTIFIER ::= { accIsdn 1 } -- accIsdnSub OBJECT IDENTIFIER ::= { accIsdn 2 } -- accIsdnStat OBJECT IDENTIFIER ::= { accIsdn 3 } -- accIsdnCall OBJECT IDENTIFIER ::= { accIsdn 4 } -- ISDN Subscriber Table -- The ISDN Subscriber Table contains one entry for each BRI or -- PRI subscriber connection. Only ISDN interfaces with a D -- channel have an entry in this table. NFAS interfaces are not -- represented in this table. accIsdnxSubTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnxSubEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " ISDN subscriber table containing configuration and operational parameters for all ISDN subscriber interfaces on this bridge/router terminal." ::= { accIsdn 6 } accIsdnxSubEntry OBJECT-TYPE SYNTAX AccIsdnxSubEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the ISDN Subscriber Table" INDEX { accIsdnxSubDslIndex } ::= { accIsdnxSubTable 1 } AccIsdnxSubEntry ::= SEQUENCE { accIsdnxSubDslIndex INTEGER, accIsdnxSubSwitchType INTEGER, accIsdnxSubChanConfig INTEGER, accIsdnxSubAdminStatus INTEGER, accIsdnxSubDiagLevel INTEGER, accIsdnxSubManualTei INTEGER, accIsdnxSubOperStatus INTEGER, accIsdnxSubNumNfas INTEGER, accIsdnxSubLastCause INTEGER, accIsdnxSubSubaddrType INTEGER, accIsdnxSubVoiceOption INTEGER, accIsdnxSubCliOption INTEGER, accIsdnxSubEncodingMethod INTEGER, accIsdnxSubDialingMethod INTEGER, accIsdnxSubAutoSpid INTEGER, accIsdnxSubAutoSwitch INTEGER } accIsdnxSubDslIndex OBJECT-TYPE SYNTAX INTEGER -- (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION " The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device." ::= { accIsdnxSubEntry 1 } accIsdnxSubSwitchType OBJECT-TYPE SYNTAX INTEGER { bri-net3(1), bri-5ess(2), bri-dms100(3), bri-vn2(4), bri-vn3(5), bri-kdd(6), bri-ntt(7), bri-1tr6(8), bri-ni1(9), bri-ccitt(10), bri-tad2(11), bri-ts013(12), bri-ni2(13), pri-4ess(14), pri-5ess(15), pri-dms100(16), pri-net5(17), pri-vn3(18), pri-kdd(19), pri-ntt(20), pri-1tr6(21), pri-ccitt(22), pri-tad30(23), pri-ts014(24), pri-ni2(25), bri-auto-na(26) } ACCESS read-write STATUS mandatory DESCRIPTION " The particular type of central-office switch providing access to the ISDN network and to which this subscriber interface is connected." ::= { accIsdnxSubEntry 2 } accIsdnxSubChanConfig OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION " The ISDN channel configuration mode. Beginning with release 8.0, this is the number of bearer channels managed by the D channel. This object is normally read-only. It can be written only when changing the channel configuration from 2B+D to 1B+D on a Nile configured with a BRI in J1." ::= { accIsdnxSubEntry 3 } accIsdnxSubAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2), drain (3) } ACCESS read-write STATUS mandatory DESCRIPTION " The administrative status of this subscriber interface." ::= { accIsdnxSubEntry 4 } accIsdnxSubDiagLevel OBJECT-TYPE SYNTAX INTEGER (0..6) ACCESS read-write STATUS mandatory DESCRIPTION " The current diagnostic message level for this subscriber interface." ::= { accIsdnxSubEntry 5 } accIsdnxSubManualTei OBJECT-TYPE SYNTAX INTEGER (0..63) -- 127 ACCESS read-write STATUS mandatory DESCRIPTION " The TEI (terminal endpoint identifier) when manual TEI assignment is required. Setting this value between 0 and 63 (inclusive) specifies manual TEI assignment using the indicated value. Setting this value to 127 (the broadcast TEI) specifies automatic TEI assignment. This object is writable only for BRI subscribers. For PRI subscribers, the value read is always 0" ::= { accIsdnxSubEntry 6 } accIsdnxSubOperStatus OBJECT-TYPE SYNTAX INTEGER { deactivated (1), -- L1 deactivated activated (2), -- L1 activated, no L2 datalink established (3), -- L1 activated, L2 datalink, L3 quiet engaged (4) -- L1 activated, L2 datalink, L3 active } ACCESS read-write STATUS mandatory DESCRIPTION " The operational status of this subscriber interface." ::= { accIsdnxSubEntry 7 } accIsdnxSubNumNfas OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION " Indicates the number of NFAS trunks managed by this D channel." ::= { accIsdnxSubEntry 8 } accIsdnxSubLastCause OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION " The last clearing cause for a call associated with this interface." ::= { accIsdnxSubEntry 9 } accIsdnxSubSubaddrType OBJECT-TYPE SYNTAX INTEGER { nsap(1), user(2) } ACCESS read-write STATUS mandatory DESCRIPTION " Indicates the subaddress type for the ISDN interface." ::= { accIsdnxSubEntry 10 } accIsdnxSubVoiceOption OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION " Indicates whether the user is able to receive circuit mode voice calls" ::= { accIsdnxSubEntry 11 } accIsdnxSubCliOption OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION " Indicates whether a callers identifaction will be checked with known entries before accepting the call." ::= { accIsdnxSubEntry 12 } accIsdnxSubEncodingMethod OBJECT-TYPE SYNTAX INTEGER { a-law (1), mu-law(2) } ACCESS read-only STATUS mandatory DESCRIPTION " Companding algorithm to be used when initiating or answering voice calls over this interface. This is configured during initialization based on the user configured switch type." ::= { accIsdnxSubEntry 13 } accIsdnxSubDialingMethod OBJECT-TYPE SYNTAX INTEGER { overlap (1), enbloc (2) } ACCESS read-only STATUS mandatory DESCRIPTION " Dialing method to be used when initiating voice calls over the ISDN line. This is configured during initialization based on the user configured switch type." ::= { accIsdnxSubEntry 14 } accIsdnxSubAutoSpid OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } ACCESS read-write STATUS mandatory DESCRIPTION " SR-3888 Automatic SPID detection enabled or disabled for a BRI subscriber interface." ::= { accIsdnxSubEntry 19 } accIsdnxSubAutoSwitch OBJECT-TYPE SYNTAX INTEGER { unknown(1), manual(2), bri-ni1(3), bri-5ess(4), bri-dms100(5) } ACCESS read-only STATUS mandatory DESCRIPTION " The central-office switch type detected by the Automatic Switch detection function." ::= { accIsdnxSubEntry 20 } -- ISDN Statistics Table -- -- The ISDN statistics table contains one entry for each BRI or -- PRI subscriber loop connection. -- In the case of PRI subscribers, an entry exists only for PRI -- interfaces enabled for common channel signaling (i.e., -- interfaces containing a D channel). -- No statistics are maintained for NFAS-enabled subscriber loops. accIsdnxStatTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnxStatEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " Statistics and operational status maintained for all ISDN subscriber interfaces on this bridge/router terminal." ::= { accIsdn 7 } accIsdnxStatEntry OBJECT-TYPE SYNTAX AccIsdnxStatEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " An entry in the ISDN Statistics Table." INDEX { accIsdnxStatDslIndex } ::= { accIsdnxStatTable 1 } AccIsdnxStatEntry ::= SEQUENCE { accIsdnxStatDslIndex INTEGER, accIsdnxStatHdlcInPackets Counter, accIsdnxStatHdlcInOctets Counter, accIsdnxStatHdlcInErrors Counter, accIsdnxStatHdlcInDiscards Counter, accIsdnxStatHdlcOutPackets Counter, accIsdnxStatHdlcOutOctets Counter, accIsdnxStatHdlcOutErrors Counter, accIsdnxStatHdlcOutDiscards Counter, accIsdnxStatLapdUnsolicResps Counter, accIsdnxStatLapdPeerSabmes Counter, accIsdnxStatLapdN200Errors Counter, accIsdnxStatLapdNrSeqErrors Counter, accIsdnxStatLapdRecvdFrmrs Counter, accIsdnxStatLapdCntlErrors Counter, accIsdnxStatLapdInfoErrors Counter, accIsdnxStatLapdWrongSizes Counter, accIsdnxStatLapdN201Errors Counter, accIsdnxStatCallOriginateds Counter, accIsdnxStatCallOfferreds Counter, accIsdnxStatCallRouteds Counter, accIsdnxStatCallAccepteds Counter, accIsdnxStatCallCompleteds Counter, accIsdnxStatCallCleareds Counter } accIsdnxStatDslIndex OBJECT-TYPE SYNTAX INTEGER -- (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION " The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device." ::= { accIsdnxStatEntry 1 } accIsdnxStatHdlcInPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of packets received on the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 2 } accIsdnxStatHdlcInOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of octets received on the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 3 } accIsdnxStatHdlcInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of input hardware errors counted by the D-channel HDLC driver." ::= { accIsdnxStatEntry 4 } accIsdnxStatHdlcInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of input packets discarded by the D-channel HDLC driver." ::= { accIsdnxStatEntry 5 } accIsdnxStatHdlcOutPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of packets transmitted on the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 6 } accIsdnxStatHdlcOutOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of octets transmitted on the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 7 } accIsdnxStatHdlcOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of output hardware errors counted by the D-channel HDLC driver." ::= { accIsdnxStatEntry 8 } accIsdnxStatHdlcOutDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of output packets discarded by the D-channel HDLC driver." ::= { accIsdnxStatEntry 9 } accIsdnxStatLapdUnsolicResps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of unsolicited LAPD response frames received on all data links associated with the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 10 } accIsdnxStatLapdPeerSabmes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of peer SABME frames received on all data links associated with the D-channel of this ISDN interface." ::= { accIsdnxStatEntry 11 } accIsdnxStatLapdN200Errors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of unsuccessful T200 timer recoveries after a frame has been retransmitted N200 times." ::= { accIsdnxStatEntry 12 } accIsdnxStatLapdNrSeqErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of N(R) sequence errors." ::= { accIsdnxStatEntry 13 } accIsdnxStatLapdRecvdFrmrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of LAPD FRMR response frames received." ::= { accIsdnxStatEntry 14 } accIsdnxStatLapdCntlErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of LAPD frames received with an invalid or non-implemented control field." ::= { accIsdnxStatEntry 15 } accIsdnxStatLapdInfoErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of LAPD frames received with a non-permitted information (I) field." ::= { accIsdnxStatEntry 16 } accIsdnxStatLapdWrongSizes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of LAPD frames received which were the wrong size." ::= { accIsdnxStatEntry 17 } accIsdnxStatLapdN201Errors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of LAPD frames received which contained and information field which exceeded N201." ::= { accIsdnxStatEntry 18 } accIsdnxStatCallOriginateds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of outgoing calls originated on this ISDN interface." ::= { accIsdnxStatEntry 19 } accIsdnxStatCallOfferreds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of incoming calls offered on this ISDN interface." ::= { accIsdnxStatEntry 20 } accIsdnxStatCallRouteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of outgoing calls originated on this ISDN interface which were routed by the network." ::= { accIsdnxStatEntry 21 } accIsdnxStatCallAccepteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of incoming calls offered on this ISDN interface which were accepted for connection." ::= { accIsdnxStatEntry 22 } accIsdnxStatCallCompleteds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of outgoing and incoming calls completed (that is, the number of calls which were successfully connected)." ::= { accIsdnxStatEntry 23 } accIsdnxStatCallCleareds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION " The number of outgoing and incoming calls cleared." ::= { accIsdnxStatEntry 24 } -- ISDN Call Table -- The ISDN call table contains an entry for each call in -- progress. A call is in progress if its call state is -- non-zero (i.e., not IDLE). All calls on all ISDN interfaces -- are co-mingled in the same table. accIsdnxCallTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnxCallEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " Parameters and operational status for ISDN calls in progress on this bridge/router terminal." ::= { accIsdn 8 } accIsdnxCallEntry OBJECT-TYPE SYNTAX AccIsdnxCallEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " An entry in the ISDN Call Table." INDEX { accIsdnxCallDslIndex, accIsdnxCallReference, accIsdnxCallOrigin } ::= { accIsdnxCallTable 1 } AccIsdnxCallEntry ::= SEQUENCE { accIsdnxCallDslIndex INTEGER, accIsdnxCallReference INTEGER, accIsdnxCallOrigin INTEGER, accIsdnxCallCircuitIndex INTEGER, accIsdnxCallInfoRate INTEGER, accIsdnxCallState INTEGER, accIsdnxCallCause INTEGER, accIsdnxCallAddress OCTET STRING, accIsdnxCallInfoType INTEGER, accIsdnxCallSlotMap INTEGER } accIsdnxCallDslIndex OBJECT-TYPE SYNTAX INTEGER -- (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION " The ifIndex of an ISDN BRI, DBRI, PRI/T1 or PRI/E1 interface on this managed device." ::= { accIsdnxCallEntry 1 } accIsdnxCallReference OBJECT-TYPE SYNTAX INTEGER (1..32767) ACCESS read-only STATUS mandatory DESCRIPTION " The Q.931 call reference value for this call." ::= { accIsdnxCallEntry 2 } accIsdnxCallOrigin OBJECT-TYPE SYNTAX INTEGER { none(1), -- unknown terminal(2), -- outgoing (TE-to-NT) network(3) -- incoming (NT-to-TE) } ACCESS read-only STATUS mandatory DESCRIPTION " The originator of the call." ::= { accIsdnxCallEntry 3 } accIsdnxCallCircuitIndex OBJECT-TYPE SYNTAX INTEGER -- (1..'7fffffff'h) ACCESS read-only STATUS mandatory DESCRIPTION " The ifIndex for the circuit associated with this call." ::= { accIsdnxCallEntry 4 } accIsdnxCallInfoRate OBJECT-TYPE SYNTAX INTEGER { info-rate-1x64k(1), info-rate-2x64k(2), info-rate-3x64k(3), info-rate-4x64k(4), info-rate-5x64k(5), info-rate-6x64k(6), info-rate-7x64k(7), info-rate-8x64k(8), info-rate-9x64k(9), info-rate-10x64k(10), info-rate-11x64k(11), info-rate-12x64k(12), info-rate-13x64k(13), info-rate-14x64k(14), info-rate-15x64k(15), info-rate-16x64k(16), info-rate-17x64k(17), info-rate-18x64k(18), info-rate-19x64k(19), info-rate-20x64k(20), info-rate-21x64k(21), info-rate-22x64k(22), info-rate-23x64k(23), info-rate-24x64k(24), info-rate-25x64k(25), info-rate-26x64k(26), info-rate-27x64k(27), info-rate-28x64k(28), info-rate-29x64k(29), info-rate-30x64k(30), info-rate-31x64k(31), packet(32) } ACCESS read-only STATUS mandatory DESCRIPTION " The information transfer rate." ::= { accIsdnxCallEntry 5 } accIsdnxCallState OBJECT-TYPE SYNTAX INTEGER { idle (1), initiated (2), overlap-send (3), outgoing (4), delivered (5), present (6), received (7), connecting (8), incoming (9), active (10), discon-req (11), discon-ind (12), suspend (13), resume (14), release (15), overlap-recv (16) } ACCESS read-only STATUS mandatory DESCRIPTION " The Q.931 call control state." ::= { accIsdnxCallEntry 6 } accIsdnxCallCause OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION " The last cause value associated with this call." ::= { accIsdnxCallEntry 7 } accIsdnxCallAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION " The remote call address associated with this call. For incoming calls, this is the calling ISDN address. For outgoing calls, this is the called ISDN address." ::= { accIsdnxCallEntry 8 } accIsdnxCallInfoType OBJECT-TYPE SYNTAX INTEGER { info-type-cmd (1), -- circuit mode data (64kb/sec) info-type-cm56 (2), -- circuit mode data (56kb/sec) info-type-cmv (3) -- circuit mode data over voice } ACCESS read-only STATUS mandatory DESCRIPTION " The information transfer type: info-type-cmd circuit mode data, clear channel 64 kbits/s info-type-cm56 circuit mode data, rate-adapted to 56 kbits/s info-type-cmv circuit mode data over voice circuit" ::= { accIsdnxCallEntry 9 } accIsdnxCallSlotMap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION " A 31-bit mask which identifies the time-slots forming a hyperchannel." ::= { accIsdnxCallEntry 10 } -- The IsdnTest Group accIsdnTest OBJECT IDENTIFIER ::= { accIsdn 5 } -- Parameters and commands maintained and reported on a -- per-terminal basis used for controlling homologation -- testing. accIsdnTestIfIndex OBJECT-TYPE SYNTAX INTEGER { j1(1), -- J1 j2(2) -- J2 } ACCESS read-write STATUS mandatory DESCRIPTION " The interface index for the physical port from which a call will be made." ::= { accIsdnTest 1 } accIsdnTestAddress OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION " The ISDN destination call address." ::= { accIsdnTest 2 } accIsdnTestCommand OBJECT-TYPE SYNTAX INTEGER { normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), loop(8), unloop(9), activate(10), deactivate(11), display(12) } ACCESS read-write STATUS mandatory DESCRIPTION " The action to be performed." ::= { accIsdnTest 3 } accIsdnTestRouting OBJECT-TYPE SYNTAX INTEGER { normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), activate(8), deactivate(9), loop4(10), reset(11), display(12), ones(13), zeros(14), bon(15), boff(16) } ACCESS read-only STATUS mandatory DESCRIPTION " The action to be performed for incoming calls." ::= { accIsdnTest 4 } accIsdnTestRegName OBJECT-TYPE SYNTAX INTEGER { nr0(0), nr1(1), nr2(2), nr3(3), nr4(4), nr5(5), nr6(6), br0(16), br1(17), br2(18), br3(19), br4(20), br5(21), br6(22), br7(23), br8(24), br9(25), br10(26), br11(27), br12(28), br13(29), br14(30), br15(31) } ACCESS read-write STATUS mandatory DESCRIPTION " The name of the MC145474 register to write. " ::= { accIsdnTest 5 } accIsdnTestRegValue OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION " The value to write to the MC145474 register." ::= { accIsdnTest 6 } accwIsdnTestBChanMode OBJECT-TYPE SYNTAX INTEGER { normal(1), accept(2), reject(3), ignore(4), call(5), clear(6), disconnect(7), activate(8), deactivate(9), loop4(10), reset(11), display(12), ones(13), zeros(14), bon(15), boff(16) } ACCESS read-write STATUS mandatory DESCRIPTION " The action to be performed on the B-channel." ::= { accIsdnTest 7 } accwIsdnTestOptions OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " Test options in hex." ::= { accIsdnTest 8 } -- ISDN SPID group accIsdnSpidTable OBJECT-TYPE SYNTAX SEQUENCE OF AccIsdnSpidEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " Valid SPIDs currently Registered with the CO, required for placing/accepting calls." ::= { accIsdn 9 } accIsdnSpidEntry OBJECT-TYPE SYNTAX AccIsdnSpidEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " SPID information entry in the SPID Table." INDEX { accIsdnSpidIndex } ::= { accIsdnSpidTable 1 } AccIsdnSpidEntry ::= SEQUENCE { accIsdnSpidIndex INTEGER, accIsdnSpidValue DisplayString } accIsdnSpidIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION " An Index to Ports of B-channels." ::= { accIsdnSpidEntry 1 } accIsdnSpidValue OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION " Value of SPID,Required for the terminal to be active on the S/T bus." ::= { accIsdnSpidEntry 2 } -- The IsdnTermination Status accIsdnTerm OBJECT IDENTIFIER ::= { accIsdn 10 } -- Used for setting the Termination status on a Congo S/T interface accIsdnxTermination OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION " ISDN Bus Termination status" ::= { accIsdnTerm 1 } accIsdnxCurrCalls OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION " Number of active ISDN calls" ::= { accIsdn 11 } -- START CFG_TRAP_ENHANCEMENTS -- Isdn traps accIsdnTraps OBJECT IDENTIFIER ::= { accIsdn 12 } accIsdnTrapMsg OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION " ISDN Trap Message " ::= { accIsdnTraps 1 } -- END MANILA_NEW accIsdnOutGoingCallTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While initializing the call control block. When the call was first originated to establish the correct connection endpoint specifier to use, there is a check on failing which this trap is generated SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 1 accIsdnCallResetTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "When a catestrophic event occurs, if there is no recovery because of less cblks, then the call is simply forced to clear, which is cause for this call reset trap SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 2 accIsdnConnectTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Indication thruough this trap is a failure of Connect if the ICCB channel is present. Else deicdes there is no bearer channel and sends this trap. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 3 accIsdnStaleDialCntxtTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "This trap is triggered when there is a mismatch in the Magicnumber. Treating it as a stale dial. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 4 accIsdnIncomingCallTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "This is generated during identifying the calling party, if the call has to be refused based on the validity of the calling number. The reason is also stated in the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102 " ::= 5 accIsdnCallTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "This is generated during identifying the called party, if the call has to be refused based on the validity of the called number. The reason is also stated in the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102 " ::= 6 accIsdnApplTmrExpTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the application timer expires during the call setup, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102 " ::= 7 accIsdnApplTmrExpInClearTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the application timer expires during the call clearing, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 102 " ::= 8 accIsdnChannelRestrtTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While determining valid the channel stat, if the action is to restart the channel, then the appropriate B-Channel is restarted. This trap indicates such a situation. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 9 accIsdnDataLnkRelTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg, accTrapLogSeverityType , accTrapLogSeqNum} DESCRIPTION "If the D-channel Data Link is is to be released making Datalink down, then this trap is triggered. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 108 " ::= 10 accIsdnDataLnkEstTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg, accTrapLogSeverityType , accTrapLogSeqNum} DESCRIPTION "If the D-Channel Data Link is established making Datalink UP, then this trap is triggered. SEVERITY-DEFAULT: Clear EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 108 " ::= 11 accIsdnConfigStackTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the ISDN stack cannot be configured because of reasons like unspecified switch type, or not supporting DCBU etc., then this trap is generated which is conveying that a configuration error has occured. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 12 accIsdnSubscriberLoopTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "When a catestorphic error like low cblk conditions occur, then it tries to recover by restting the subscriber's loop. That is when this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 13 accIsdnRegisterTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the registration name is not identified and found in the list, then it sends this trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 14 accIsdnTrmnlRegErrTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If there is a error in getting the SPID indicates that the it is a unknown CES or may be a inoppurtune event has occured and hence the terminal registration error is sent. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 15 accIsdnTrmnlRegTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "In the event SPID state being pending indicates that the the terminal registration failed. This trap indicates the same. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 16 accIsdnAwaitDatalnkEstTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the SME_TERM_REGISTER request is apparently stuck, most likely because a datalink cannot be established, then this trap is generated. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 17 accIsdnDisconnectTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the CCB state is proceeding and the ISDN CHANNEL ID is none then this trap can be triggered after which the call is abort. SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 6 " ::= 18 accIsdnOutGoingCallFailTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "In the process of disconnect request from the RM Manager if there isn't any active call, then this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 19 accIsdnTrap20 TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the RM Dial manger sends the request to set up and if it fails for various reason, then this trap is generated. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 20 accIsdnModuleErrTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the application timer expires during the call setup, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 21 accIsdnTrap22 TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the application timer expires during the call clrearing, then the call is aborted. This trap is sent to convey the same. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 22 accIsdnNfasIntfTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If there is a application-dependent error then this trap displays the module function and the error message. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 46 " ::= 23 accIsdnNoSpidTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While initialsing the layer1 task, if the interface is configured for NT mode, then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 24 accIsdnSpidConflictTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the trial to get the internal interface id fails it means the NFAS interface is not properly defined. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 25 accIsdnInvSpidTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While getting the SPID tries to find the port. In the process if the port is not found and a corresponding PP index is not found then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 26 accIsdnSwBldTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While getting the SPID, it comapres the interface flag and if there is a match, it triggers a config error, and hence the trap saying conflicting SPIDs. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 27 accIsdnParametersTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If the SPID is too lengthy which is not supported then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 28 accIsdnSwitchTypeTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Determines whether or not operating as the network side (NT) or user side (TE) and records this in the DSL entry. And generates a trap if the hardware configuration is not consistent with the software system build (Telenetworks requires USER vs. NETWORK to be bound at compile-time). SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 29 accIsdnManyIntfTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "While initialzing the ISDN parameters, it validates from the NVM. While doing so if a error is encountered this config error trap is sent. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 30 accIsdnPriGroupRangeTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Tries to make sure the switch type configured for the subscriber entry has been included in the system build. If not, generates this trap and proceeds as if the entry had been disabled. Also, makes sure the switch type is consistent with the installed interface. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 31 accIsdnNfasIntfPriTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "The maximum number of DSL entries is limited at compile time by the Telenetworks code. When it exceeds this this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 32 accIsdnManyNFASIntfTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "If during initialization a invalid group is encountered as it is out of the range, then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 33 accIsdnPriGroupTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Looks for interfaces in PRI group 0. If the interface has a signaling channel, it is assumed to be a stand-alone interface. Otherwise, it is a orphan (i.e., misconfigured) NFAS interface, hence generates the trap. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 34 accIsdnTrap35 TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "In the event of making sure the PRI group has a primary signaling interface and that the group can accommodate an additional NFAS interface, if the new pri id or secondary new id exceed the maximum interface id, this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 35 accIsdnNoSrvcProIFTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION " No service profile identifier SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 36 accIsdnNTBldIncmptblHWTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION " Software NT build is incompatible with harware TE mode SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 37 accIsdnRcvdSpidTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg, accIsdnSpidValue , accTrapLogSeqNum} DESCRIPTION " Received one spid SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 38 accIsdnRcvdSpidsNWTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg, accIsdnSpidValue , accTrapLogSeqNum} DESCRIPTION "Received spids from network SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 39 accIsdnAutoSpidFldTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto spid failed (found %d suitable SPID(s)) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 40 accIsdnAutoSpidSccdTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto spid succeeded SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 41 accIsdnAutoSpidFld1Trap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto spid failed (cause = %d) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 42 accIsdnAutoSwtchSccdTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto switch detection succeeded SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 43 accIsdnAutoSwtchFldTrap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto switch detection failed (unspecified switch type) SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 44 accIsdnAutoSwtchFld1Trap TRAP-TYPE ENTERPRISE accIsdnTraps VARIABLES { accIsdnTrapMsg , accTrapLogSeqNum} DESCRIPTION "Auto switch detection failed SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accIsdnTrapMsg } PCAUSE-DEFAULT: 7 " ::= 45 END